10" Tall x 15" long wheel cribs can be used to lift your vehicle for service or display. Replaces cumbersome jackstands. High-density foam with durable protective coating. Fit tires up to 10" wide.
Features:
Specs:
Race Ramps Wheel Cribs are sturdy, solid foam blocks that serve as a tough, but lightweight and rustproof alternative to jackstands. They keep your vehicle safely lifted 10" off the ground for service or display. This allows you to perform routine maintenance such as changing your oil, drive belt, or transmission fluid. Additionally, you can use the cribs for display. To use the wheel cribs, raise your vehicle high enough to slide a crib under each tire, then lower your vehicle. The tires will sit snugly in the precision-molded concave cutouts.
These cribs are made of ultra-strong, solid core, high-density EPS foam that won't crack or bounce. Each crib supports 1,500 lbs - giving you a total weight capacity of 3,000 lbs for lifting a vehicle for service or display. The cribs are lightweight, weighing only 6 pounds per crib, so you can transport and store them with ease.
The cribs are covered with a textured coating and are flat on one side. This keeps them from skidding while your vehicle is lifted. The coating is a hybrid polyurea compound that is resistant to water and other automotive chemicals commonly found around the garage. And although this coating is durable, it will not scratch, mark, or scrape your garage floor or the ground.
A built-in handle on each crib makes maneuvering them easy. The cribs can also hang vertically to free up storage space in your trailer or garage.
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Hello everybody, this is Jeff at etrailer.com. Today we're gonna take a look at these Race Ramps Wheel Cribs for service and display. It is for a quantity of two of them. Now these are a 10 inch tall, 15 inch long wheel crib that can be used to lift your vehicle for service or display. Helps replace those cumbersome jack stands underneath your vehicle. And just to show you what we're talking about, if I pop up an insert there, you can sort of get an idea.
There's one of our neighbors that used it to put their vehicle up on these cribs. Now these are lightweight blocks. They're very easy to use, very easy to transport and store. The weight on 'em is only about five pounds per crib. And if you notice, they have these built-in straps that make it very easy to maneuver and carry the blocks to where you need them.
They are made of an ultra strong, high-density EPS foam construction, ensures durability and stability. It is a solid core foam so it won't bounce or crack. And just to zoom in, wanna to try to show you, you can see the finish on it has a nice textured coating, prevents the cribs from slipping or sliding, and it resists water and automotive fluids, won't scratch, mark, or scrap your floor. And again, it just almost feels like a very hard plastic, but it is an EPS foam. Now these are made in the USA.
This is for quantity of two wheel cribs. Application, again, they're for vehicles with tires up to 10 inches wide and tires that have an overall diameter between 24 inches and 30 inches tall. The weight capacity, which is stamped on the bottom, 1500 pounds max per crib. So for both of 'em, 3000 pounds. And the last thing I wanna do is just give you some dimensions on it.
We'll zoom in again. Basically the length of them, if we put a tape measure on it, gonna be right at 15 inches long. The height, again, the very middle, you can see they have a concave design to 'em. So the very middle, it's gonna be right at 10 inches. Both ends are gonna be about 11 and a quarter inches tall. And then the width on them is gonna be right at 12 inches wide. But again, they're very durable, again lightweight, hold your car up on if you're displaying it or if you wanna work underneath it, you can put it right up on these. But that should do it for the review on these Race Ramp Wheel Cribs for your service and display.
Average Customer Rating: 5.0 out of 5 stars (45 Customer Reviews)
10" Tall x 15" long wheel cribs can be used to lift your vehicle for service or display. Replaces cumbersome jackstands. High-density foam with durable protective coating. Fit tires up to 10" wide.
Very light and very strong!
Great product, and great customer servi ce!
We bought this item for our son in law who uses them in car shows for his 1968 Firebird. He is very happy with them.
Great product and great customer servic e!!!!
Perfect for the job at hand, thank you!
They’re great and safe
The product I received was perfect and was shipped to me very fast I will definitely order from you guys again thanks
I have had these for over a year now. They have done great with all the vehicles that we have used them for, from a dually to a 2wd truck and a SUV. Worth what you pay.
Works great very light weight
Good product, good price, and quick shipping service!
Excellent quality. Price could be a little more friendly but these are amazing for doing work.
Came very quickly, and a reasonable pri ce.
These will be a back saver for me doing body work on the lower panels. Amazing how light they are and can still support 1500lbs.
Great job!! I feel much more safe underneath my car. Plus the Jackstands are all was in the way!!
Do you have a question about this Car Ramp?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.