Solera RV Slide-Out Awning - 7'1" Wide - 48" Projection - White

Ask the Experts about this Lippert Components RV Awnings

• Slide Topper for 84-1/2 Inch and 149-1/2 Inch Flange to Flange Measurement
  We have exactly what you need, with the Solera RV Slide-Out Awning and does include the rail, and I'll give you the part numbers based on your measurements. - 84-1/2": Solera RV Slide-Out Awning # LCV000165062 (Black) or # LCV000163287 (White) - 149-1/2": Solera RV Slide-Out Awning # LCV000165061 (Black) or # LCV000163299 (White) In addition, the 3-1/2" you mentioned is plenty for the slide topper for water will not sit on top. For weather tape (butyl tape) you can use the Butyl...
  view full answer...
• Slide Out Awning for 80-3/4 Inch Slide for 2019 Aura Trail Lite 22RF
  Thanks for the photo and you are right about the fit for the 80-3/4 inch slide on your 2019 Aura Trail Lite 22RF; the correct one is the Solera RV Slide-Out Awning # LCV000163287. The exterior framing piece is not something I believe is going to be an issue for the install. The brackets should go inside and under that framing piece, and it doesn't look as if it extrudes outward so that it will interfere, so I don't foresee any issue at all. In regards to the awning rail, you just...
  view full answer...
• Can an RV Slide Topper Fit Under Awning
  It's not uncommon to have a slide topper installed below the awning of the RV if the awning happens to be over the slide out. As long as you have room for a rail to fit under the main awning rail this would be totally fine. To pick out the correct slide topper you need to measure the width of your slideout including the flange that goes around the outside of the slide out. If that dimension is between 80 and 85-3/4 inches the Solera 7.5' Slider (Slide-Topper) # LCV000163287 that you referenced...
  view full answer...
• Slide-Out Awning for a Dutchman Denali with 10 Foot Wide Slide-Out Box
  To order the correct Solera Slider, select the fabric size that extends a minimum of 2-1/2" beyond each side of your slide box width. Box width is measured on the outside front of the box including the flanges. Also keep in mind that you will need 6" of clearance beyond the outside edges of the box to accommodate the overall length of the assembly. If 10 feet is the outside width of the slide-out including the flanges then you would need to look at 10-1/2 foot awnings such as # LCV000163293....
  view full answer...
• Will the Solera Slider (Slide-Topper) Fit a 4.5 Inch Tall Flashing
  The height of the torsion arm will play a part in determining if the 4.5" flashing you have on your RV will work with the Solera 7.5' Slider (Slide-Topper) in White part # LCV000163287. However, this will be very difficult to measure as the position that the awning rail is placed will also play a large factor. I recommend placing the awning rail along the line where the roof and wall meet instead of the minimum 3" above the upper edge as this should give you the necessary clearance you...
  view full answer...
• Dimensions of the Lippert Slide-Topper Mounting Brackets for # LCV000163287
  My contact a Lippert Components confirmed with me that the mounting bracket on the Lippert Solera Slide-Topper Awning, # LCV000163287, measures from the center of the top rivet hole to the bottom of edge 1.050 inches. The bracket will mount as close to the top trim of the slid out on you trailer, so from the bottom of this trim to the bottom of the mounting bracket will be no more than 1 to 1.5 inches. This will be enough clearance for the slider to mount to the slide out between the...
  view full answer...
• Is Solera 7.5' Slider (Slide-Topper) # LCV000163287 a Complete Kit
  The Solera 7.5' Slider (Slide-Topper) # LCV000163287 is a complete set. No other parts are required for installation. I have linked a video review of this series of awnings for you.
  view full answer...
• Recommended Awning For Slide Out With 81 Inch Flange To Flange Measurement
  For your 81 inch flange to flange measurement on your slide out, I recommend the Solera 7.5' Slider (Slide-Topper) in Black w/ Black Hardware # LCV000165062 or the Solera 7.5' Slider (Slide-Topper) in White w/ White Hardware # LCV000163287. The only differences between these is the color of the awning and hardware. They are a confirmed fit for your size slide out. I've attached a video for your reference and you may also be interested in the Camco RV Vent Installation Kit - Rubber...
  view full answer...
• Solera Slide-Out Awning for a 153-1/2 Inch Slide-Out
  For your 153-1/2 inch slide-out you will need a 13-1/2 foot awning. We have white, # LCV000163300, and black, # LCV000168109. Each of these fits a slide-out that is 152 to 157-3/4 inches wide.
  view full answer...
• Adding Slide Topper to Slide Out That Has an Awning - Is there room?
  The access plate is 2-15/16" wide and 7-5/8" long and must be mounted on the slide out's outside wall as far up as it can, but not mounted on the t-molding. The t-molding is what looks like 6" wide trim around the outside slide out wall. I have attached a *.PDF document showing the installation method for Lippert Solera Slide Toppers. Once the access plate is installed the acces bracket slides on by the channels in teh bracket. Note that it can slide on by a high or low position. I...
  view full answer...
• Can I Slide Topper be Used on a Slide Out with an Awning?
  Thanks for the question! When adding a slide topper there are time we can put these on a camper that has an awning already on the slide and times that we can't. In your case there isn't the 4" of room we would need to put it on. The topper requires that brackets be put on the top right and left of the slide below the trim flange that sticks out slightly from the slide. It appears that on your Keystone Cougar 34 TSB that the awning is at the very top edge of that topper (so it can clear...
  view full answer...
• Does the Drip Rail Need To Be Removed To Install a Solera RV Slide-Out Awning
  Yes, the Solera RV Slide-Out Awnings like part # LCV000163287 which fits 80" - 85" wide slide-outs (flange to flange) will require that you remove the drip rail. However, the Solera RV Slide-Out Awning will take the place of the drip rail in regards to function so you should not have any worries here. If you wanted, you could reinstall the drip rail above the awning but this is not really needed.
  view full answer...
• How to Select the Correctly Sized Awning
  There is a way to find an awning for your 2018 Coachmen Clipper 106, though we do not have any specific parts for years, makes and models of trailers. To find the correct awning you need to select the fabric size that will extend at least 2-1/2" beyond each slide of the width of your slide box. For example, the Solera # LCV000251461 is 120" wide and has a box width range of 110" to 115-3/4". I've added a link to our entire selection of awnings for you to check out.
  view full answer...
• Slide Topper for Slide Out that Measures 82-3/4 inches
  Since your slide out awning is 82-3/4 inches in width the correct slide topper you'd need is the part # LCV000163287.
  view full answer...
• How Do the Solera RV Slide-Out Awnings Perform In the Wind
  The Solera RV Slide-Out Awnings will hold up in heavy winds as they have a pre-set tension to reduce billowing and they are made of a much heavier fabric (13.5 oz) which has a five year warranty. Therefore, there should not be too much of a concern with the awning holding up in strong winds. In regards to travel, there is not any sort of cover for the slide topper but again the pre-set tension system is going to prevent wind from getting under the fabric and causing tears. The Solera...
  view full answer...
• Recommended White Slide-Topper for a 7 Foot Long and 13 Foot Long Slide-Out
  Absolutely! For the 7' long slide-out you would want to use the Solera 7.5' Slider (Slide-Topper) in White part # LCV000163287 which fits a box width range of 80" to 85-3/4". For the 13' long slide-out you would want to use the Solera 13.5' Slider (Slide-Topper) in White part # LCV000163300 which fits a box width range of 152" to 157-3/4". The box width range is measured from the outside of each flange on the slide-out. Both of these slide-toppers come with white fabric and hardware....
  view full answer...
• Do Solera Slide-Out Awnings Come with Everything Needed for Installation
  The Solera 7.5' Slider (Slide-Topper) # LCV000163287 does come with everything needed for installation. No other parts are required. I have included a link to a video covering the features of the Solera slide-out awnings.
  view full answer...
• Correct Awning Slide Toppers for 72-1/2", 78-1/2", 84-1/2" and 154-1/2" Flange to Flange Measurement
  Thanks for all that info and I can tell you exactly what awning slide toppers you need for each of the flange to flange measurements you provided. - 72-1/2 Inches: Solera RV Slide-Out Awning # LCV000163279 (White) or # LCV000165063 (Black) - 78-1/2 Inches: Solera RV Slide-Out Awning # LCV000163285 (White) or # LCV000168105 (Black) - 84-1/2 Inches: Solera RV Slide-Out Awning # LCV000163287 (White) or # LCV000165062 (Black) - 154-1/2 Inches: Solera RV Slide-Out Awning # LCV000163300...
  view full answer...
• Slider That Fits 82-1/2" Box Width
  For your 82-1/2" slide out box, the correct awning and hardware will be the Solera 7.5' Slider (Slide-Topper) # LCV000163287 for a white awning and hardware or # LCV000165062 for a black awning and hardware. As for the track, this does come included with the kit.
  view full answer...
• How Much Does the Solera Slide Topper Awning Stick Out On Each Side
  In regards to the Solera Slide Topper Awnings, the overall width is actually adjustable so I don't have an exact figure for you. This is because you can slide the hex extension rod in and out of the support arm bracket. The correct way to choose a Solera Slide Topper Awning is to measure from the outside edge of each flange on your slide out. The support arm will then stick out a minimum of 3" past the outside edge of each flange. I have attached a photo for you which shows this. If...
  view full answer...
• Slide Toppers for 79 Inch 142 Inch and 154 Inch Slide Outs on Grand Design Reflection 303RLS
  If what you measured is the box width of each slide out, including the t-molding, then I recommend the following Solera Slide-Out Awnings: 79 inch box width - # LCV000165062 (black) or # LCV000163287 (white) 142 inch box width - # LCV000177334 (black) or # LCV000163298 (white) 154 inch box width - # LCV000168109 (black) or # LCV000163300 (white) I've attached a photo showing how to measure your box width.
  view full answer...
• How Wide is the Actual Fabric/Canvas on the Solera Slide-Topper Awnings
  The actual width of the fabric/canvas on the Solera Slide-Topper Awnings will be right at the max box width range. The max box width range for the Solera Slide-Topper Awning part # LCV000165062 for black or part # LCV000163287 is 85-3/4" therefore, the actual width of the canvas is going to be around 85".
  view full answer...
• Slide-out Topper Recommendation for 83-1/2" and 153-1/2" Slide-Outs on 2018 Forest River Cedar Creek
  If by outer flange you're referring to the slide-out on your 2018 Forest River Cedar Creek 5th Wheel, you are correct. For the 83-1/2" slide-out you will need the Solera RV Slide-Out Awning # LCV000163287 (white) or # LCV000165062 (black). For your 153-1/2" slide-out you will use the Solera RV Slide-Out Awning # LCV000163300 (white) or # LCV000168109 (black). These awnings will extend 48" and provide your slide-outs with protection from water and other debris that might affect proper...
  view full answer...
• Recommended Slide-Toppers for 85 Inch, 83-1/2 Inch and 85-3/4 inch Wide Slide-Outs
  For your 5th-Wheel Trailer, I recommend using the Solera 7.5 Foot Slider (Slide-Topper) in Black with Black Hardware # LCV000165062 or White with White Hardware # LCV000163287. This slider is 90 inches wide and has a box width range of 80 inches to 85-3/4 inches. The box width is measured on the outside front of box, including flange. Awnings for slide-outs need to extend 2-1/2 inches beyond each side of the slide-out so that they are several inches longer than the slide-out they fit....
  view full answer...
• What is Included with Solera Slider (Slide-Topper) Awnings
  Solera 13' Slider (Slide-Topper) in White w/ White Hardware Item # LCV000163299 includes the awning itself, mounting hardware and brackets, and the awning rail. The same goes for # LCV000163287. Camco RV Vent Installation Kit - Rubber Roofs or Sidewalls - White Butyl Tape Item # CAM25013 is not included.
  view full answer...
• Slide-Out Awnings (Slide-Toppers) for 84, 90, and 156 Inch Wide Slide-Outs
  The 84 inch slide-out will use a 90 inch awning slider length, 90 inches will use a 96 inch length, and 156 will use the 162 inch length. So for the 84 inch slide-out you can use # LCV000165062 for black or # LCV000163287 for white. For the 90 inch slides you can use # LCV000168106 for black or # LCV000163288 for white. And for the 156 inch slide you can use # LCV000168109 for black or # LCV000163300 for white.
  view full answer...
• Correct Slide Topper Awning for a 2018 Winnebago Minnie Plus Travel Trailer
  In order to choose the correct slide out awning you'll need to measure the distance between the flanges on your slide-out (outside to outside). If this measurement is 82-1/4" then you'll need the Solera RV Slide-Out Awning part # LCV000165062 for black or part # LCV000163287 for white. The extra length is already factored into the measurements listed on the product page.
  view full answer...
• Recommended Slide Topper For 81 Inch Slide Out And Electric Awning Upgrade Kit
  For your 81 inch flange to flange slide out, the Solera 7.5' Slider (Slide-Topper) in White w/ White Hardware, # LCV000163287 or the # LCV000165062 in black with black hardware are the correct size for your 5th Wheel. This will fit slide out boxes with flange included from 80 to 85-3/4 inches. It also fits the required minimum of 2-1/2 inches extra on either side of the slider with its 90 inches of fabric. We do have electric awning upgrade kits. I recommend the Solera Manual Crank...
  view full answer...
• Correct Slide-Topper for 77 Wide Slide-Out Box
  If just your slide-out measures 77" then you need a 7-1/2' Slide-Topper. We have this available both in Black # LCV000165062 and White # LCV000163287. These fit box widths (including the 5" flange) of 80" - 85-3/4" so if the 77" is just your box then you would need to add 5" to the measurement which bumps you up to 82" and the 7-1/2' Slide-Topper. If the 77" you mentioned does include the flanges then you will need the 7' Slide-Topper part # LCV000168105 for Black or part # LCV000163285...
  view full answer...

Do you have a question about this RV Awning?