Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
This GloLight Halo LED tail light puts out a crisp, red glow that’s easy to see day or night. The outer halo acts as the tail light, while the center LEDs handle turn and brake functions with instant-response brightness. With 22 diodes drawing just 0.295 amps for the tail light and 0.59 amps for stop and turn at 12.8 volts, it gives you strong, efficient illumination without the high current draw or fragile filaments of old-style bulbs.
If your trailer hits wet roads or gets backed into the water, this light is ready for it. The polycarbonate housing and acrylic lens are sealed to keep out moisture, making it fully waterproof and submersible—ideal for boat trailers or any setup that faces tough weather. You won’t have to worry about water intrusion fogging the lens or corroding the wiring.
Mounting is straightforward thanks to the integrated flange and recessed design. The light measures 7-1/2" wide x 3-5/16" tall x 1-5/16" thick, with a clean face size of 6-7/16" by 2-5/16". The flange gives it a neat fit against the surface without extra brackets, so you get a solid, finished look once installed. Hardware isn’t included, which gives you flexibility in how you mount it.
Moisture can cause real problems at your wiring points, but this GloLight solves that with a weathertight connector built into the back. It’s designed to seal out water and dirt where other plugs fail. It connects using adapter AL45PWTB (sold separately) for 3-prong setups and works with right-angle (A47PB) or straight (A45PB) pigtails if you need them.

This light doesn’t just look good—it meets all required DOT, FMVSS 108, and CMVSS lighting standards. That means it delivers reliable stop, tail, and turn performance that keeps your trailer visible and legally compliant on the road. With LEDs backed by a lifetime warranty, it’s a dependable upgrade that’s built to last.

Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Today we're reviewing part number STL111RFMB from Optronics. This light is in their GLOLight series. It's an LED Stop/Turn/Tail Light with a flange mount. It also has a weatherproof connector. You have a red lens over all the LED lights. You have a band of LEDs that go around in an oval like this.
You have in the center a row of LEDs that will serve as your brake and turn signal lights. I'll show you that in just a moment. This light uses surface mount technology. That protects the LEDs from moisture, shock, and vibration and distributes heat evenly. You have a poly-carbonate mounting flange built in, so that makes the installation very easy. This does require a weatherproof connector.
If you do not already have one, then you will need to get this part, which is sold separately. It's Optronics part number AL45PWTB and it's their three-wire straight plug and weatherproof connector. As you can see, it has a yellow rubber gasket around here that helps to keep it waterproof. You plug it into the back of the light and it has a little clip here that helps to keep it in there securely. As you can see, I'mpulling very tightly and nothing is happening.
You can be assured that that will stay in. The other end, of course, needs a power source. You want to plug that into your standard three-prong plug on your trailer. We have a three-prong plug here that's attached to a portable power source. I'm going to plug it into that. We will turn off the lights and turn on the power.
What you see there is the tail light. Here is your brake light and your turn signal. We can turn the overhead lights back on. This light does meet all the requirements of the Department of Transportation for automotive lighting. It measures 6 1/2 inches left to right, side to side, 2 1/8 inches tall, and it's 1 1/8 inch thick. There's a lifetime warranty on the LEDs and a three year warranty on the housing and the wiring. There you have it for part number STL111RFMB, the Optronics GLOLight LED Stop/Turn/TailLight with a built-in flange mount. .
Customer Satisfaction Score:
97% were satisfied with this product
3% of customers were not satisfied
Ratings & Reviews

Derek P.
7/19/2021
Still great, nice and bright. They are a huge improvement over the factory incandescent signals.
Do you have a question about this Trailer Light?
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.









Mike L.
1/3/2019
The easiest way to troubleshoot a lamp is to quickly swap it for the one on the other side of the rear of the trailer. If the lamp does not function at that point, its a sure bet its defective. If the lamp is defective, the LEDs are covered by a lifetime warranty.