Best Dodge Caravan Trailer Hitch Ball Mounts

fit perfect.

Everything was perfect.! Nice paint, package, and fast shipping.! Im satisfied.!

To be honest, I use it upside down. I needed a hitch with rise, but none were available at time of purchase, and yours, inverted, works perfectly! The welds are regularly checked and remain all secure. It's a good hitch.

Working in the sand and grass of my driveway my wife and I installed our new etrailer receiver hitch. Great fit and finish! Went right on as described in the online guide. Hitch required a spacer washer on top back bolt attachment point. Taped it on so it would not move while lifting in place and it stayed right there! Used a car jack to raise up and hold the hitch into the underside of the trunk tighten the bolts and reattached the tail pipe done. Now we can pull our Sunfish Sailboat any where the car will go.

Strong and seems to be well made and well finished. One-inch ball mounting hole. I used this for a Curt hitch mounted on a 2014 Forester and pulls a small Harbor Freight trailer. Perfect height and trailer is level. Warning - don't get their hitch pin, it does not have a hole for a cotter pin, only a weak clip that I would not trust.

I searched the internet to put a hitch on my 2016 Chevy Equinox and found an instructional video from eTrailer.com where they installed on my exact car. I decided to go with eTrailer.com because they answered all my questions and because of the video-I support businesses that go the extra mile with these videos. Shipping was quick and well tracked, however, the box was flimsy and the one end of the hitch had come out of the box side and the ball mount could have easily come out of that hole during shipping. If I were eTrailer.com I'd charge an extra couple of bucks for more sturdy boxes-people will still buy as eTrailer is a well-trusted brand and this would overcome a lot of the negative reviews you'll see on their site about this shipping issue in their own reviews :-) I installed the hitch by myself (definitely recommend help as two people holding it up to the frame makes attaching 100% easier) in about 45 minutes total (out of the box, read instructions, review video again and installation complete). All hardware went on with no issues. Great quality hitch! I also bought the lesser expensive wiring assembly because most recent equinox's come hitch ready with pre-wired assembly in the left side compartment-snap and done. Picked up a new trailer at Home Depot within days and drove 5 feet and the clacking was horrible. I had always had a welded hitch before buying a hitch that took a ball mount. I really thought something was wrong and when I searched the internet that night it turns out this is very common. However, all you need is some sort of hitch "silencing" device. The number of options will drive you mad but I went with the Roadmaster Quiet Hitch and it did the trick for much less than most of the other options. If I were eTrailer.com I'd have that as one of the RECOMMENDED add-ons and explanation why its super-worthy when customers are buying a hitch. Would have saved me the time and hassle of dealing with it later and the extra shipping charge for buying after the fact when I got free shipping for the other items the first time :-) All in all, I'm super, super happy with my hitch, wiring assembly, ball mount, ball mount locking pin and the hitch silencer. Buy with confidence from eTrailer.com Paul R., Syracuse, NY

Easy to use and haven't had any trouble towing my small trailer with motorcycle on board. Def recommend.

This part came with the trailer hitch I purchased. It was very easy to transfer the ball from my 2" hitch and voila I am now ready to haul my trailer.

etrailer has what you need

I would give five stars but due to what looks like packaging problems the hitch came very marred and the coating chipping off.

Nice and heavy duty. Make sure you order the 1/2" pin when you order this.

We really like the hitch we ordered for our Camry. It was extremely easy to install. Fit perfectly!

My Mini Cooper is lowered and this unit really helped level out the trailer I am pulling. The product is heavy and solid. I would definitely recommend this item

Heavy duty! I was a little bummed when I found out how much more difficult it was to find a half inch pin for this, but no matter. It is a tad loose inside the hitch, so there's a little rattle, but I doubt it's as noticable as I make it seem. Super classy and a welcome change from the typical draw bar style. Goes great with my Volvo V70 T5. Thanks etrailer.com!

The Extra Long Ball Mount proved useful immediately upon receipt. Delivery was prompt, and the updates from etrailer.com helped plan transport of several bicycles, simultaneously with a camper trailer. The extended length facilitated use with a Swagman bicycle rack, also purchased via etrailer.com. The product arrived in excellent condition, with correct capacity rating, and works perfectly, and in conjunction with the bicycle rack. I recommend purchases from etrailer.

Works great solid product.

I like the look of this set very much and it is easy to mount and adjust the ball mount. The workmanship and finish are beautiful. Customer service was excellent in assuring I found the correct mount for my Ford Escape. I pull my 6'x10' utility trailer or very seldom my pontoon trailer. I like that the adjustable mount comes off very easily as I remove it until I need it while my vehicle is in the garage--it helps prevent knocking your leg against it in the garage. However, I am not having any luck loosening the bolt that secures the 2 chrome balls to the adjustable ball mount; I have the correct Allen wrench but cannot exert sufficient torque to loosen the bolt while the adjustable ball holder is off the ball mount. I want to put a different ball combination on so I can pull my son's trailer, which has a smaller ball than comes with the set, if I have to. I also added the anti-rattle device and it stops the mount completely.

Solid product that I look forward to using. It's appearance in the bright polished aluminum almost makes it too beautiful to use! The adjustable height settings will surely meet the requirement for any trailer that I'll ever haul. With a 39.25" upper wheel well from the ground measurement, the adjustable ball mount gives me a 16-to-21in measurement from the ground to the top of ball.

Overly tight on the receiver end bit functions as intended.

I am an infrequent trailer user, but getting my daughter home from college was necessary in March. This drawbar fits my hitch and utility trailer well, did exactly what it is supposed to do, and was the last thing to be concerned about right then. I have a '11 Mini Countryman S with a Class II receiver from Mini Fini, (which cost twice as much as a Curt) where the hole is flush with the fake grille near the bottom of the bumper cover, so I needed the long bar to reach out past the bumper. The Curt receiver for that car hangs visible underneath the bumper (ugly), which also increases the lever arm on the receiver beam and would have needed an even taller rise. (Curt take note!) All just part of the kit to create an occasional 1 ton pickup out of my Mini, leaving the "bed" at home most of the time.

works well brings the trailer tongue up to level. I have it on an EV so the raddle is annoying, because I just keep on forgetting to buy a anti rattler.

This is very sturdy hitch. It is made of solid steel, not tubing. It will be used on my Mazda RX-3 to tow my car dolly to the RV lot where I will swap everything around and the car will end up on the dolly behind my RV.

This is exactly what I needed for my front end mounted receiver.

As advertised and quick delivery, I am an Etrailer fan!

Very good quality, and exactly the right amount of drop to level up my utility trailer.

All equipment was delivered on time. Hitch, wiring harness, receiver and ball. Watched video's on installation of harness and hitch. Went down to my garage and installed both with the help of my girlfriend. Very satisfied with the products and the installation. etrailer supplied the goods and the knowledge. I am very happy that I went this route.

Worked perfectly. Super easy installation and it carried a U-haul 5x8 trailer 1000 miles with almost full capacity on tow-limits. A little disappointed that the connecting rod doesn't fit perfectly into the receiver hitch. So, when there is no weight on the ball mount, it is wobbly and makes an annoying metal-to-metal clinking noise whenever you go over a ditch. You can easily correct it with a piece of cardboard stuffing for cushioning or just take it off when not it use. Great piece of equipment, works perfectly! Super happy with the purchase.

This starter kit was exactly the size I needed for the hitch on my Trailblazer, and has held up beautifully this past year. I'm confident it will last for the lifetime of the vehicle.

The hitch and ball mount are excellent quality. My concerns are twofold. The hitch is so heavy that I had to take it to my mechanic to have it installed. Minor cost and inconvenience, but the hitch for my previous F-150 was just as sturdy, but easy to install myself (albeit with higher ground clearance). My concern about the ball mount is that the factory told me erroneously that it could not be reversed for a drop, so I returned it. This order is for the replacement after I was finally correctly told it could be reversed and how to do that. Ball mount would have been a 3 for that reason, and overall hitch and ball mount quality a 5. So I averaged them.

I have two of these. My first I bought two years ago. I very highly recommend this Curt Class III Ballmount 2" Drop because of its price, durability and quality. I towed various class 3 loads with ease and confidence with this ballmount. It slides into the hitch and does its job without fail. It looks excellent after towing a load. etrailer's price is about as good as it gets and delivery is very speedy.

We sold our small motor home and purchased a small travel trailer. This hitch provided a perfect solution to how to use our bike rack while towing the trailer. It even allows room for the pickup tailgate to be lowered without removing the bikes from the rack. The hitch is very hefty with a high weight limit - plenty for the GVW of the trailer (7,000#) plus 125# of rack and bikes.

This has been an amazing multipurpose ball mount. We purchased this to use with our Hollywood Bike Rack and also to connect onto our boat. We weren't sure if this would work, but it was awesome. It is very well built and We had to make some minor adjustments to the position of our boat on the trailer so the turning radius of the bike rack that was attached would clear the truck. This is very well made and solid.

The welding splatter found its way to the hitch pin hole and it took me some time with a Dremel to clean it out so the hitch pin would slide in.

Each edge of the hitch receiver shipping carton was pierced by mounting brackets, but no damage fortunately. Consider adding another layer of cardboard padding?

Very pleased with etrailer. Very easy to order from website. Fast delivery, easy to install ,perfect fit . Thanks. .

Perfect fit for 2 inch Draw Tite receiver. good price, fast shipping.

Great product. Fit and finish is excellent. I've mounted the Curt 1 1/4" hitch to my 2007 Mazdaspeed3. Taking the rear bumper off, which only took 30 minutes (maybe a few minutes more than that) made it very easy to attach the Curt hitch to the car. I wanted to compliment the Mazdaspeed3's overall appearance, so, I decided to go with the Curt euro ball mount 11 3/4" . Very pleased with the outcome.

This worked out to be the perfect ball and mount for my purpose- occasionally having to use my car to tow my utility trailer. I got this and the DrawTite receiver hitch for my '99 Monte Carlo and everything went together in less time than the estimated time that had been shown. Very happy with both purchases!

Perfectly as described, Box was a heavy hitch and the box must have been damaged in shipping so it was a little delayed. You can't mess up a forged hitch it still is in excellent condition.

I bought this to use it for the 3 inch rise it provided. I have a lowered truck and towing my car carrier would prove to be difficult at times. The 3 inch raised that this provided made the trailer stay in a more manageable position. The heavy solid metal construction is of extremely high-quality. I would not have any hesitation towing something at the rated 16,000 pound capacity.