Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
6-5/8" x 2-3/16" Oval. Waterproof trailer light serves as either a side marker light or a clearance light. Chrome bezel provides finished look. Surface mount - hardware not included. 2-Wire design with 0.180 male bullets. P2 rated.
Features:
Specs:
The waterproof construction of this light makes it ideal for use on trailers that may be submerged, like a boat trailer. The circuit board is sealed, which means that water will not damage the diodes or circuit board.
A P2-rated light produces a 45-degree angle of light to either side of its centerline for a total of 90 degrees of coverage. This beam pattern can be seen straight on, but it cannot be seen clearly from the side. So this type of light can be used as either a side marker light or a clearance light, but it cannot function as both. If you need both functions, then you must install 2 separate lights on your trailer - one as a front or rear clearance light and one as a side marker light.
California residents: click here
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Today we're going to be taking a look at the Optronics M1 LED clearance or side marker light with the included chrome bezzle. The little trailer light is going to serve as either a side marker light or clearance light. The chrome bezzle is this piece that goes around the light. It just adds a clean, finished look. The unit is sonically sealed so it has a waterproof design when it comes with the housing and the lens unit so it is submersible. Now it's an LED system.
LED's are going to make replacements for incandescent lights. The last much longer, they burn brighter, they're more efficient, and you don't have to worry about replacing bulbs and you don't have to worry about bridle filaments. It's going to feature the amber lens. That's a polycarbonate lens as well as a polycarbonate housing when inaudible 00:00:39 construction. It's a surface mount installation so it mounts on the surface of your trailer but the installation will require a small hole for the wiring to pass through. Your hardware's not included.
It's going to feature two mount holes; one right here and one right here. Remove that bezzle. It just snaps on and off. That's a plastic piece. You can remove that to gain access to the mountable locations from the front. Two wire design; one for power, one for ground.
It does not matter which one you hook up to which function. They're going to be featuring the 0.18 male bullets on them. If you want this for a hardwired application, you can cut those off and then strip the wiring back. This is a P2 rated light. It's SAE and Department of Transportation compliant. Take a look at the overall measurements real quick, starting with the overall length.
Measuring edge to edge, it's going to measure about 6 5/8 of an inch long by 2 and 3/16 of an inch tall and then the thickness. It's really low profile light. It's only going to measure about 5/8 of an inch thick. The mount holds on the unit are separated on center by about 4 and 5/8 of an inch. That's going to contain a total of 4 diodes or 4 LED's and then the power draw of the unit at 12.8 volts is 0.12 amps. We're going to go ahead and hook it up to our external power source that way you can see what it looks like with power running to it. Then we'll also be about to turn off our overhead lights so you can see it in a low light setting. You can see here that the light sends out a night consistent signal. Again, it's going to contain 4 diodes or 4 LED's. The multi diode design really does a great job at optimizing the overall light output of the unit. That's going to do it for today's look at he Optronics M1 LED clearance or side marker light with the included chrome bezzle.
Average Customer Rating: 4.8 out of 5 stars (46 Customer Reviews)
6-5/8" x 2-3/16" Oval. Waterproof trailer light serves as either a side marker light or a clearance light. Chrome bezel provides finished look. Surface mount - hardware not included. 2-Wire design with 0.180 male bullets. P2 rated.
Excellent service
Good cuality
ship quick and fast good price tha nks
I had a good experience with these guys. Price was right and ship time was proper.i do t have anything bad to say.
nice packaging
Good looking and working product. Chrome cover is plastic but should hold up well.
Great Service, Good pricing and Quick Delivery. Thanks for locating the proper part for this older Titanium trailer.
I was wanting the exact light and connector so it would be a easy replacement and it was just what I was looking for Thanks etrailer
This is an excellent product. Top quality!
So much better than lights you buy at your neighborhood auto supply.
Lights up bright with the LED bulbs.
A little higher price than your normal lights but it is well worth the difference.
Highly recommend!
everything is good order is complete
Exactly as described. Lovely bezel. I clipped the connectors and soldered them into my harness.
It's exactly what I ordered and the items I wanted. I don't have them installed yet but looking forward to it. Putting it on the front of my Arctic Fox camper. I have 4 on it now these will complete the job.
Perfect fit, works great
fast service and great product
This is not my first purchase from etrailer. The products I purchased were exactly what I wanted at a very good price. I received my items in a timely fashion as always. I am very satisfied with the service I get when I buy from etrailer, and will give them repeat biusiness.
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Stuart
4/22/2024
Still working great ??