# 1
Draw-Tite Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 8-1/2" Long - 7.5K
Excellent quality, fast shipping. Finding a metric ball for our international application was a bit difficult. We knew etrailer was the place to go for all things "trailer" related. Very happy with the purchase!
Strong and seems to be well made and well finished. One-inch ball mounting hole. I used this for a Curt hitch mounted on a 2014 Forester and pulls a small Harbor Freight trailer. Perfect height and trailer is level. Warning - don't get their hitch pin, it does not have a hole for a cotter pin, only a weak clip that I would not trust.
# 2
etrailer Ball Mount Kit for 2" Hitches - 7,500 lbs
Haven’t used it yet, but looks good. I’m not sure what height offset I need, so this kit gives me several options, plus two ball sizes. Really good value.
I installed the draw tite hitch onto my brand new 2018 Subaru outback. I'm 68 years old, not as strong as I was, but proud to say I did the job all by myself in about 4 hours. Here are some tips you may find useful. Watch the video-it’s pretty good. I had difficulty getting the exhaust system down and worried about getting it up again from the moment I got it down...read on-help will follow. I bought a stepup drill bit which worked great for drilling the hole in the chasis. I clamped the hitch onto a floor jack, then rolled it and raised it into position. Used metal shears to easily cut out the heat shield as per the video. Your inclination will be the screw the fishing tool provided all the way up the carriage bolt. That won’t work; just screw it on to the tip of the bolt. I couln’t get the exhaust hangars in place even after lubricating them with wd-40. I dropped the rubber hangars into undiluted liquid car wash soap which made them much more slippery than the wd-40. After that the rubber hangars slipped into place pretty easily-that’s my best tip. Finding the electric connection plug for the wiring harness was almost as hard as installing the hitch. I was very happy with how the job came out. Good luck.
# 3
Curt Ball Mount for 2" Hitches - 1" Rise, 2-1/4" Drop - 7-5/8" Long - 7,500 lbs
Just your basic ball mount, the product is just like most 2” Hitch ball mounts, the service wasn’t very good though. Ordered on June 15th (product was in stock) took them 6 days to send it out, took another 6 days in shipping and got all the way to my post office two days before leaving on vacation (I needed it for the vacation) and the post office said “box was empty and they notified seller” etrailer sent a new one (got here a week after my vacation) in a damaged box (packaging is horrible, little bit of paper in a box with a 5 lbs ball mount) almost lost this one too. I don’t believe I’ll be using etrailer in the future (had issues before)
Does the job, however there's a lot of play when hitch mount is inserted into the hitch and when towing with an empty trailer. Very loud. Have to buy a silencer that goes around and secures the product.
# 4
Curt Class III Ball Mount with 2" Ball - 2" Drop - 7,500 lbs
The hitch and ball mount are excellent quality. My concerns are twofold. The hitch is so heavy that I had to take it to my mechanic to have it installed. Minor cost and inconvenience, but the hitch for my previous F-150 was just as sturdy, but easy to install myself (albeit with higher ground clearance). My concern about the ball mount is that the factory told me erroneously that it could not be reversed for a drop, so I returned it. This order is for the replacement after I was finally correctly told it could be reversed and how to do that. Ball mount would have been a 3 for that reason, and overall hitch and ball mount quality a 5. So I averaged them.
I have two of these. My first I bought two years ago. I very highly recommend this Curt Class III Ballmount 2" Drop because of its price, durability and quality. I towed various class 3 loads with ease and confidence with this ballmount. It slides into the hitch and does its job without fail. It looks excellent after towing a load. etrailer's price is about as good as it gets and delivery is very speedy.
# 5
Curt Towing Starter Kit for 2" Hitches - 2" Ball - 3/4" Rise, 2" Drop - 7.5K
There were some UPS delivery issues, damaged in shipment. But, etrailer.com jumped right on sending out another shipment after it was apparent that UPS would not complete the delivery. The installation took longer, maybe 1-1/2 hours, because I did not have all my tools ready and I was working on the concrete floor in the dark to outside with a portable shop light. Everything fit well and it looks great. The 2" drop ball mount was the perfect height for my 2019 Toyota Highlander Hybrid. I love the look of the Curt black insert that makes the hitch looks like it belongs on the car, nothing embarrassing at all. Anything negative? Maybe. The flat plate was a little difficult to hook onto with the UHaul safety chains on a 5x8 trailer. That's hardly a negative, though, and I wouldn't have spent more on another brand choice because of this. Happy happy!
Great fit and finish on this kit. So nice to be able to tow things with my Forester now. I thought I had an issue but figured out it was user error pretty quick, but only after I contacted etrailer for help. I heard back within 30 minutes of emailing and by that time I figured out my blunder. They were extremely helpful and responsive and were set on fixing the problem I thought I had. I have used etrailer for several different purchases over the past couple years and every time I have been thrilled with the service and the quality of product.
# 6
MaxxTow Adjustable-Height Ball Mount - 2" Hitch - 7-1/2" Drop, 6-1/4" Rise - 5,000 lb
As advertised and quick delivery, I am an Etrailer fan!
Strong and works perfectly!
# 7
Draw-Tite Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 9" Long - 7.5K
Sara R was helpful helping me find the right hitch for what I described as needing. I was excited to see the hitch pin in my order details even though I didn't order it. Sadly, the picture gave me a false impression. Overall, excellent customer service and product.
Working in the sand and grass of my driveway my wife and I installed our new etrailer receiver hitch. Great fit and finish! Went right on as described in the online guide. Hitch required a spacer washer on top back bolt attachment point. Taped it on so it would not move while lifting in place and it stayed right there! Used a car jack to raise up and hold the hitch into the underside of the trunk tighten the bolts and reattached the tail pipe done. Now we can pull our Sunfish Sailboat any where the car will go.
# 8
Curt Drawbar for 1-1/4" Hitches - 3-1/8" Rise - 9-1/4" Long - 3,500 lbs
great product great service I bought the hitch took me 15 minutes to install it on a 2004 civic fast shipping great company thanks
Good and strong but not a great angle/height for my application so had to go to a straight line fit.
# 9
Draw-Tite Drawbar for 1-1/4" Hitches - 5/8" Rise, 1-1/4" Drop - 7" Long - 3.5K
Items packed well delivered on time. Doesn't get much better that that.
The service is great and so is the price. Box came damaged but if it installs as easy as the last one I bought from etrailer I will be very happy!
# 10
Curt Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs
Longer stinger let me drop the tailgate on my Tacoma with trailer attached. Replaced a similar but shorter Curt hitch and both are very substantial and well made for the weight of my trailer.
With good information from the website it was easy to order a Curt 2" Trailer Hitch, the Upgraded Circuit Protected Tail Light Converter Hardwire Kit w/ 4-Pole Connector and Circuit Tester - 119178KIT, Curt Ball Mount for 2" Hitches (3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs - D-4), Curt Pin and Clip Hitch Receiver - C21500, Rubber Tube Cover for 2" Trailer Hitch Receivers - I-728,Review, and 2" hitch ball 40038. Parts were delivered earlier than the initial estimate. Self installation (on a sloped drive way) took just under 2 hour. The fit of parts was very good, instructions and on-line video's were very helpful. My Kia did not have the wire plug in option, but the splice connections in the wire kit were easy to install. Most of the parts are hidden from view when the ball mount is not used.
# 11
Brophy Drawbar for 1-1/4" Hitches - 5-1/2" Rise, 6" Drop - 7-1/4" Long - 3.5K
I just purchased a new hideaway hitch system. But the hitch sits only 15 inches off the ground at best. And, my trailer coupling is 22-23 inches off ground. So l needed 7-8 inches of rise on the new 1.25 inch receiver system. Internet research took me to etrailer and the Brophy hitch. I got 5.5 inches with the Brophy hitch, the highest available for a 1.25 inch receiver I could find. The others are limited to 5 inches max. I added another 1.5 inches with your Curt shock absorbing hitch. Voila, with a combined 7 inches of rise and on level ground the trailer now rides perfectly level!!!! Both parts were very easy to connect. Delivery was speedy. Thank you for saving the day and my investment in an expensive new hideaway hitch!
Quality parts, but the extra rise with this and the Curt Rocker Ball still wasn’t enough to avoid scraping the top of my inclined road while towing my boat.
# 12
Curt Tri-Ball Mount - 3 Chrome Balls - 10,000 lbs
definitely solid as a rock
Excellent product! With the three different ball sizes, this tri-ball mount gives you a lot of flexibility. Gone are the days of having several different ball mounts to fit different tongues. High quality construction makes this an excellent investment.
# 13
Curt Class II Drawbar - 5" Rise - 9-5/8" Long - 3,500 lbs
I am an infrequent trailer user, but getting my daughter home from college was necessary in March. This drawbar fits my hitch and utility trailer well, did exactly what it is supposed to do, and was the last thing to be concerned about right then. I have a '11 Mini Countryman S with a Class II receiver from Mini Fini, (which cost twice as much as a Curt) where the hole is flush with the fake grille near the bottom of the bumper cover, so I needed the long bar to reach out past the bumper. The Curt receiver for that car hangs visible underneath the bumper (ugly), which also increases the lever arm on the receiver beam and would have needed an even taller rise. (Curt take note!) All just part of the kit to create an occasional 1 ton pickup out of my Mini, leaving the "bed" at home most of the time.
Fits perfectly. I just wish you would’ve sent a pin with it because I had to go chase that down and get an aftermarket one at Ace Hardware.
# 14
Pro Series Tri-Ball Mount for 2" Hitches - 1-7/8", 2", 2-5/16" Balls - Black
EVERTHING WAS EXCELLENT FROM PLACING THE ORDER TO RECEIVING THE PACKAGE AS WELL AS THE FOLLOW UP. WOULD STRONGLY RECOMMEND ETRAILER....
Not only did I get the parts I needed at a great price. They were delivered they day after I ordered them. Great communication from my salesman. I will definitely be a return customer.
# 15
Convert-A-Ball Ball Mount for 2" Hitches - 10-3/4" Rise, 12" Drop - 7,000 lbs
Not that many non-adjustable option for a 12” drop and this one is the best! Love the cushion and it’s very strong. I put that to the test today when I got rear ended with it in the back of my truck. This thing saved the back of my Ram. Came right back to etrailer and ordered a new one!
This mount was used to bring a Buick up to 19 inches to tow a M/C trailer. The rubber insert cushions starts and stops, and the mount worked as it should to trailer one or two motorcycles easily. Recommend this company and this rubberized insert mount!
# 16
Curt Multipurpose Ball Mount with 2" Receiver for Bike Racks and Cargo Carriers - 7,500 lbs
I am using the hitch for a car dolly and a bike rack. The fit is a little loose for the bike rackmI'll see it really works when get on the road.
Quality is excellent. However, it did not work so I am not sure what to do with it. I thought I could use the top hitch for a Bike rack and pull a utility trailer with other toys. The trailer is too close to make a turn so good try but not able to use it. Thank you for asking. I did not open the box for a while because I was having the trailer worked on so assumed I waited too long to return.
# 17
Curt Multi-Ball Mount for 2" Hitches - Solid, Black Powder Coated Shank - Black Balls
Weights a ton. Seems very strong...10,000 pounds using the 2 5/16s balls. Good paint.
Functionally, this hitch has been great with no issues to date. Aesthetically, the black color did quickly fade to a gray color within a couple of months. Ball surface also presented rust after very minimal use. That being said, I did buy a hitch to tow trailers, not look pretty.
# 18
Curt Class III Ball Mount with 1-7/8" Ball - 2" Drop - 3,500 lbs
Very pleased with etrailer. Very easy to order from website. Fast delivery, easy to install ,perfect fit . Thanks. .
Works perfectly. Fast shipping. Very Satisfied.
# 19
Draw-Tite Ball Mount - 6-3/4" Rise, 8" Drop - 10" Long - 5,000 lbs
Just as advertised and solves my problem of trailer tongue level to hitch position. Delivered on schedule with no hiccups. Fits perfectly in the 2" factory receiver on my Jeep JKU. The 2" ball in the picture is a reused one not new which is why it has rust on it.
I placed my order at 11:24 am Monday. At 1:07 pm, I was informed that it had shipped. Furthermore, though I requested Standard shipping, George went ahead and sent it Express. I got my ball mount today, three days after I ordered it. Now if that's not the way business should be done, then what is? I'm all about getting the job accomplished, sooner the better, and etrailer.com is my kind of company! I have bookmarked their site, and I won't hesitate to shop with them again. BTW, the ball mount does exactly what I needed done, my boat trailer is nice and level now, not pointed at the sky like before!
# 20
Draw-Tite Drawbar for 1-1/4" Hitches - 4" Rise - 10" Long - 2,000 lbs
works well brings the trailer tongue up to level. I have it on an EV so the raddle is annoying, because I just keep on forgetting to buy a anti rattler.
This is very sturdy hitch. It is made of solid steel, not tubing. It will be used on my Mazda RX-3 to tow my car dolly to the RV lot where I will swap everything around and the car will end up on the dolly behind my RV.
What our customers are saying:
"I like the easy of navigation through the site. It only took me a couple of minutes to place my order. Thank You I will shop this sight again in the future."