To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
When you’re traveling long distances with your camper, stability makes all the difference. These frame-mounted tie-downs secure your camper to the most solid part of your truck—the frame—so weight is evenly distributed and the center of gravity stays low. That means less sway in crosswinds, smoother handling, and a ride that feels just as steady as if you weren’t hauling at all.
These tie-downs bolt directly to pre-existing holes in the frame, so there’s little to no drilling required. Because they mount tight to the frame, ground clearance stays high and there’s no need for cutting or modification. The custom-fit design makes installation straightforward and keeps your truck’s structure intact while giving you a clean, factory look.
Once installed, the brackets tuck up close under the truck where they’re barely visible. Pop the arms off when you’re not hauling, and the mounts practically disappear. You keep your truck’s clean lines without any bulky equipment hanging down or catching on obstacles.

Made from durable steel and finished with a high-impact powder coat, these tie-downs hold up against weather, road salt, and rough terrain. The heavy-duty construction resists rust and corrosion so you can count on them season after season without worrying about weakening or wear.
Each tie-down arm features two pin holes so you can adjust how far it extends from the body to clear fenders or sidewalls. That flexibility lets your turnbuckles line up perfectly with your camper’s anchor points for a snug, balanced hold that keeps everything tight and secure mile after mile.


Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Today on our 2007 GMC Sierra Classic Crew Cab, we'll be looking at the TorkLift Custom Frame-Mounted Camper Tie-Downs for the front, part number TLC2211. These will secure your drop in pick up campers so you don't have to worry about them rolling around or tipping out of the bed while you maneuver around corners. It will keep them nice and secure for safe travels down the road. As you can see this arm gives us plenty of maneuverability, up and down while it's inserted. Depending on how true whatever you're trying to secure to your camper, your drop-in camper, you have some play there to adjust as needed. The bolts that will secure the drop-in camper is also slotted so you have more adjustment room there as well. Pretty much, 11" straight to the bottom of it.
At the lowest point of the frame, it's about the same. Realistically our ground clearance really didn't change any at all. Now the arms have two slots, depending on the size of the camper that you have in the back of the pick-up. More than likely you'll probably be using one that's closest to the base on most applications. They're really easy to install. Just slide it in, take the included pin and clip, insert the pin and secure the clip, like so.
Ground clearance, the lowest point is about 9 1/2". From the bottom of the rocker panel here is about 7". Now let's take the arm out to the second position. Ground clearance looks to be about 8". From the same point on the rocker panel we've added about 11" to the vehicle. The first thing we want to do is take one of our 1 1/2" bolts here, one of our thin nylon lock nuts, and we'll thread it on for three of those bolts actually.
We want to run a nylon lock nut about 3/4 of the way down. The instructions say to run it halfway down, but we've already installed this bracket on the driver side of our vehicle and found out that it needs to be more like 3/4 of the way down to actually get installed property. Then we can adjust it from there. We'll thread one here, get it to start, and we'll run it down until it starts to poke out the back. Do the same thing for the other two bolts.
I'll thread them into the other welded nuts on the bracket. You may find it slightly difficult to get these to start because the brackets appear to have been powder coated after the nuts we're welded on. On the front of the rear leaf spring, there's a stud that sticks through here. It's a 11mm, and then there's a 15/16 nut that holds it in place. You may want to soak it down with some penetrating oil first because more than likely it's going to be rusted in place and a little difficult to move. Using our 15/16 wrench and our 12mm wrench, we'll hold the stud in place and we'll start to remove our nut. You'll definitely want to make sure you hold a stud in place. Otherwise, you could risk pulling it all the way out, in which case that would happen, the leaf spring would shoot up into the top of the vehicle. You would have a very difficult time pulling it back into place. Now let's take our bracket, slide it into position, like so. Take a large, included flat washer, slide it over the stud, and install the new large nut. Now we can snug our nut down a little bit, still leaving it slightly loose so we can adjust the final position of our bracket. Now using two 3/4" wrenches, we'll start by backing these bolts out until they contact the frame where the body mount goes to. We'll drive it further out, and it'll center our bracket, making it level. Our bolts backed out all the way making contact with our cab mount on our frame. We can hold the bolt itself in place with one 3/4" wrench, and grab another one and we'll back our nylon lock nuts back to the bracket to lock the bolts into position. Now we can run in this bolt here on the top all the way. With our bracket centered and the lock nuts and bolts secure against the frame, we can finish securely tightening the large nut that goes to the leaf spring. Now with a large nut that secures our brackets to the leaf spring tight. That completes the look at the Torklift Custom Frame-Mounted Camper Tie-Downs for the front, part number TLC 2211 on our 2007 GMC Sierra Classic Crew Cab.
Ratings & Reviews

Ralph
3/27/2026
Installed the Tie Downs while in my driveway. Used three quality drill bits, but the installation was fairly easy and they work great!

Victoria H.
4/12/2025
I'm glad we were able to help turn this experience around for you Dan. We'll be here to help whenever you're ready for your next project.

Straw
8/24/2026
A year later, no issues with tie downs, except normal wear and tear and metal to metal wearrust progression. These tiedowns are designed great and fit function was clearly created by someone who knows not only design but install ! E-trailer is “the” place to buy rv, camper, towing etc products - the install videos are sooooo helpful ! Thx ET !


Lazer S.
9/16/2025
It definitely is safe the way you have them, Paul! In a perfect world, the turn buckles would be perfect vertical, but this an imperfect world and not all campers have the attachment points in the same place. If you take a look at some of the installed pictures on the TorkLift Locking FastGun Turnbuckles # TLS9529-2-LK page, you can see most of them are at an angle. It's perfectly normal. Are you running any suspension enhancement on your Silverado?

Paul
9/27/2026
These tie downs are great, so easy to use. Camper never budged a hair


Bob
11/1/2025
I have not had any issues at all with the tie downs.

Kate F.
8/10/2026
Thanks for the pictures Rich. We will be reaching out =)

Heather A.
4/10/2026
Looks great! What kind of camper do you have?

Lazer S.
10/14/2025
Install looks great, Megan! Especially for it only taking two hours! They were moving. : ) Happy we confirmed what you found as well. Tie downs can be a pain in the rear with all the options out there. Now I do have to ask though, have you guys thought about any kind of suspension enhancement for the rear axle? It's a little hard to tell, but it looks like the back is sagging a bit in your last picture.



Clay
7/31/2026
A year later and I would not do anything different. Absolutely the best system available especially paired with the fast guns. The camper is solid mounted and does not move. Yet can still be off loaded in just a few minutes. Remember good stuff isn’t cheap and cheap stuff isn’t good.


Nick S.
1/12/2026
I love these TorkLift tie downs, and it is great to hear you are liking the quality as well. What kind of truck camper are you going to be running with these?

Kate F.
8/20/2026
We appreciate the kind words Charles! Where did you take the in-bed camper for the first trip?

Gwendolyn Y.
9/18/2025
Install looks great, Dale! Where're you headed off to now?


Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.





Victoria H.
3/21/2025
That's awesome to hear Ralph! It looks like Randall helped you out with this one. I'll let him know you gave him a shout out!