Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
This item does not fit your vehicle
2009 Ford Edge
These items fit your vehicle
2009 Ford Edge
To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
This Curt 1-1/4" receiver turns your vehicle into a light-duty hauler with a 2,000-lb gross trailer weight and 200-lb tongue weight capacity. It’s great for pulling small trailers, hauling lightweight gear, or mounting hitch accessories. The Class I rating makes it a solid match for bike racks, cargo carriers, or utility towing setups without being overkill for daily use.
The hitch is made from fully welded, square-tube steel for dependable strength on the road. A gloss black powder coat is applied over a protective base layer to guard against rust and corrosion. The result is a clean look that stays sharp through rain, dirt, and everyday wear.
Each hitch is custom fit for precise alignment with the vehicle’s existing mounting points, so no drilling or welding is required. It uses the factory hardware already in place for a straightforward bolt-on install. The concealed cross tube sits tight under the bumper for a tidy appearance that doesn’t stick out or draw attention.
Once installed, the 1-1/4" receiver opening is ready for a drawbar, pin and clip (sold separately), or your favorite Class I bike rack or cargo solution. Whether you’re loading up bikes for the weekend or towing a small trailer to the lake, this setup gives you reliable utility in a compact package.
Customer Satisfaction Score:
97% were satisfied with this product
3% of customers were not satisfied
Ratings & Reviews
Beautifully finished product. I expect longivity to be longer than most
Easy to install
I wish this hitch came in a 2-1/2 in not the 1-1/4
The CURT trailer hitch video is Not true!
The rear bumper facia can NOT be removed by just removing the the lower fasteners !
The facia is LOCKED, solid.
And impossible to remove without damaging the appearance of my 2023 Camaro RS !!
*Body Facia can’t be removed as demonstrated in the dishonest video !
The demo Curt Trailer video is a lie !!!!!
Great fit. Installation instructions and support was very thorough and easy. Highly recommend this product.We towed across country and had zero issues.
I’ve been using this hitch on my camaro for a while now, although the sound of the ball hitch moving around in the hitch makes you worried it was messing up but it’s normal and besides I haul a trailer with a 14 raptor 700 on it it pulls perfectly before you wonder no I’m not a redneck but in my situation I don’t got a truck and don’t have room for one so this worked amazing overall very sturdy but it has rusted in one spot that’s all the cons I can really say the rust in one spot and the ball hitch I ordered from them it makes a lot of noise in the hitch anyways this is a really good product to buy.
I think I will buy another one, or two... how many to get a deeper discount? We Modify these hitches to be used as a frame mounted tow hook for the Camaro ZL1 & SS1LE cars. This modification also increases the tongue load and towing capacity by locating the receiver directly to the steel crossbar.
Mike L.
4/2/2026
If you're anticipating making multiple purchases, you can apply for a dealer account which would give additional discounts. You can sign up by reaching out to our Customer Service folks at 800.298.8924.
Easy and worked as described
Installation was a breeze. I only had to notch the lower section of the bumper. No complaints at all.
Nice hitch looks good packed well shipping was fast would recommend
Do you have a question about this Trailer Hitch?
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Brooke M.
9/18/2024
Hi Stephen! I saw your review here and wanted to reach out to Curt on your behalf. They say that your model is compatible and that you mustve missed a few of the torx fasteners and screws needed to remove the facia. You will have to remove the taillights and other interior trim as well, to get to the point where you can remove the facia in step 7. I emailed you the video that Curt emailed me that might be a good visual to help you out on this! I have also heard that for this model there is a metal strip that the bumper clips into. You may just have to give it a little more mustard to get it to unclip. I understand the concern of breaking the clips, but it can be done without breaking them. I am sorry it has given you so much trouble!