# 1
Brophy Cable Camper Jacks - 67" Max Lift Height - 3,000 lbs - Qty 2
Great directions for manual assembly, quality metal and parts. Solid and exactly the heavy duty I was looking for to use with my slide in truck camper.
The Brophy jacks were strong, stable, easy to position, and easy to lift and lower my camper. it is a much better method than having four jacks to maneuver. And it cut down my time to 30 minutes total to load my camper instead of an hour and a half! I have to start from my garage and winch my camper down on a cart to the street face because of the incline driveway is so dramatic and my camper won’t fit in my garage if it is attached to the truck. I couldn’t be more happy they were great and now I have my truck loaded with my very modern camper and I’m enjoying quite the holiday! I’m using the 3 ton 67 inch trophy jacks and I’m lifting an 800 pound gross camper. The stability is outstanding.
# 2
Ultra-Fab Ultra Scissor Jacks - 24" Lift - 13,000 lbs - Qty 2
Definitely a heavier duty version of our campers stock stabilizers. They bolted right up to the brackets and glad we have new stabilizers. I hope the paint lasts on these as that seems to be an issue with the other, cheaper stabilizers. Time will tell.
if I had to rate this upgrade in difficulty one being the easiest five being the hardest, it would be a one. Super simple. Take the nuts and bolts off your old hardware and install the upgrade in its place. I read some of the reviews were people were annoyed with the counter clockwise rotation and the bolt sticking out too far. I really didn’t see a problem with either. I know you’re not supposed to use a drill to extend and retract these but I always have. I suppose as long as you’re not torquing the heck out of the adjustment screw you shouldn’t have any problems. I always put a small flat 2 x 6 piece of wood under the foot of each one of these. It seems to add quite a bit of stability.
# 3
Landing Gear Set w/ Handle - 36-1/2" Lift - 8,000 lbs
The product itself was great. It fit right in to the brackets from our old landing gear. We were able to use our existing motor as a cross fit with this gear. The gear box was even better than Lipperts as it was not plastic. The only issue we had with this was shipping. We ordered the part same day as our water pump because we were told it was in stock. Low and behold they changed ship date numerous times, with the excuse it was not easy to pick. Anyhow, two weeks later we finally got the part we ordered.
I have a 2000 komfort 26FS. It has original landing gear that was made by Atwood.Parts to repair are apparently no longer available. Did alot of research and this kit seemed to be a good replacement. It is a exact replacement. Took some time to get it installed as my 5th wheel has a wall and frame right next to landing gear. Original motor bolted up with replacement of original screws which were half inch to short. Four days to get delivered to Oregon. I would have given a five star review but I was missing square tubing that runs from gear box to other leg. Tubing is clearly pictured in discription photos.
# 4
Leveling Scissor Jack Set - 24" Lift - 10,000 lbs - QTY 2
work very well for portable leveling couldn't fix too Jayco Melbourne any where under RV. Still trying to figure a spot.
Received shipment next day after ordering...no added charges. Shipping package arrived in excellent condition. Scissor jacks look good and work smoothly.
# 5
Landing Gear Set - 36-1/2" Lift - 8,000 lbs
Perfect replacement, works great, excellent shipping time and service. Just wish I had got the electric motor that goes with the legs.
Ordered this from etrailer instead of other sites as I knew the shipping would be faster. Sure enough I got the item in 4 days on Thursday and Installed it on Sunday. Very quick and easy. Took longer to get all my tools and set up items together than the actual work. The item was a exact fit with installation being feeding the legs through the holes in the floor down from the inside and installing the 4 clamping bolts to hold them in, the gear box on the lead leg and the cross bar and motor. Now it purrs like a kitten when activated instead of clanking and creaking and blowing fuses. Actual install time was probably 1.5 hours taking my time and injecting extra grease into the gears and lead screw. These replacement units have a grease fitting for both which is great and should allow them to last forever! Being a safety freak I used a 3 ton jack with a 4X6 placed long ways to catch the I beams under the trailer then placed 3 ton car jacks under the frame also and for extra safety backed my truck bed under the tongue for extra security while I worked. The price was crazy great, the fit was excellent and the shipping was fast as usual. less money in parts and 2 hours of work probably easily saved me a grand over taking it to a RV repair shop! Thanks etrailer. Saved me again!
# 6
Ultra-Fab Ultra Scissor Jacks - 30" Lift - 13,000 lbs - Qty 2
Didn’t last 3 months the end came off and screw mess up where the jack don’t work anymore
Worked beautifully for a Replacement for our customer
# 7
Ultra-Fab Stackable Stabilizers for Small Trailers and Campers - 6,000 lbs - Qty 2
Perfect for the four corner supports of our Jayco 175 RD. Much easier to deal with than the scissor jacks installed on the camper. E trailer got them to us quickly as usual!
Our camper came with stabilizers only in the back. Once we level it we put these under the front corners and it gets rid of any movement in the camper like you get when front is only on tongue jack.
# 8
Lippert Electric Landing Gear Set - Weld On - 37" Lift - 6,000 lbs
Received the Kit in about four days (5 Stars for etrailer). The shipping container was severely damaged (2 stars for UPS), but at least it arrived. Did not appear any parts were missing. I ordered this kit because it was less expensive for the complete kit then to replace both landing gear legs separately. I left the 5th wheel attached to the truck and removed the old landing gear, gearbox, and motor prior to the arrival of the new system. Keep all your parts. The new kit arrived and was very easy and straight forward to install. However the tubular steel expansion rod that connects both landing gear legs was too short. I had to use the my old connection rod. Also the spacer used for the inside of the large side of the connection rod was not included with the kit. Had to use the old spacer in the old connecting rod. I used my old landing gear foot plates and pull pins on both landing gear leg extensions. Once installed, the kit worked flawlessly. I placed red marker tape on the landing gear extensions so not to top out the legs when lifting. Again save all your old parts.
I installed the jacks on my 23 ft. 5th wheel trailer, which was very simple and ran the electric wires direct to my battery compartment. The jacks work fine but are a bit too noisy for my liking. Not sure if all are this noisy but they do the job.
# 9
Lippert Scissor Stabilizer Jacks with Handle - 30" Lift - 10,000 lbs - Qty 2
Deception in advertisin It may be my fault for not reading to total description in detail rather than glancing over it. Similar products from other companies list the weight capacity as each but this product lists the 10,000 pound weight capacity as both. They are only good for 5000 each. The [online] option was at least 6000 pounds! The only reason they were not returned is the 30in capability.
These worked out great easy to install with the circular mounting plate.
# 10
Brophy Cable Camper Jacks - 57" Max Lift Height - 1,000 lbs - Qty 2
Great product! I was not looking forward to paying $2G for the standard jacks, then having to bolt them onto the camper. Simple, yet effective! Brophy cable camper jacks are absolutely perfect for the camper I have.
Horribly packaged. Haven’t had a chance to check but I'm sure parts are missing.
# 11
Ultra-Fab Slide-Out Supports for Motor Homes - 16" to 28" - Qty 2
We had so much trouble with the heavy slide out on our travel trailer going out of adjustment .. The trailer spent more time the first two years in the dealership shop or another rv shop than we had it at home.. When we finally got it repaired for the last time my wife checked the internet and found these slide out supports.. We use these everytime we open the slide out at home or camping in the forest or rv park .. And we havent had anymore trouble .. Wish we found these two years earlier .. Thank You fir a great product ..
So love the product and easy to use/install. This length worked great for my slide out. Installed them today and seem to steady up the slide out. Only issue I found was that when I opened the package, one of the u-shaped brackets was bent. But nothing that a little hammering couldn’t fix. Maybe improve the ends of the packaging to better support the u-shaped parts would be my suggestion.
# 12
Stromberg Carlson Electric Landing Gear Set - Weld On - 34-7/8" Lift - 5,500 lbs
Product was an exact fit for my application only problem I had was key inside gear box fell out but easily fixed once I figured it out.etrailer was spot on helping me find correct jack for my ca.per works great
I thought replacing the landing gear would be much harder on my 5th wheel but they when in without a problem and are still working great. The video walks you through the installation step by step. Rick
# 13
Bulldog Tandem Landing Gear Set - Drop Leg - 36" Lift - 8,000 lbs
Delivery was on time, but the box it arrived in didn’t fair we’ll and parts were hanging out of the box! But everything was accounted for and the parts were well wrapped. Installation was very easy. The only issue was the locking pins mount plate is tack welded to the primary leg that the motor moves up and down. Those mounting plates had to be removed to install the lead and follow jacks. A grinder made short work of that. I didn’t put the mounting plates back on, instead I used my spring loaded pins that were on the old legs, they were still in good working condition. Also I didn’t use the adjustable cross over rod that came in the package . I opted to use the one that was on my old jacks, it was constructed of heaven gauge tubing and didn’t have a much (slop) movement in it. Also did not use the plastic housing gear box, I purchased a aluminum house gear box from e-trailer a few months back and used that one keeping the plastic for a spare. Very satisfied.
The leg pin came out because of the design, it is not a strong locking mechanism to not pull it all the way out. (My wife pulled it all the way out) Afyer furthet inspection, in addition to poor locking mechanism, the size of the pin is not adequate for the specified weight of the jack.
# 14
Stromberg Carlson Electric Landing Gear Set - Weld On - 34-7/8" Lift - 6,500 lbs
Great jacks and great fit, however the motor already went out not sure why just quit.
Let me start by saying this review is about the product, not e-trailer. etrailer is great. I love doing business with them. Their prices beat anybody, and the free and FAST shipping is a bonus. Now to the review of the LG-3 landing gear. The pros of this product are they are a direct replacement for the Lippert system on my trailer. No cutting, drilling or welding. They fit in the original brackets. I installed them while camping in about 2 hours with simple hand tools. The cons are they are a direct replacement for the Lippert system on my trailer. They use the same weak motor, that struggles to lift my trailer. The kit was missing bolts and pins and I had to use my old hardware until I could get back to town to buy new hardware. I wanted to go with the Bulldog 10K system, but wanted something that work with my Lippert remote system. The original system failed. I suspect this one will too. Next time I will go with something heavy enough to do the job. Check out the before and after pics and the pic of what can happen when your jacks fail and you have to resort to using hydraulic jacks to lift your trailer. A $4000.00 repair that could have been much worse.
# 15
Stallion Stabilizer Jacks - 7" Drop Leg Travel - 22-1/4" - Qty 2
I mounted this Stabilizers Jacks to the back of a 4x8 utility trailer. I use the trailer to haul my Honda ATV to MotoAmerica motorcycle races. Once the ATV is removed I lower the jacks and mount my tent inside the trailer. These stabilizers allow me to safely move around in the tent without fear of the trailer tipping.
Jacks worked great. Added them to an aluminum 2 place enclosed snowmobile trailer that did NOT like humans to walk up the rear ramp when unhooked and empty!? ...problem solved.
# 16
Ultra-Fab Slide-Out Supports for Motor Homes - 26" to 47" - Qty 2
Great product. Easy to work with and levels the slide so no dropping when extended.
These work great to support the slides on our trailer. I had to manufacture blocks to drop down into the saddle because the slide rails are covered up. We insert them under the edge of the slide frame, and they work just fine.
What our customers are saying:
"very easy to shop"