Hey Ian, great to hear from you again!
The differences between the MORryde CRE3000 # MR87ZR and AllTrek 4000 # MR89DR that fit a 33" wheelbase is the height between the hanger and equalizer bolts, and the amount of travel the suspension style will offer.
For the CRE3000 the height distance is 3-1/4" and it can have up to 3" of travel, while the AllTrek 4000 has a 4-1/2" height distance, and it can have up to 4" of travel.
I personally like the CRE3000 a little better so I recommend going... view full answer...
Hey Dusty! There is a lot of information out there right now about Chill Cube. Some of it is definitely confusing, especially when we have people trying to use parts that aren't designed for the new R32 systems. On top of that, the Chill Cube uses a remote which acts as its thermostat and isn't compatible with a furnace.
There are two ways to make everything work together, I will give you both. The first is to get the Furrion Chill Cube RV Air Conditioner w Air Distribution Box - Ducted... view full answer...
Hi John; if you want to use the # PD89RR the 6 gauge won't be enough for the 80 amp output. You will need to switch to 4 gauge copper or 2 gauge aluminum wire. view full answer...
Hey Gary, thanks for reaching out, and thanks for your patience as I looked into this.
I spoke with MouseBlocker directly and they said as long as you're connected to shore power then your best bet is to use the 1000x # MB54FR on the inside of the trailer, and the 360x # MB64FR outside and under the trailer.
Remember that the soundwaves can be blocked by walls and doors, so keep all of your doors open (inside the trailer) and be prepared to adjust things as necessary since each trailer... view full answer...
For your AL-KO T44 axles, the brake assemblies you need are the Dexter Nev-R-Adjust Electric Trailer Brake Kit - 10" - Left and Right Hand Assemblies - 4.4K # K23-478-479 or the manual adjust # K23-462-463-00 along with spoon adjuster # W80630.
The grease seal you want is AL-KO part 568861 which is the Grease Seal - Double Lip - ID 1.719" / OD 2.565" # RG06-050 for a set of 2 seals. view full answer...
Hey Maurice! We no longer recommend swapping out just the AC unit since there have been a lot of compatibility issues. Also, everything is switching to the new R32 refrigerant due to the new 2025 EPA regulations. The old parts for R410A units are already being phased out so it is a good idea to switch so you don't have to replace everything later if something fails.
Sticking with the Advent Air you looked at you can choose from the following:
-Advent Air RV Air Conditioner System - Single... view full answer...
Hi Brian,
To ensure you're getting the correct fit you'll want to measure the spacing horizontally from eyelet to eyelet and vertically from the hanger bolt eyelet down to the center of the shackle strap eyelets on your current equalizer. The equalizers in kit # K71-652-00 have a horizontal measurement of 5-3/4" and vertical measurement of 2".
The included shackle strap kit comes with a 2-1/4" spacing so it wouldn't be the correct fit for your trailer. The most common sizes are 2-1/4"... view full answer...
Hello Rene, thanks for reaching out. It is pretty typical for RV manufacturers to use axles that are not rated for the full GVWR. They say this is because 10%-15% of the camper weight is on the hitch instead of the axles. They will put the bare minimum axle on there to save on costs. Very typical in the RV industry these days sadly.
It is possible to use a higher rated axle. For the 86-1/2" axles we have a 6,000 lb option. We offer it fully loaded with brakes and 6-lug hubs as part #... view full answer...
Thanks for all the information! You are correct that is the lead leg because it is closest to the gear and the motor. However, in order to determine which replacement lead leg you need, you'll need to find the model of the landing gear on your trailer and measure it's outer tube length. This is something we have no way of knowing and I wouldn't want to assume anything.
For example, if you do have a Venture landing gear with legs that measure 29-1/2" you can replace the leg with the Replacement... view full answer...
Hey Chad; since your tandem 3,500 lb axles have a 3" diameter you need the Roadmaster Comfort Ride Leaf Spring Suspension Kit w/ Shock Absorbers # RM-2460-2560. The kit comes with everything you need for installation aside from standard tools.
Also, this system is compatible with the MORryde X-Factor Crossmember # MR33WR you were looking at if you want to add them to the front and rear hangers. The one thing I would do is look at your hangers to make sure there is nothing like plumbing... view full answer...
Your Raptor Toy Hauler likely has a landing gear setup similar to the one you were looking at: Lippert Electric Landing Gear Set - Weld On - 37" Lift - 6,000 lbs # LC333964. If so, then the correct replacement motor would be Lippert Components Tuson High Speed 5th Wheel RV Landing Gear Motor # LC141893 which is rated for 5,000lbs, or you could go with Lippert HD 6500-lbTuson 5th Wheel RV Landing Gear Motor # LC196308 which is rated for 6,500lbs. This is the heaviest duty motor we have for... view full answer...
Since your Progressive Dynamics converter has a dual fan setup the correct replacement would be the Lithium Converter Section part # PD4575LICSV. view full answer...
Kits are not designed to fit specific trailers though based on my research we do have one kit that may work for you, depending on a few measurements you need to take. Based on my research your Lance 2280 travel trailer is a single axle so the Lippert Components Bolt-On Shock Kit # LC281255 may work as it is for single axles that are 2-3/8" in diameter, which is standard for 3,500 lb axles.
So long as you have that diameter axle and a 4 inch clearance between the inside of your trailer's... view full answer...
Hey Shane! The closest axle we have to those dimensions is the Trailer Axle w/ Electric Brakes item # e73SR. It has a 86-1/2" hub face and a spring-center-to-spring-center length of 71-1/2". You may be able to get away with the hub face being slightly longer depending on your fenders but you'll need to use the Spring Seat item # TRSS300 to replace the ones that come with the axle. view full answer...
Michael, so you are correct you do have 4,400 lb axles so you can use the Dexter Nev-R-Adjust Electric Trailer Brakes # K23-478-479 for replacements.
These are self adjusting so you never need to manually adjust them, works with 14", 14 1/2", and 15" wheels, and includes both the left and right hand side.
For hubs we have had customers in the past use # 8-201-5UC3, but you'll want to check your existing bearings and verify that they will work with this hub. view full answer...
We do have the exact bearings, races, and grease seal you need for your 4,400 lb Dexter axle, and while there isn't a single kit with the parts, you can get them all individually. What you will need are the following:
Bearings # L68149 and # LM67048
Races # L68111 and # LM67010
Grease Seals # RG06-050 view full answer...
Since you mentioned that you broke a leaf spring and not the axle, in order to determine which replacement leaf springs you'll need for your 2017 Keystone Bullet Premier Ultra Lite Travel Trailer you will need to measure your current springs from the centers of one spring eye to the other. This distance is going to determine which springs will fit as a replacement. Since we know you have a 3500-lb axle, we can narrow it down a bit.
If your old springs measure roughly 23-1/8" long from... view full answer...
Hi Dale, it looks like you have the resurrected 4,400 lb hubs like # DX53WR with the # L68149 inner and outer bearing. These had been phased out but are making a comeback. You also need # L68111 for the races and 10-19 grease seals # RG06-050. view full answer...
Hey Bob, you'll want to go with the Furrion Chill HE Replacement RV Air Conditioner for Coleman Setup - 15,000 Btu - White # FR42PV. This is specifically for Coleman, Dometic, or Advent distribution systems. view full answer...
Go To Results