Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Replaces a lost or broken operator and knob on your Ventline Ventadome RV roof vent for motor homes and enclosed trailers. Properly sized mounting screw is included.
Features:
Specs:
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Today on enclosed trailer we'll be installing the Ventline replacement operator with knob and screw for Ventline Ventadome trailer roof vent with metal dome. Part number BV0115-04. We'll also be installing the replacement dome assembly for the Ventline Ventadome trailer roof vent. Part number Bv0534-00. Now you'll need to first take apart the interior portion of the vent. There's four screws that hold the outer trim piece on.
You want to be extra careful here, as the plastic becomes very brittle as it gets older. Next there's two screws, one on the front and back, that hold the screen in place. These are small Phillips head screws. With that done, we'll go ahead and set the screen down out of the way. Next, you'll remove the two screws that hold the operator arm in place. You'll then slide the operator arm out through the slot.
We'll then take the new operator arm, slide it back up into place, and put the two screws back in, holding it to the frame of the vent. Next, we're going to need to go up on the roof of the trailer. Now we're ready to install the new cover. Just slide it in from one side and as you're doing that you want to make sure that the actuator arm slides through the round portion and then up into the channel. Now, it makes it a little easier if you have someone down in the trailer to help guide this through, or to raise and lower the actuator arm if need be. Now, we'll go ahead and lower the lid all the way down where we can bend the tab over. You want to make sure that both sides are bent far enough that there's no chance they can slide back out of the track.
Next, we'll need to go down into the trailer where we'll be attaching the friction clip to the operator arm. That way it can't come off of the new lid. You want to make sure that the concave side of the clip bears against the dome bar. If you've attached the handle temporarily, you will need to unscrew it so we can put the screen back up into place. Once the screen's back up into place you can go ahead and put the handle back on. Finally, we'll put the trim ring of the piece of plastic that goes around the outer edge with the four screws.
With that, that's all there is to it, to replacing the Ventline replacement operator with knob and screw for the Ventline Ventadome trailer roof vent with metal dome. Part number BV0115-04. .
Well made, function better than most plastic clip on.
The two replacement "Operater with Knob and Screw for Ventline Ventadome Trailer Roof" vents are very good and exact replacement parts. I installed them this afternoon and now the vents open and close quite smoothly. Thanks for replacement parts. Without replacement parts, replacing a whole vent with recessed lights on a TrailManor RV would have been an expensive proposition. I would suggest enclosing some instructions. That would have been helpful. Thanks!!
Appears to be the correct operator, but package was missing friction clip and screw, so make sure you don’t throw those out from your old one. They were not loose in the sealed mailer so they obviously got lost or robbed out of the package prior to shipping. Would have been 5 stars if not missing parts.
Nearly exact replacement for original operator that broke during a windstorm. It's worked for a year now, full time, no problems.
This functions well and ultimately was a great replacement, but it is wider than the original part where it goes through the mounting bracket. Soon had to file the bracket to allow this part fit through. So 4 out of 5 stars.
Fit like original equipment. Fast ship ping.
This was an adequate replacement. I did have to do some creative filing to make lever that raises vent hood fit the slot so that it will slide and raise. Picture shows the difference in the old and new part. My Dremel tool ground it to the right clearance in short order. Now works perfectly!
The item that I ordered and received was an exact replacement Installed and works great.
Great customer service and fast shipping
Had a little difficulty forcing the disk through the narrow channel above the mechanism where it attaches to the vent. My vent is old, and has the plastic dome, so I probably should have asked if etrailer had an exact match for that. However, once I got it through the channel, it worked fine. As per my photo, I did keep the old style crank versus the knob supplied. Just my preference. Pleased that works.
Worked great. Easy Replacement.
Best customer service and knowledgeable help of any company I have worked with.
Joshua did a great job of finding the right produce for my old RV. Order was picked fast and delivery on time. I will use etrailer in future for my camper and trailers needs. Thanks again!
Hi folks:
I like ordering stuff from etrailer because the staff is very courteous, helpful and professional. Tamara and George J responded right away to my order and that's a great feeling. The part I ordered was almost an exact fit, the round part on the very end was a little wider than the original one but I just wiggled it through the slot in the vent and everything was fine. The grease they use on the gearing was pretty stiff so I lubed it up with spray lithium grease and it worked very smooth after that and I also used it on the vent track.
All in all the process went very smooth and I will use etrailer again for other purchases !!
Been happy with everything
Mitch G. 
10/31/2024
Working great
Another GREAT product! Installed without a hitch. After installing the replacement operator I realized that the plastic vent dome cover had cracks in it from years of weather and had a minor leak problem. I searched the internet and again, eTrailer.com was the lowest in price. Ordered the replacement from eTrailer.com. Due here tomorrow.... FAST delivery too.
Ed S.
1/24/2018
Working perfectly....... Well pleased with the product!
This is operator is a perfect replacement for my Ventline fan, model V2119, with electric lift. Remove the knob, then the lift motor gear matches the gears on the operator perfectly. I used this on my 1999 Airstream Excella. No modifications are required.
A W.
12/11/2016
Still working perfectly after one year!
Service was excellent and works great. I did have to file a notch in the slide to accommodate for a longer stub on the back side of the part. All the new replacement parts had a longer stub on the back when the original stub was flush with the back of the arm where the wheel is pressed in.
Thom V.
8/13/2020
Great
This product fits my vent perfectly. My old unit had a crank but I’m much happier with the knob. There wasn’t a video for this product but it wasn’t rocket science to figure out how to change it. The time that I placed the order to receipt was fast, and I received an email that it was on the way with tracking information. I’m very impressed with this company. I will use them again!
Claudia
10/11/2019
Great. Holding up with use and still easy to manipulate. Great product at a great price
An easy replacement for my old lift arm, however I did need to drill a new screw hole in the support bar as this one didn't line up exactly over my old mounting holes, not a big deal, five seconds with a drill and it was done.
Mike
11/23/2018
Still working one year later.
Product was just right and installed easily and that's coming from a 68 yr. old female! Quick shipping. One tiny little glitch - the screw provided to attach the knob to the mechanism didn't seem to fit. I used the old screw from previous mechanism and everything was perfect. Thank you for great service, follow up and a good product.
Marlou
5/27/2016
Just fine, thanks!
I’ve never been disappointed with etrai ler
The Vent crank [operator] and the fan blade fit a 1999 Tropi-Cal 6370 perfectly. I also bought four replacement Lexan Vent lids and they fit perfectly as well.
There were four roof vents and three needed new cranks as an August 2017 near miss hurricane either broke the arms or stripped the first two gear teeth that hold the lid down. The polypropylene old lids did not crack or leak, but I thought it time to get new Lexan lids as the shower stall lid and the Fantastic Fan over the kitchen area were both Lexan originally and are in perfect shape STILL. Takes some doing to figure out which parts fit because there are no part numbers on the old parts !
Based upon my arm looking like this one, I ordered it. The mounting holes however do not match. Mine were 2 3/4” this body is shorter. The diagram fails to show the distance between mounting holes. After searching other sites, I find that they display the distance between screw holes, including width / height, This would have saved me time, and money. After fabricating a mounting plate, I installed it. (If I knew I had to get the measurements I would have)
Do you have a question about this Accessories and Part?
Condition: Like New
Notes: May have damaged packaging or minor cosmetic blemishes.
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Matt H.
5/26/2016
Still working great. Thanks !!