You're right, the mounting bracket is unique (in a good way) for the Curt TriFlex NEXT Trailer Brake Controller # C24VV.
The bracket is smaller and all you do is put the included adhesive tape on the bracket and stick it wherever you like under your dash. Screws are also included and you can use them with the adhesive to mount the bracket under your dash. Then you'll simply slide in the TriFlex NEXT controller and that's it.
This type of bracket takes up less space than the normal U-shaped... view full answer...
I'd be happy to help you with that.
For starters, the # F008584-2 fenders you'd looked at are designed for 14 inch wheels, you'd be better served going with the # F008585-2 which are designed for 15 inch wheels like the ones you have.
You'll need two sets of # PF1135-BKT-2 mounting brackets that use u-bolts to mount to the trailer frame. The u-bolts you need would need to be tall and wide enough to fit around the frame member of your trailer.
I'll provide a photo that'll give you an... view full answer...
I've attached the installation instructions for the Progressive Dynamics Pure Sine Wave Inverter w/ Transfer Switch - Remote - 2,000 Watts - 12V # PD64FR for you below. view full answer...
The four wires in the picture of the 12V RV Ceiling Fan w/ Wall Switch # 344410TSDC42BNBK you referenced are coming from the wall remote # 344410TSSW12V. You'll wire the wall remote in the following manner:
White: Fan Motor +
Blue: Fan Motor -
Black: Trailer Battery -
Red: Trailer Battery + view full answer...
The correct height setting is going to vary by trailer but you can get there taking some measurements.
First make sure your trailer is on level ground and then measure from the ground up to the bottom of the king pin. Then on your truck take a measurement from the ground to the truck bed floor where the hitch will sit. The difference in these two measurements will give you the hitch height so that the trailer is level.
Next take a couple measurements to see what kind of bed rail clearance... view full answer...
I have a great demonstration video that shows exactly what to do! Our expert Jon walks you through how to turn the bottom hooks of the FullBack 2 # Y02634 into the "anchor mode" at the attached video at timestamp 3:25. You simply flip the hook around and thread the strap through the unused opening to crate a clamp to fit into the trunk. view full answer...
The HydraStar Marine Electric Over Hydraulic Actuator w/ Breakaway and 7-Way RV Harness item # HS381-9067 is designed to work with an aftermarket electric over hydraulic brake controller.
The HydraStar Vented Marine Electric Over Hydraulic Actuator for Disc Brakes - OEM item # HS481-8067 will allow you to use a OEM brake controller to operate the trailer brakes.
If your vehicle has an aftermarket brake controller you will want item # HS381-9067. If you have a vehicle that came from the... view full answer...
The Replacement MaxxFan Plus 4-Speed Roof Vent with White Lid # MA00-04751KSX is meant to be a direct replacement however not all the necessary hardware is included.
The remaining items you'll need is the Key Wall Control part # MA00A03550K, Ceiling Garnish part # MA54FR, RJ11 Communication Cable part # 34279523, and the Roof Vent Installation Kit part # 344270KITW.
Included is a picture of where you'll find the RJ-11 and RJ-45 connection points on the MaxxFan Plus 4-Speed Roof Vent... view full answer...
Yes, the Air Distribution Box w/ Wall-Mounted Thermostat for Advent Air RV Air Conditioners # ACRG15 is what you need for your application. This includes a new thermostat as well.
According to my research all of the wiring for your current thermostat goes directly to the relay box. Since this unit comes with a new relay box that only requires the 4 wires you won't be using your old wiring.
Attached is a wiring diagram another one of our experts has for the # ACRG15 that you can use for... view full answer...
We get this question a lot. The momentary push button on your Lippert LINC system that you need to press to program the Remote Control # LC292614 is not on the remote, but rather on the LINC receiver box which is usually located near the generator. After you press and hold this button on the receiver you will press the light bulb button on the remote until you hear a relay in the receiver click, then release that button on the receiver. The two should now be synced.
I have atttached further... view full answer...
Yes, the Curt hitch part # C77ZV is a fit for the 2023 Toyota Crown Hybrid. I attached a link to the install instructions as well as a link to an installer finder in case you wanted to find someone near you to install the hitch. view full answer...
The Progressive Dynamics Pure Sine Wave Inverter w/ Transfer Switch - Remote - 2,000 Watts - 12V Item # PD64FR will pull DC current from your battery and convert it to AC current for when you aren't hooked up to shore or generator power. The integrated transfer switch automatically changes from inverter to shore power when you hook up at the campground so you won't have to turn your converter on and off. If you look at the attached instruction manual you'll see how to wire the inverter... view full answer...
It sounds like you may already have a 4 way connector on your vehicle, which is half of the battle. In order to operate the Curt Echo Mobile Wireless Brake Controller # C51180 you will need an almost fully functional 7 way connector; using something like the Hopkins # 37185 adapter from the answer you were looking at would work, but it doesn't come with all of the wiring you'll need so I don't recommend using that and you will need to run a power wire to your battery (not included).
Instead,... view full answer...
The Reese Elite Series under bed puck system, part # RP87FR is compatible with your 2017 Ford F250. The puck spacing is identical to hat of the Ford OEM system, so you'd be able to use any puck mounted hitch designed for the Ford OEM tow/prep package puck system.
As you can see by clicking the provided instruction link, the bed will indeed need to be removed temporarily for the installation of the rail kit. Also, if the inner brackets shown in figure # 4 aren't welded to the truck frame,... view full answer...
Dexter brake assemblies like the part # 23-458-459 are essentially the best ones on the market. They use the best materials and and incredibly reliable and well-made.
That being said the etrailer.com brand assemblies part # AKEBRK-7-SA are also very well made too. We have sold a ton of these and gotten very positive feedback on how well they well they work and how reliable they are. If it was my money I would go with these unless you want to have the absolute nicest materials money can... view full answer...
118824 is Tekonsha's part number for The T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # TK69FR. We do not currently have an installation video for this wiring harness, but I can certainly help you out with this process. The harness has a connector that will plug into the trailer light connector in the trunk of your 2021 Toyota sienna; you will likely need to remove the trim panels and side cover to gain access to this connector. You will then need to connect the white... view full answer...
Yes, the engine on your Chevrolet Equinox will need to be run at times when flat towing. The easiest way to determine what needs to be done to flat tow your Equinox is to consult your owners manual.
I went ahead and took a look at the owners manual for both the 2021 and 2022 Chevrolet Equinox. For either model year, you will need to run the vehicle at the beginning of each day and at each RV fuel stop for about 5 minutes. This will ensure proper lubrication of the transmission components.
I... view full answer...
I do have an option for you but SuperSprings does not offer any additional spacers for the SumoSprings Trailer Helper Springs part # SS26MV. That said, we do still have spacers that will work for this, the Timbren Spacer part # A25723-90AH00 for 1" or part # TA25722-90P00. These won't be the exact same as the ones that came with this kit but they will still work well.
In regards to the carriage bolts, you'll need to source this locally from a hardware store. view full answer...
I will be happy to explain how to install the shock kit # LC281255. In addition to the instructions below I have also included a picture of the actual instructions.
1. Raise trailer and jack up the axle to release pressure on the springs.
2. Remove old u-bolts and tie plate.
3. Install new tie plate with the longer side facing outward and torque the u-bolts to the specs in the instructions. NOTE: Do NOT reuse old components.
4. Compress the shock and make a mark on the inner shock where... view full answer...
Go To Results