# 1
Draw-Tite Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 8-1/2" Long - 7.5K
Excellent quality, fast shipping. Finding a metric ball for our international application was a bit difficult. We knew etrailer was the place to go for all things "trailer" related. Very happy with the purchase!
Strong and seems to be well made and well finished. One-inch ball mounting hole. I used this for a Curt hitch mounted on a 2014 Forester and pulls a small Harbor Freight trailer. Perfect height and trailer is level. Warning - don't get their hitch pin, it does not have a hole for a cotter pin, only a weak clip that I would not trust.
# 2
Curt Class III Ball Mount with 2" Ball - 2" Drop - 7,500 lbs
I have two of these. My first I bought two years ago. I very highly recommend this Curt Class III Ballmount 2" Drop because of its price, durability and quality. I towed various class 3 loads with ease and confidence with this ballmount. It slides into the hitch and does its job without fail. It looks excellent after towing a load. etrailer's price is about as good as it gets and delivery is very speedy.
Easy install, took around 30 minutes by my self to install. Hardest part of install was torquing the bolts ! Installed 13322 Class III Hitch - Gm 1500/2500 Pickup and Curt Class III Ballmount -2ball-2 Drop
# 3
Draw-Tite Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 9" Long - 7.5K
Working in the sand and grass of my driveway my wife and I installed our new etrailer receiver hitch. Great fit and finish! Went right on as described in the online guide. Hitch required a spacer washer on top back bolt attachment point. Taped it on so it would not move while lifting in place and it stayed right there! Used a car jack to raise up and hold the hitch into the underside of the trunk tighten the bolts and reattached the tail pipe done. Now we can pull our Sunfish Sailboat any where the car will go.
I am very pleased with the hitch, ball mount, and electrical package. All were easy to install if you follow the easy to understand directions. An added plus for putting one of these on a MINI is that the hitch can be hidden behind the "black plate/cover" that is on the rear bumper. It looks just like it came out of the factory except when to need to install the ball mount. The service has been outstanding. This is the place to go.
# 4
Curt Class III Ball Mount with 1-7/8" Ball - 2" Drop - 3,500 lbs
Works perfectly. Fast shipping. Very Satisfied.
Very pleased with etrailer. Very easy to order from website. Fast delivery, easy to install ,perfect fit . Thanks. .
# 5
Curt Drawbar for 1-1/4" Hitches - 3-1/8" Rise - 9-1/4" Long - 3,500 lbs
I would give five stars but due to what looks like packaging problems the hitch came very marred and the coating chipping off.
Good and strong but not a great angle/height for my application so had to go to a straight line fit.
# 6
Curt Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs
With good information from the website it was easy to order a Curt 2" Trailer Hitch, the Upgraded Circuit Protected Tail Light Converter Hardwire Kit w/ 4-Pole Connector and Circuit Tester - 119178KIT, Curt Ball Mount for 2" Hitches (3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs - D-4), Curt Pin and Clip Hitch Receiver - C21500, Rubber Tube Cover for 2" Trailer Hitch Receivers - I-728,Review, and 2" hitch ball 40038. Parts were delivered earlier than the initial estimate. Self installation (on a sloped drive way) took just under 2 hour. The fit of parts was very good, instructions and on-line video's were very helpful. My Kia did not have the wire plug in option, but the splice connections in the wire kit were easy to install. Most of the parts are hidden from view when the ball mount is not used.
I have a custom made tow guard. The ball mount I have was too short to allow me to attach the tow guard to my new truck. I searched the web and found just what I needed at etrailer.com. It's the only site I found that carried the size I needed. The product fits my needs perfectly. I can now protect my boat from rocks and other road debris when towing. Thank you etrailer.com.
# 7
Curt Multipurpose Ball Mount with 2" Receiver for Bike Racks and Cargo Carriers - 7,500 lbs
I am using the hitch for a car dolly and a bike rack. The fit is a little loose for the bike rackmI'll see it really works when get on the road.
Quality is excellent. However, it did not work so I am not sure what to do with it. I thought I could use the top hitch for a Bike rack and pull a utility trailer with other toys. The trailer is too close to make a turn so good try but not able to use it. Thank you for asking. I did not open the box for a while because I was having the trailer worked on so assumed I waited too long to return.
# 8
Curt Tri-Ball Mount - 3 Chrome Balls - 10,000 lbs
definitely solid as a rock
Excellent product! With the three different ball sizes, this tri-ball mount gives you a lot of flexibility. Gone are the days of having several different ball mounts to fit different tongues. High quality construction makes this an excellent investment.
# 9
Curt Multi-Ball Adjustable Ball Mount for 2" Trailer Hitches
Picked up my teardrop in ABQ on 2/17/23, and the Curt ball mount lined up perfectly with no drop/rise, and the extra length gave clearance for my rear door mounted spare tire. This mount is a beast, and the "overbuilt" nature of it gave me confidence that my Bronco would tow the teardrop easily. I also got the Curt Echo wireless brake controller, which synced easily to my phone and was easy to install, set up, and use. Overall a great towing experience, thanks to etrailer and Curt!
Very versatile - can use it on both my vehicles that have very different hitch height. Clean welds, super solid. Weighs a LOT!
# 10
MaxxTow Adjustable-Height Ball Mount - 2" Hitch - 7-1/2" Drop, 6-1/4" Rise - 5,000 lb
As advertised and quick delivery, I am an Etrailer fan!
Strong and works perfectly!
# 11
Curt Ball Mount for 2" Hitches - 4" Rise, 6" Drop - 9-1/4" Long - 7,500 lbs
I bought this on my knowledgeable brother's advice - he gave me the exact order number and link to buy from etrailer! I had it installed locally, without complications. I use my truck mostly to haul my horse or my friend's two donkeys in my 14-foot stock trailer. I have no complaints, the hitch does what it's supposed to do.
Easy install, everything included, and great instructional video. Worked out great for my RAV4.
# 12
Curt Class II Drawbar - 5" Rise - 9-5/8" Long - 3,500 lbs
I am an infrequent trailer user, but getting my daughter home from college was necessary in March. This drawbar fits my hitch and utility trailer well, did exactly what it is supposed to do, and was the last thing to be concerned about right then. I have a '11 Mini Countryman S with a Class II receiver from Mini Fini, (which cost twice as much as a Curt) where the hole is flush with the fake grille near the bottom of the bumper cover, so I needed the long bar to reach out past the bumper. The Curt receiver for that car hangs visible underneath the bumper (ugly), which also increases the lever arm on the receiver beam and would have needed an even taller rise. (Curt take note!) All just part of the kit to create an occasional 1 ton pickup out of my Mini, leaving the "bed" at home most of the time.
Fits perfectly. I just wish you would’ve sent a pin with it because I had to go chase that down and get an aftermarket one at Ace Hardware.
# 13
Curt Ball Mount for 2" Hitches - 4" Rise, 6" Drop - 14-1/4" Long - 6,000 lbs
The Extra Long Ball Mount proved useful immediately upon receipt. Delivery was prompt, and the updates from etrailer.com helped plan transport of several bicycles, simultaneously with a camper trailer. The extended length facilitated use with a Swagman bicycle rack, also purchased via etrailer.com. The product arrived in excellent condition, with correct capacity rating, and works perfectly, and in conjunction with the bicycle rack. I recommend purchases from etrailer.
Product is exactly as described on the etrailer.com website and measurements and dimensions fit perfect. Easy phone order process and prompt delivery, standard shipping arrived 3 business days after the order was placed. The extra long version of the ball mount makes it perfect for me to put on the bike rack while towing my horses.
# 14
Ball Mount 3/4" Rise or 2" Drop - 12-5/8" Long
The one foot ball mount works great on a 2014 Chevrolet Silverado work truck(no lift kit). We use it for a one axle, lawn care/utility trailer. It is used at least half the work week and has held up for a year. It may not be a good choice for a heavier trailer, but at that point we would also purchase a 2500 truck too. The mount helps clear the jack when the tailgate is opened with about 2 inches to spare.
Great product for getting out past the tire carrier on a small SUV. Customer service was wonderful with great follow through and any assistance I needed I will definitely use etrailer agin
# 15
Convert-A-Ball Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 10,000 lbs
Good, very solid ball mount with just the extra rise I needed, 2 3/4", to get level trailer and good clearance for the trailer jack. But excessive shipping charges from etrailer, $[XX] for an $[XX] purchase. Found out to my cost later that [online vendor] would have shipped for free.
As a full-time RVer, e-shopping is very important for us. etrailer was the right place to shop. Right product, delivered on-time for a great price. You beat the local discount RV store by $25 including shipping. At the same time, I had another outfit send me a clearly inferior product to the one they displayed. Said they would e-mail a pre-paid shipping label for the return (didn't) and tried to put the blame on Amazon. Thanks etrailer for a great experience !
# 16
Convert-A-Ball Dual-Cushioned, Adjustable Ball Mount - 7" Rise to 9-1/2" Drop - 5,000 lbs
We bought this to tow our 3,000 lbs. boat with our Subaru Ascent with a 5,000 lbs. towing capacity. With the OEM ball mount, we could really feel every jolt and jiggle from hard stops, going over bumps in the road, and trailering down dirt roads. However, the dual cushion ball has really improved our trailing experience. Once we get up to speed, we hardly notice we are towing our boat. It's also great because some of the lakes we visit are down dirt roads, and the cushion makes this a much more pleasant experience. I would highly recommend this to anyone towing a boat or larger trailer with a SUV as it maintains that comfortable ride and the jostling of the trailer is much less noticeable.
Rusted within 30 days. The manufacturer refused to warranty the product. I have continued to use it, but it has required some serious rust mitigation and is a flawed product.
# 17
Hidden Hitch Ball Mount - 3/4" Rise, 2" Drop - 15-3/4" Long - 6,000 lbs
Ordered this hitch and it worked perfect for what I needed just bought a teardrop trailer. Couldn't open up the tailgate on my Jeep so I ordered this extended hitch and I brought the ball out past my spare tire and the tailgate opens up now I have no problems. And I looked everywhere couldn't find one of this quality and at this price very reasonable the other ones hundreds of dollars didn't want to spend that much.
This was the longest hitch ball mount I could find anywhere. I used it with a short extension for my 2021 T G so that I could open the back doors without hitting the trailer wheel crank. With my new trailer, Intact Flyer Discover, I don't need the extension and can still open the doors. Works well.
# 18
Draw-Tite Drawbar for 1-1/4" Hitches - 4" Rise - 10" Long - 2,000 lbs
works well brings the trailer tongue up to level. I have it on an EV so the raddle is annoying, because I just keep on forgetting to buy a anti rattler.
This is very sturdy hitch. It is made of solid steel, not tubing. It will be used on my Mazda RX-3 to tow my car dolly to the RV lot where I will swap everything around and the car will end up on the dolly behind my RV.
# 19
B&W Tow & Stow Pintle Hook with 2" Ball - 2" Hitches - 10,000 lbs/16,000 lbs
Great product and very helpful folks to talk to. I’ve ordered from etrailer many times and it won’t be my last.
This hitch is a very handy addition to my toolbox! I work for a county road department, and I’m always pulling different trailers to and from job sites. I can switch from a 2 5/16” ball hitch, to a pintle hitch with the flip of a lever! Thanks B and W!
# 20
B&W Tow & Stow Pintle Hook with 2-5/16" Ball - 2" Hitches - 10,000 lbs/16,000 lbs
Works great! I use this hitch on a regular basis utilizing the ball on one use and pintle on the other. I often drive over rough terrain pulling a Tucker Terra Sno-Cat or a 50kW genset, this hitch handles the roughness. The universal hitch is optimum when hauling via pintle or ball.
It works good but to me it wears a little too much from the movement of the Pintle on the flat section where the pintle sits on the hitch
What our customers are saying:
"In these days of customer "no service" I am usually disapointed when doing business with people I don't know. It was refreshing doing business with you. I'm impressed!"