That's a really good question, but the Curt Echo Mobile Trailer Brake Controller # C51180 will absolutely not fall out of the 7-way on your 2019 Hyundai Santa Fe.
There are a couple of reasons for this, starting with the fact that the connection between the controller and 7-way is really tight; you have to give it a good push to make sure it's all the way in the connector.
The other reason has to do with the tab on top of the Echo; part of the tab is silicone-coated to absorb vibration... view full answer...
You will need a few different items to add a 7-way trailer connector to your 2014 Hyundai Santa Fe because Hyundai did not offer a factory connection for a 7-way trailer connector, only for a 4-way.
If your Santa Fe was pre-wired for the factory tow package, then the first item that you will want is the Curt T-Connector Wiring Harness, # C56332. This will add a 4-way flat trailer connector. I have attached an installation video for you to check out.
Next, you will need our Universal... view full answer...
The easiest and most accurate way to determine if your 2015 Hyundai Santa Fe has the factory tow package is to simply run by your local Hyundai dealer with your VIN. With this information they will be able to tell you with certainty whether or not your particular model Santa Fe is equipped with the tow package.
The trailer wiring harnesses available for your Santa Fe do differ in how they install depending on if you have the tow package or not. The Curt T-Connector Vehicle Wiring Harness... view full answer...
The Kat's Heaters Custom Fit Engine Block Heater part # KH11812 for your 2012 Hyundai Genesis 3.8L V6 will install on the right hand (Passengers) side of the engine in the rear most (Closest To Firewall) plug.
Don't forget to use the Kat's Heaters Plug Cover part # KH28405 to prevent dirt and debris from getting inside the connector while not in use. I have attached an illustration to give you a better idea where the right rear plug is located. view full answer...
The Curt Trailer Hitch # C11303 is designed to fit your 2012 Elantra. The installation instructions are attached you can check out to verify the correct mounting holes. We only offer a Curt hitch for the Touring hatchback as well. That hitch is part # C11471.
I have attached a link to a helpful article that explains how to deal with noise from the exhaust rattling against a trailer hitch.
If you find the trailer hitch is installed using the incorrect holes you can order replacement hardware... view full answer...
Provided that your 2013 Hyundai Santa Fe is a Sport model then you can use harness # 118571. This harness plugs in line with the vehicle tail light wiring so the connection points are located behind each tail light. I have included a link to the installation instructions for you to view. view full answer...
To install the etrailer Trailer Hitch Receiver # e95ZR on your 2023 Hyundai Palisade you will have to do some trimming. This is going to be needed on the underbody panel which attaches to your frame so it will not be seen. I have linked an installation video from an install we did in our shop where you can see where trimming is required. You can see the trimming at the 8:20 mark of the video. view full answer...
I checked with the manufacturer, Kat's, about the Kat's Heaters Custom Fit Engine Block Heater part # KH11812 which is a fit for a 2011 Hyundai Genesis with 3.8L V6 Engine. The correct location is on the right rear "RR" side of the engine as seen in the attached photo. Unfortunately, Kat's does not provide exact step by step instructions for installation. It's possibly removal of existing component is required for installation but that will be up to the discretion of the installer. view full answer...
I have attached an installation video of the # 118258 wiring harness on a 2009 Hyundai Santa Fe for you. The installation is pretty straight forward once you have gained access to the factory connectors.
To do this, you are going to start by lowering the spare tire, and then you would open up the cargo area and remove the access panels, threshold trim, trunk floor panels and trays. Proceed by removing the trim panel on the driver side, but make sure you remove the fastener on the driver... view full answer...
The Adapter 4-Pole to 5-Pole Trailer Wiring Adapter - Shorter # 47515 will connect to your current 4-way wiring harness and you will run the blue wire behind your tail light to connect to the reverse light power wire. The reverse light bulb socket will be fairly obvious as it leads to the clear lens. The Quick-Splice connector makes this easy. I've attached a video to assist. view full answer...
The 4-Pole Trailer Connector and Installation Kit # C59496 comes with a basic circuit tester that has an alligator clip on one end that connects to a ground like the metal frame on your vehicle. Then you will use the sharp point to insert into the wire connection while you run one lighting function at a time. The LED bulb will light to reflect the function it sees on that wire. You can see this in the attached video at the 2:00 mark.
The green wire will connect to the passenger side... view full answer...
The location of the connector for connecting the Curt Wiring Adapter # C77BR on your 2023 Hyundai Santa Fe is under the dash to the left of the steering column. The 4-pin connector is cream colored and should be exposed. Be sure to look and feel around the wiring harness as the connector could be on top of the wiring where it is difficult to see.
I recommend using the Curt Spectrum Trailer Brake Controller # C51170 as it will allow you to locate the control knob where it is most convenient. view full answer...
The reverse lamps for a 2011 CR-V are in the taillight assemblies, not on the liftgate. You can access the wiring harnesses that feed the taillight assemblies by removing the interior panel on either side of the cargo area. Use a circuit tester like part # PTW2993 to probe the wires in the harness, as a helper puts the car in reverse with the engine off. The correct circuit should be hot, so you shouldn't have any trouble finding the correct wire. I don't have any specific information on... view full answer...
Sometimes our customers find better ways to install products we carry like the etrailer hitch part # e95ZR that fits your 2024 Hyundai Palisade. It's perfectly okay to have the bolts reversed like you mentioned. Glad to have back! view full answer...
An inline fuse would be needed to install the Multi Device RV Charging Station # 37215095. If you use 14 gauge wire then you can use a 10 amp fuse and if you use 12 gauge wire you can use a 20 amp fuse. Personally, I would use 12 gauge wire and a 20 amp fuse to protect the wiring and outlet. view full answer...
The etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2" # e95ZR does not require any trimming or modification to your bumper molding or fascia. You will, however, need to remove the passenger side plastic molding temporarily but it can be re-installed right after the receiver is installed. Nothing will look out of the ordinary as you can see in the attached photos.
We do not have an installation video for this exact receiver, but I did attach an installation... view full answer...
When finishing up the installation of your # C98DR you will completely remove the outlined section of the underbody panel. This will leave you with two separate panels to go on either side of the receiver. Make sure you measure 1-1/2" in from each of the mounting holes so you are still able to reattach the panels after trimming. view full answer...
I have attached a screenshot of the installation instructions for the Thule Hullavator item # TH898. When you remove the rubber inside the channel of the Thule WingBar Evo Crossbars item # TH711320 there are square nuts inside. You will adjust these square nuts and the rubber channel however you need to install the Thule Hullavator item # TH898. You won't need the Replacement M6 x 37 mm Screw item # TH97FQ as the Hullavator comes with all necessary parts. view full answer...
Yes the Swagman XTC-2 TILT # S64671 that you referenced can transport bikes with slanted top tubes like you mentioned which are common on womens style bike frames. The hook will slide down pretty far on the mast and secure to the bike frame.
I attached a review video for this rack for you to check out as well. view full answer...
On your 2010 Tuscon with the 2.4L engine, the Kat's Heaters Custom Fit Engine Block Heater, part # KH11812 is installed on the front left of the engine block.
When looking at the engine from the front of the car, the plug is on the front drivers side of the engine. view full answer...
Go To Results