Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Tired of bulbs burning out or losing brightness over time? This 3/4" round Uni-Lite uses a single red LED that lasts up to 50 times longer than old incandescent lights. It’s built for efficiency, drawing just 0.052 amps at 12.8V while putting out a bright, clear light through its durable polycarbonate lens. Since there are no fragile filaments or bulbs to replace, you get steady performance and lower power use every time you hook up.
If your trailer ends up in wet conditions, this light is ready for it. The housing and clear lens are sonically sealed into one solid unit, keeping water out completely. That means the LEDs and circuit board stay protected—even when submerged. It’s a dependable choice for trailers that see rain, road spray, or boat ramp launches.
Visibility makes a big difference for safety on the road. This PC-rated light shines with a 180-degree beam spread—90 degrees to either side of center—so it can serve as both a clearance and side marker light when properly mounted. Drivers can see it clearly from the front or side, giving you reliable coverage at night or in low light.
When space is tight, this small round light fits where others can’t. It’s 3/4" in diameter and just 15/16" long, so it tucks in close without sticking out. Installation is simple too—just cut an 11/16" hole for the included black PVC grommet, connect the 2-wire pigtail (power lead and ground), and you’re done. The recessed mount keeps everything neat and secure on the surface.


Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Hey everybody, Ryan here at etrailer. Today we're going to be taking a look at and showing you how to install the Optronics trailer Light led clearance or side marker light. So right away, the first thing I noticed about this light is how bright it's going to be. It's actually really impressive for how big the light itself is. As you can see, even in a well lit room like we're in today, it's going to have no issues to really throw in that light off far for other motors to see. So really kind of puts your mind at ease, knowing that you're lit up.
Now, it kind of separates this one from some of the other types of lights is that this is the trailer Light. So as you can see, that the light is really dispersed evenly throughout the lens. It gives us a nice, solid light, as opposed to some of the other ones where you can kind of see through the lens itself and just see that one led.With this one it gives us a cleaner and more bright appearance. So what I like too, is the size of the light. It's pretty small.
So it's going to give us a lot of different options on where, how you want to mount it up. Works perfect for trailers like you have today. But also a lot of people are starting to put these types of lights on their mud trucks, their off-road vehicles, like side-by-sides for example, golf cards, things of that nature. So even if you want to mount these up on a different type of project, you're going to be able to find a spot to put them.So once we have the light turned off, we're going to have a solid orange lens, which the upside of this is even when the lights are off, you can still see this pretty well in the daylight. Now they do make clear lenses as well, and really no huge difference.
It's going to be kind of your personal preference as far as what you think looks a little bit better, but at the end of the day, a really reliable led light that's going to last a long time and a lot of other people see us.As far as the installation goes, it's really easy. There's only two wires to hook up. So it shouldn't take you hardly any time at all. So once you get the light in your hands right away, you can tell that it's going to be well-built. The housing is really thick and solid plastic.
So we shouldn't have to worry about getting brittle and breaking over time. Flip it around to the back inside there's going to be some sealer. So this is going to be submersible. So I do recommend though, if you do plan on putting this completely under water, not a bad idea to turn the power off to the light, just to be on the safe side. We're going to have quite a bit of wire to work with here, about seven and a half inches.So we shouldn't have any issues getting it hooked up. And we're also going to have a sheaving that covers pretty much the whole length of the wires. So little bit of extra protection there, as far as that goes. It does come included with the rubber grommet. So that's nice and I am not saying you have to not worry about picking up separately or you don't have to deal with reusing the old beat up one, so nice little extra you get there.To begin our install, we're going to be here at the corner of our trailer. And the first thing we're going to need to do is install our rubber grommet. So pretty straight forward here, we'll just take the grommet and work it into that opening there.From there, we can grab our light. We're going to run the wires through, push it down into that grommet to get it seated like so, and then we can hook up the wires coming from our light to our existing trailer wiring. So what I'm going to use to do that is these heat shrink butt connectors. These don't come included, but you can find them here at etrailer. Slide the butt connector onto the end of the wire. Cut it down. Going to do that for both of them. So the white wire coming from our trailer light is going to be the ground wire. So I'm going to hook that up to our existing trailer ground and the black wire coming from our trailer light. That's going to get hooked up to power. So here's our existing power wire, slide that in. Perfect down and since these are heat shrinks and I'm going to do is take my heat gun and shrink down the ends.So now it's a good idea to test our light, to make sure it works properly. So we'll put power to it as you can see it illuminates up. So this is what it looks like now that I secured our wiring and I just used a zip tie to get that done. And if you need some of those, you can pick them up right here at etrailer and that'll finish up our look at and our installation of the Optronics trailer Light led clearance and side marker light..
Ratings & Reviews

Greg
10/17/2017
Those lights, and all the lighting and trailer wiring products that I bought from etrailer.com, are working great! I used to have constant problems with the lights on my trailer until I switched everything out to the LED lights from etrailer.com! Now they work every time we use the trailer knock on wood!.

David H.
9/1/2021
Everything I’ve done to my truck with multiple products from Etrailer has just been perfect. All working and performing as expected. Couldn’t have ask for more reliable products than those I’ve installed.

Jerry N.
6/19/2018
Always great, tested products from ETrailer. These LED lights did not disappoint...still shining brightly. Thanks!

Lowell C.
3/12/2016
John, Are these lights clearly visible during the day time? I bought some that look similar but are not bright enough to be seen. Im also using them for turn signals on my RZR.

John C.
3/15/2016
Lowell C. These lights are bright enough to be seen during daylight. I use them when I am with a group to signal our next direction or 4 way as intent to slow. Everyone behind me have been able to see them even in high dust situation.

John A.
4/21/2016
Still loving it. I installed them as turn signals on my 12 RZR. Every time I go out riding they are utilized and many have made comments on how well they look and can be seen.
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.







Mack
5/9/2024
Still working perfectly.