Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Upgrading to LEDs makes a big difference in both brightness and efficiency. Each light in this mini ID kit uses a single red LED that lasts up to 50 times longer than an incandescent bulb. The lights only draw 0.022 amps at 12.8V, giving you bright, clear light with very little power use. With no bulbs or filaments to replace, they stay dependable season after season.
Water damage ends a lot of trailer lights early, but not these. Each light’s housing and clear lens are sonically sealed into one solid unit, keeping moisture from reaching the diodes or wiring. That waterproof design makes them submersible and perfect for trailers that see launch ramps or wet roads. Once installed, you can count on them to keep shining even after a soak.
These PC-rated lights throw out a wide 180-degree beam pattern that’s visible from head-on and from the side. When properly mounted, they can serve as both rear clearance and identification lights, making your trailer more noticeable to other drivers. That extra coverage helps increase safety on the road, especially at night or in low-light conditions.
Each light is just 3/4" in diameter by 7/8" deep, so it fits neatly into tight spaces without sticking out. The included black grommets make recessed mounting straightforward—just cut or use a 3/4" diameter hole, push the light through, and reinstall the grommet to hold it in place. The 29" insulated wiring harness with two molded leads (power and ground) keeps everything neat and easy to wire up for a clean finish.
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Jeff: Hello, everybody. This is Jeff etrailer.com. Today, we're going to take a look at this mini red LED identification light kit for trailers. Now, this trailer light kit will function as rear identification lights for trailers that are over 80 inches wide. Basically, trailers that are over at 80 inches wide, they do require three red identification lights to help define the perimeter of the trailer. Now, these lights are sonically sealed.
They're in a waterproof housing and it makes them submersible. The LEDs are nice because they make great replacements for incandescent lights. They'll last 50 times longer. They're more efficient, they'll provide brighter light with less power output and, of course, no bulbs to replace or brittle filaments to break, and they give you a lifetime warranty on the LEDs. They are durable, polycarbonate lenses and housings.
That is a clear lens you can see, that's over a red LED and these are compatible with 12 volt DC systems.They are a recessed mount, comes with the black grommets right here, and it will require a three quarter inch diameter hole for each light to fit into. It does use a two-wire molded harness, which includes a white ground wire and a black power wire. This is a PC rated light, which produces 180 degree beam pattern, and these are DOT compliant.Again, the application for these are trailers over 80 inches wide. It is for a quantity of three red lights. The lights themselves are three quarter inch diameter and about seven eights of an inch deep.
The harness length on this is about 29 inches and it is one led per light. Power draw at 12.8 volts is 0.022 amps. The last thing I want to do is hook this up to some 12 volt power, just to show you how bright they are. We'll take our two wires, we'll hook up our black power wire, and then we'll hook up our white ground wire. With those both hooked up, you can see the red lights, or LEDs, come on.
I'm going to go ahead and turn off the overhead lights and there you can see, here's your three red LED identification lights. Very bright. Go ahead and turn back on our overhead lights and we'll go ahead and disconnect our power. That should do it for the review on this mini red LED identification light kit for trailers.
Customer Satisfaction Score:
98% were satisfied with this product
2% of customers were not satisfied
Ratings & Reviews
it was all just as advertised.
Perfect fit good bright light easy to i nstall
Nice and bright super easy to install
Great item that you have in stock packaged well arrived perfect.
These little guys are great! Easy to install, way bright, adds a little custom touch.
Excellent sales and knowledgeable empl oyees.
Everything I needed all in one place! Fast shipping.
The marker lights were a great replacem ent.
High quality and fast shipping. Customer service was a joy to work with.
I ordered several different trailer parts from etrailer and the service is good so I won’t order from anyone else. The product is always right
Awsum Little lights have been using these lights for years on all my trucks and trailers never replaced any yet,Thanks etrailer
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Jim
3/17/2022
People are always asking me about these lights. I mounted down behind my tail gate. I used to own big over the road trucks and I was a LED junkie, I had everything led on my trucks as I like bright and long lasting equipment.