Best 2023 Ford F-150 Trailer Hitch Ball Mounts

To be honest, I use it upside down. I needed a hitch with rise, but none were available at time of purchase, and yours, inverted, works perfectly! The welds are regularly checked and remain all secure. It's a good hitch.

Working in the sand and grass of my driveway my wife and I installed our new etrailer receiver hitch. Great fit and finish! Went right on as described in the online guide. Hitch required a spacer washer on top back bolt attachment point. Taped it on so it would not move while lifting in place and it stayed right there! Used a car jack to raise up and hold the hitch into the underside of the trunk tighten the bolts and reattached the tail pipe done. Now we can pull our Sunfish Sailboat any where the car will go.

Strong and seems to be well made and well finished. One-inch ball mounting hole. I used this for a Curt hitch mounted on a 2014 Forester and pulls a small Harbor Freight trailer. Perfect height and trailer is level. Warning - don't get their hitch pin, it does not have a hole for a cotter pin, only a weak clip that I would not trust.

I searched the internet to put a hitch on my 2016 Chevy Equinox and found an instructional video from eTrailer.com where they installed on my exact car. I decided to go with eTrailer.com because they answered all my questions and because of the video-I support businesses that go the extra mile with these videos. Shipping was quick and well tracked, however, the box was flimsy and the one end of the hitch had come out of the box side and the ball mount could have easily come out of that hole during shipping. If I were eTrailer.com I'd charge an extra couple of bucks for more sturdy boxes-people will still buy as eTrailer is a well-trusted brand and this would overcome a lot of the negative reviews you'll see on their site about this shipping issue in their own reviews :-) I installed the hitch by myself (definitely recommend help as two people holding it up to the frame makes attaching 100% easier) in about 45 minutes total (out of the box, read instructions, review video again and installation complete). All hardware went on with no issues. Great quality hitch! I also bought the lesser expensive wiring assembly because most recent equinox's come hitch ready with pre-wired assembly in the left side compartment-snap and done. Picked up a new trailer at Home Depot within days and drove 5 feet and the clacking was horrible. I had always had a welded hitch before buying a hitch that took a ball mount. I really thought something was wrong and when I searched the internet that night it turns out this is very common. However, all you need is some sort of hitch "silencing" device. The number of options will drive you mad but I went with the Roadmaster Quiet Hitch and it did the trick for much less than most of the other options. If I were eTrailer.com I'd have that as one of the RECOMMENDED add-ons and explanation why its super-worthy when customers are buying a hitch. Would have saved me the time and hassle of dealing with it later and the extra shipping charge for buying after the fact when I got free shipping for the other items the first time :-) All in all, I'm super, super happy with my hitch, wiring assembly, ball mount, ball mount locking pin and the hitch silencer. Buy with confidence from eTrailer.com Paul R., Syracuse, NY

Fits our VW Touareg perfectly and allows us to tow a variety of things now. As can be seen in the pictures the hitch has a +5-inch gap between the bumper and the vertical adjustment pillar and the trailer itself is out further so there's enough room to get to the rear hatch and maneuver the vehicle/trailer.

I needed a hitch that I could haul my work trailer with and still drop the tailgate without dropping the trailer. I looked on etrailer and found one that would work barely but decided to call etrailer and see if anyone had any ideas. Steve answered and looked after I told him my requirements and came up with this. This has a longer distance from ball to pin by a few inches compared to the one I found so my tailgate will still drop even if I’m at an angle to my trailer or on a hill. Also with the adjustable height it’s great. Awesome hitch. Solid for a good price. ??

The hitch and ball mount are excellent quality. My concerns are twofold. The hitch is so heavy that I had to take it to my mechanic to have it installed. Minor cost and inconvenience, but the hitch for my previous F-150 was just as sturdy, but easy to install myself (albeit with higher ground clearance). My concern about the ball mount is that the factory told me erroneously that it could not be reversed for a drop, so I returned it. This order is for the replacement after I was finally correctly told it could be reversed and how to do that. Ball mount would have been a 3 for that reason, and overall hitch and ball mount quality a 5. So I averaged them.

I have two of these. My first I bought two years ago. I very highly recommend this Curt Class III Ballmount 2" Drop because of its price, durability and quality. I towed various class 3 loads with ease and confidence with this ballmount. It slides into the hitch and does its job without fail. It looks excellent after towing a load. etrailer's price is about as good as it gets and delivery is very speedy.

I've used the hitch over the last year on several trailers and loads. The adjustability made towing a much better feel and ride over a fixed hitch that at times not the greatest. I see no wear, very easy to adjust even once coupled to the trailer and finding the trailer needs to be leveled better.

Works flawlessly. I was very excited the day I got home and my Rapid hitch was on the front porch. It came in nice box and was packaged very well. I opened it up and unpacked my rapid hitch and I was very impressed with the quality and precision of this hitch. All of the machining was PERFECT and everything fit together right. I put it in my truck right away. Going down the road with the trailer on and off there is absolutely no rattles, clunks, or jolts. I also love how everything is aluminum or stainless steel, NO RUST. I wish I could've gotten the greaseless model but my boat is too heavy. My only complaint is that it doesn't come with locking pins. With a hitch this expensive I really wish it came with them. Do yourself a favor and order them with your rapid hitch so you don't have to pay for shipping in the future. Other than that great product and I believe it will outlast me.

My usage of your hitch is a bit unusual, I think. I pull a two ton roller with my Ram and I've used your cushioned hitch to smooth out the process. The roller Lunette just dropped over a 2" ball and then banged and jerked on the ball neck. Check out the photos for my adaptation.. I can flip it over and use the 2" ball! Have enclosed some photos. The cushion is holding up very well and it takes a beating!! Thanks

We have a Pink Tractor (google Mom's Pink Tractor) that we pull to events, mainly in Ks, Ok, Mo, and Ne. We have around 35 events a year we take the tractor to to promote breast cancer awareness. The other day my wife and I were leaving for an event, i had let a friend borrow the hitch to see how he liked it. In less then a mile from the house my wife started complaining about the trailer jerking. That is coming from a lady that really was upset when I paid that much for a hitch. She told me to stop and buy one. (a long and expensive trip, we had to stop at a casino so she could rest her neck) I could write a review with a lot of trailer talk, but, this story tells the story.

Sturdy and feels strong / heavy. Love it, except for the part when I forget it is behind the van and run into it :)) Not pleasant. Easy to install and the drop is just right for my trailer. Before I used to have to raise the tongue all the way to the top of the jack, now it feels like it is just there. The trailer seems to be well balanced now.

After balking at the cost to have an auto-shop add a trailer to our Toyota Highlander, we found etrailer.com and decided to take a chance. The "how to" videos factored considerably in our decision to buy ... they made it look so easy! And surprise! It really -WAS- that easy. We used standard block-type ramps (the kind you can buy for $40 ) to get the SUV up off the ground high enough to get underneath to do the work. Everything came off as easy as it was showed in the videos. Other than the fact this bar is a heavy so we had our teen daughter help hold it steady while we bolted it into place (i.e., get help for when you go to lift it), it went super smooth. Thanks for saving us $280 over the cost the car dealer quoted us! P.S. - be sure to watch the linked videos so you get the right trailer lighting attachment and ball hitch for your new hitch.

Super hitch. Best money spent for towing so far. Prompt shipping and a pleasure to buy from this vendor! Thrilled with my experience and will look here for all my trailer and towing needs.

Love these hitches. This is my second one. Honestly, it will save you money. One month a few years ago, I spent $300 on hitches because I would forget or did not have the right height, ball, etc. finally bought a b/w and never had a problem again. I bought this one because I got a new truck with 2" receiver. Great quality, simple, reliable.

Easy to use. Stows away to avoid bumping knees. Would have given 5 stars but it’s expensive. I would still recommend.

I purchased the B&W Tow & Stow 3-Ball Mount - 2" Hitch - 3" Drop, 3-1/2" Rise - 10K - Black and am extremely happy with it. It was $100 cheaper than anywhere else I shopped. Was delivered quickly and was an easy install. I used it to haul a trailer full of wood that I cut up and it got the job done! It is very heavy duty and takes the place of multiple single hitches. It’s nice to have all the options in one.

Works as it should. I enjoy not having to hunt for different hitches when switching trailers. So far no rust..

Works great, very easy to adjust. Keep a rag near to wipe off grease when handling pins and any covering balls for winter rust prevention. Only issue is when using 2" ball in the lowest position,the 2 5/16" ball opposite hags bellow hitch body and scrapes the ball on pitched driveways with low drop gate trailers

The 5” B&W has worked great for me. This year I’ve towed an 18 foot speed boat, a 21 foot family boat, and a travel trailer. Used 3 different heights on hitch to accommodate each trailer, including the larger ball for the travel trailer. When all done, I use the stow feature too. No more hitting shins on the hitch! Quality unit, very happy with its versatility and solid craftsmanship.

Great heavy dury hitch for towing. Less noise than other hitches and does a great job pulling my boat. Love the easy adjusting to height based on terrain where you may need to change this. Worth every dollar and likely a hitch for life.

A small shipping glitch , but they took care of it quickly

I had a great experience ordering from you. Your organization kept me completely up to date with the order & shipping process and delivered the exact products I ordered. Attached is a photo of the 16,000 lbs capacity hitch and 30,000 lbs 2 5/16 ball you sold me in use. The boat and trailer total about 12,000 pounds. Thanks again.

Perfectly as described, Box was a heavy hitch and the box must have been damaged in shipping so it was a little delayed. You can't mess up a forged hitch it still is in excellent condition.

I bought this to use it for the 3 inch rise it provided. I have a lowered truck and towing my car carrier would prove to be difficult at times. The 3 inch raised that this provided made the trailer stay in a more manageable position. The heavy solid metal construction is of extremely high-quality. I would not have any hesitation towing something at the rated 16,000 pound capacity.

Everything, when I need something for my truck I always turn to etrailer. They make it so easy to get the product you are looking for. The quality of their product and the Customer service are the BEST! Thank you.

Great solid forged Ball mount!

Love these. This is my third one. Wouldnt pull a trailer with anything else. Trannys are expensive.

As a full-time RVer, e-shopping is very important for us. etrailer was the right place to shop. Right product, delivered on-time for a great price. You beat the local discount RV store by $25 including shipping. At the same time, I had another outfit send me a clearly inferior product to the one they displayed. Said they would e-mail a pre-paid shipping label for the return (didn't) and tried to put the blame on Amazon. Thanks etrailer for a great experience !

First of all, the products you find at etrailer are not your garden variety, home depot kind of fair. Much higher quality and grade/weight ratings. So to be able to get hard to find items and then by orderring at least 100$ worth of stuff also get it delivered free in 4 days, is awesome. The prices are incredible too.

My 2018 F350 chassis cab has a Knapheide service body with a Buyers hitch installed by Knapheide. It is bolted and welded in place. Unfortunately, it only has a 2" receiver. To have them change to the 2.5" receiver hitch would cost me approximately $1200. The 20,000 lb. Curt replacement hitch would not work on this truck with this bed. The Buyer's hitch has a weight rating of 16,000 lbs. and 1600 lb. tongue weight. Fortunately, Curt has come through again for me with this ball mount. I bought two: one for my 2" ball and one for my 2-5/16" ball. They are great and the drop is very close to what would be perfect. Your towing set-up is only as strong as your weakest link and I now know the the ball mount is definitely not my weakest link. One note to Curt: When you put the stickers on your ball mounts, make sure they're clean. Before I even towed, the thick Curt sticker on both ball mounts started coming off. It feels like there is some kind of coating possibly on the mount and then the decals were applied. I tried pressing them both back on but I doubt they'll last the rest of the week. But as always, Curt has built me a great product for my needs. I'm a one man landscaper business but have spent quite a bit on Curt hitch products because they WORK.

Product is awesome. Shipping container was destroyed when it arrived. Product was not hurt.

Good product

This is a great all-purpose hitch. I've used it to mount a heavy-duty bike rack and a steel T-rack to carry a canoe as well as lumber. Most recently I hauled 5 x 8 cargo trailers full of plants, then furniture for a 600-mile move. It was simple to use, problem free, very strong and sturdy. Now that I live on some acreage, I see a trailer in my future, so this will get a lot more use. I drive a 2013 Tacoma, so this is a good size hitch at a good price with sufficient capacity for my needs. I do use a key lock for the hitch as well.

I actually got my hitch the date they said it would be here to my surprise. When the box arrived it was pretty much beat up, not the hitch just the box. I wished there was instructions how to install it. Overall very satisfied and will buy from 5hem again

I like the look of this set very much and it is easy to mount and adjust the ball mount. The workmanship and finish are beautiful. Customer service was excellent in assuring I found the correct mount for my Ford Escape. I pull my 6'x10' utility trailer or very seldom my pontoon trailer. I like that the adjustable mount comes off very easily as I remove it until I need it while my vehicle is in the garage--it helps prevent knocking your leg against it in the garage. However, I am not having any luck loosening the bolt that secures the 2 chrome balls to the adjustable ball mount; I have the correct Allen wrench but cannot exert sufficient torque to loosen the bolt while the adjustable ball holder is off the ball mount. I want to put a different ball combination on so I can pull my son's trailer, which has a smaller ball than comes with the set, if I have to. I also added the anti-rattle device and it stops the mount completely.

This still looks good with no slop easy to switch between the different ball.

Excellent product! With the three different ball sizes, this tri-ball mount gives you a lot of flexibility. Gone are the days of having several different ball mounts to fit different tongues. High quality construction makes this an excellent investment.

This item should solve the problem I have had with a stainless 3-way ball when I tried to reverse the position on the ball mount. The threads galled between the hex nut and hitch ball.