# 1
Curt Multi-Ball Adjustable Ball Mount for 2" Trailer Hitches
Coming in at about 45 pounds, the D900 Curt Multi-Ball Adjustable Ball Mount is a BEAST! I purchased for use with my '08 Expedition towing either a small utility trailer w/ 1 7/8" ball or my DooLittle Bullitt cargo trailer w/ 2" ball. I needed 5 inches of drop (at least) for both. This is just about the only economical mount in which to accomplish this. Most if not all two ball mounts are 2" and 2 5/16" balls. Many reviews comment on the length that this mount sticks out and initially that was a concern of mine. Please see the Q&A of the D900 product page to address those issues. Short story: A hollow/tubular extension shank of (about or greater)15" reduces vehicle hitch capacity by 50%. The D900 shank and other components are SOLID steel. No reduced capacity. Specifically in my case; this extra length will allow me some personal maneuvering room when hooked up to the DooLittle and raising the lift gate of my Expedition. Clearance between raised lift gate and cargo trailer was about two inches using my old shank, and I should about double that. The anti-rattle tightening bolt is a nice touch. This is my first Etrailer purchase, but not my last.
VERY sturdy piece of hardware here. I was worried it might be a little flimsy piece of metal. Not so, this is a substantial hunk of engineering and I feel safe putting anything on the back of my Expedition! Fully adjustable and easy to install, just like it says!
# 2
etrailer Ball Mount Kit for 2" Hitches - 7,500 lbs
I'll start off with the great customer service, called a rep for assistance and did a great job. He walked me through everything for about 5 minutes. Then I proceeded to order parts at a very reasonable price. Shipping was right on time and tracking was top notch. Now for the parts I received. Trailer hitch receiver was built like a tank, and very easy to install. I didn't even have to take off the whole bumper which I see on your website. There is only one problem with this hitch receiver. Zip ties to hold the facia bracket? It's like putting a $10 paint job on a Rolls Royce. I'm sure you have a good R&D department, but this is unacceptable. I could tell you how to make this better but I'm not part of your team. Could be solved by putting a ___ on the ______. R&D should be smart enough and paid well to figure this out. No offense but they can do better. ??ZIP TIES?? Also, it is pitched with a cap but did not receive that. I also purchased A brake controller P3 and a ball hitch. The ball hitch is pictured wrong on your website. It's pictured with an adjustable ball hitch. This is what really wanted but got something entirely different. If it works, I'll be fine with it. I should have caught that, but my eyes adjusted on the adjustable ball hitch. P3 brake controller was very easy to install, about 5 minutes. On a closing note, I will order from etrailer again. Thanks for your business. Just please listen to your customers and fix these problems. Everything and everybody are not perfect. Thanks again.
The hitch assembly included everything needed for quick and complete installation. Perfect fit for my 2023 Honda Passport. Have been using etrailer for some years now and have never had a bad experience. The self-help videos are a plus for customer service. Good work guys!
# 3
Draw-Tite Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 9" Long - 7.5K
To be honest, I use it upside down. I needed a hitch with rise, but none were available at time of purchase, and yours, inverted, works perfectly! The welds are regularly checked and remain all secure. It's a good hitch.
Working in the sand and grass of my driveway my wife and I installed our new etrailer receiver hitch. Great fit and finish! Went right on as described in the online guide. Hitch required a spacer washer on top back bolt attachment point. Taped it on so it would not move while lifting in place and it stayed right there! Used a car jack to raise up and hold the hitch into the underside of the trunk tighten the bolts and reattached the tail pipe done. Now we can pull our Sunfish Sailboat any where the car will go.
# 4
Rapid Hitch Adjustable, Aluminum Ball Mount Kit w/ 2 Zinc Balls - 5-1/2" Drop
The hitch was received quite quickly and is even nicer than the picture shows it to be. I pull different trailers and it was always a hassle to have the correct hitch. I also like that they did a follow up call when I requested the item be shipped to an address other than my billing address. We are all concerned about credit card fraud. I will definitely order from them again!
I've used the hitch over the last year on several trailers and loads. The adjustability made towing a much better feel and ride over a fixed hitch that at times not the greatest. I see no wear, very easy to adjust even once coupled to the trailer and finding the trailer needs to be leveled better.
# 5
Draw-Tite Ball Mount for 2" Hitches - 1" Rise, 2" Drop - 8-1/2" Long - 16K
A small shipping glitch , but they took care of it quickly
I had a great experience ordering from you. Your organization kept me completely up to date with the order & shipping process and delivered the exact products I ordered. Attached is a photo of the 16,000 lbs capacity hitch and 30,000 lbs 2 5/16 ball you sold me in use. The boat and trailer total about 12,000 pounds. Thanks again.
# 6
Draw-Tite Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 8-1/2" Long - 7.5K
Great Product
Strong and seems to be well made and well finished. One-inch ball mounting hole. I used this for a Curt hitch mounted on a 2014 Forester and pulls a small Harbor Freight trailer. Perfect height and trailer is level. Warning - don't get their hitch pin, it does not have a hole for a cotter pin, only a weak clip that I would not trust.
# 7
Curt Multipurpose Ball Mount with 2" Receiver for Bike Racks and Cargo Carriers - 7,500 lbs
This worked very well for our needs, allowing us to attach a 4-bike carrier and a cargo trailer to our Expedition.
We sold our small motor home and purchased a small travel trailer. This hitch provided a perfect solution to how to use our bike rack while towing the trailer. It even allows room for the pickup tailgate to be lowered without removing the bikes from the rack. The hitch is very hefty with a high weight limit - plenty for the GVW of the trailer (7,000#) plus 125# of rack and bikes.
# 8
Hidden Hitch Ball Mount - 3/4" Rise, 2" Drop - 15-3/4" Long - 6,000 lbs
Very happy with this ball mount - provides just the amount of drop we required for a level tow of our GeoPro travel trailer by our RAM2500. Plus, the extra length not only allows a tighter turning radius, but also allows us to lower the truck tailgate without having to detach the trailer. Huge improvement on all accounts for us compared to our prior setup. The product is well built and I'm confident will provide us years of good use.
Great customer service. Live in SC - ordered a hitch and USPS delivered it to PUERTO RICO. Go figure. Stacey A refunded my money - but 2 weeks later hitch appeared on my doorstep. All’s well that ends well.
# 9
Curt Heavy Duty Forged Ball Mount with 2-5/16" Ball - 2" Drop - 15,000 lbs
Everything, when I need something for my truck I always turn to etrailer. They make it so easy to get the product you are looking for. The quality of their product and the Customer service are the BEST! Thank you.
Great solid forged Ball mount!
# 10
Curt Ball Mount w/ Sway Control Tab for 2" Hitches - 3/4" Rise, 2" Drop - 7,500 lbs
I cannot use this ball mount because the shaft is too short that goes into hitch receiver on my one ton Dodge truck. It does not allow enough room between truck back bumper and ball to allow any trailer tongue to be put on ball.
I purchased this for use with a friction anti sway device I installed on an enclosed V nose trailer. It worked well.
# 11
Rapid Hitch Adjustable Aluminum Ball Mount Kit - 2 Zinc Balls - 5-1/2" Drop, 6-1/2" Rise
Impressive quality!
I have a 4” drop on the rear of my truck, so this rise was perfect to keep my little trailer at the correct height. Great looking product.
# 12
Gen-Y Torsion 2-Ball Mount w/ Stacked Receivers - 2" Hitch - 7-1/2" Drop/Rise - 10,000 lbs
Pulling a cargo trailer with a f450.Pulled very smooth,
I did my research before ordering. I know exactly what I need and want. My boat trailer tongue weight is 750lbs so I went with the Gen-Y Torsion Flex 2" Hitch - 7.5" Drop/Rise 10k. (Works Best with 400-1,000lbs tongue weight). Also got the BEST price due to their 110% Price Match Guarantee.
# 13
Curt Ball Mount for 2" Hitches - 1" Rise, 2-1/4" Drop - 7-5/8" Long - 7,500 lbs
Ordering was extremely easy and etrailer representative very helpful. Chedi also sent me videos that explained perfectly how to install. I don't usually leave reviews, but these guys deserve a good one. Customer service and products delivered were impressive.
This is a great all-purpose hitch. I've used it to mount a heavy-duty bike rack and a steel T-rack to carry a canoe as well as lumber. Most recently I hauled 5 x 8 cargo trailers full of plants, then furniture for a 600-mile move. It was simple to use, problem free, very strong and sturdy. Now that I live on some acreage, I see a trailer in my future, so this will get a lot more use. I drive a 2013 Tacoma, so this is a good size hitch at a good price with sufficient capacity for my needs. I do use a key lock for the hitch as well.
# 14
Convert-A-Ball Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10,000 lbs
My usage of your hitch is a bit unusual, I think. I pull a two ton roller with my Ram and I've used your cushioned hitch to smooth out the process. The roller Lunette just dropped over a 2" ball and then banged and jerked on the ball neck. Check out the photos for my adaptation.. I can flip it over and use the 2" ball! Have enclosed some photos. The cushion is holding up very well and it takes a beating!! Thanks
We have a Pink Tractor (google Mom's Pink Tractor) that we pull to events, mainly in Ks, Ok, Mo, and Ne. We have around 35 events a year we take the tractor to to promote breast cancer awareness. The other day my wife and I were leaving for an event, i had let a friend borrow the hitch to see how he liked it. In less then a mile from the house my wife started complaining about the trailer jerking. That is coming from a lady that really was upset when I paid that much for a hitch. She told me to stop and buy one. (a long and expensive trip, we had to stop at a casino so she could rest her neck) I could write a review with a lot of trailer talk, but, this story tells the story.
# 15
Flash Simple 2-Ball Mount w Chrome Balls - 2" Hitch - 6" Drop, 7" Rise
I like the look of this set very much and it is easy to mount and adjust the ball mount. The workmanship and finish are beautiful. Customer service was excellent in assuring I found the correct mount for my Ford Escape. I pull my 6'x10' utility trailer or very seldom my pontoon trailer. I like that the adjustable mount comes off very easily as I remove it until I need it while my vehicle is in the garage--it helps prevent knocking your leg against it in the garage. However, I am not having any luck loosening the bolt that secures the 2 chrome balls to the adjustable ball mount; I have the correct Allen wrench but cannot exert sufficient torque to loosen the bolt while the adjustable ball holder is off the ball mount. I want to put a different ball combination on so I can pull my son's trailer, which has a smaller ball than comes with the set, if I have to. I also added the anti-rattle device and it stops the mount completely.
This still looks good with no slop easy to switch between the different ball.
# 16
Curt Class III Ball Mount with 2" Ball - 2" Drop - 7,500 lbs
The hitch and ball mount are excellent quality. My concerns are twofold. The hitch is so heavy that I had to take it to my mechanic to have it installed. Minor cost and inconvenience, but the hitch for my previous F-150 was just as sturdy, but easy to install myself (albeit with higher ground clearance). My concern about the ball mount is that the factory told me erroneously that it could not be reversed for a drop, so I returned it. This order is for the replacement after I was finally correctly told it could be reversed and how to do that. Ball mount would have been a 3 for that reason, and overall hitch and ball mount quality a 5. So I averaged them.
I have two of these. My first I bought two years ago. I very highly recommend this Curt Class III Ballmount 2" Drop because of its price, durability and quality. I towed various class 3 loads with ease and confidence with this ballmount. It slides into the hitch and does its job without fail. It looks excellent after towing a load. etrailer's price is about as good as it gets and delivery is very speedy.
# 17
Rapid Hitch Adjustable, Aluminum Ball Mount Kit w/ 2 Greaseless Balls - 4" Drop or Rise
Great fit and finish looking forward to the first tow with it.
This is a must have for full-time trailer hauling. No ball grease needed. Easy to adjust for a level trailer, smooth towing. I increased my trailer tires to light duty truck tires (a little taller tire), for heaver loads & ease of mind to haul at 75 mph speed. This hitch allow me to fine tune the trailer ball height for best setup on my heavy duty Toyota Tundra truck.
# 18
Convert-A-Ball Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 10,000 lbs
Love these. This is my third one. Wouldnt pull a trailer with anything else. Trannys are expensive.
As a full-time RVer, e-shopping is very important for us. etrailer was the right place to shop. Right product, delivered on-time for a great price. You beat the local discount RV store by $25 including shipping. At the same time, I had another outfit send me a clearly inferior product to the one they displayed. Said they would e-mail a pre-paid shipping label for the return (didn't) and tried to put the blame on Amazon. Thanks etrailer for a great experience !
# 19
B&W Tow & Stow 3-Ball Mount - 2" Hitch - 7" Drop, 7-1/2" Rise - 10K - Black
Awesome hitch, I use it on a 2003 Ford F-350 and 2005 Ford Expedition, so much nicer just carrying one hitch for any trailer I tow compared to having all different hitches to deal with and lug around
Works as it should. I enjoy not having to hunt for different hitches when switching trailers. So far no rust..
# 20
Curt Heavy Duty Forged Ball Mount for 2" Hitches - 5" Rise - 6" Drop - 17,000 lbs
This is one solid hitch. Bought the hitch to pull about 5000 lbs. there's no doubt in my mind that it can handle it.
Great hitch’s. Very heavy duty and e trailer is wonderful to work with. Ordered wrong size no problem with return replacement sent out the next day. I should’ve read the sizes. Lol
What our customers are saying:
"WOW! I am impressed! I called to place my order and real person answered, spoke perfect English, albeit a slight southern accent, and my order was sent within a day, shipped quickly and I had it a few days later. I saved over a hundred dollars over local and installed it my self. I cant imagine how that they could do any better. THANKS!"