Most Popular Fixed Ball Mount for 2017 Hyundai Tucson

Appears to be heavy duty and well made. Time will tell, but an excellent price.

Great company to work with.

No complaints here works as it's supposed to feel solid

solid receiver

I recently purchased this hitch and related wiring accessories from etrailer for my 05 Hyundai Tucson. Following the included installation instructions I found the hitch easy to install. Total install time including the wiring adapter was approximately 1.5 hours without rushing.

I have two of these. My first I bought two years ago. I very highly recommend this Curt Class III Ballmount 2" Drop because of its price, durability and quality. I towed various class 3 loads with ease and confidence with this ballmount. It slides into the hitch and does its job without fail. It looks excellent after towing a load. etrailer's price is about as good as it gets and delivery is very speedy.

Love this product. Thank you for you support.

great value easy install

Nice and heavy duty. Make sure you order the 1/2" pin when you order this.

We really like the hitch we ordered for our Camry. It was extremely easy to install. Fit perfectly!

Etrailer is great. Good service!

No issues after one year of use. Happy with product

My Mini Cooper is lowered and this unit really helped level out the trailer I am pulling. The product is heavy and solid. I would definitely recommend this item

Heavy duty! I was a little bummed when I found out how much more difficult it was to find a half inch pin for this, but no matter. It is a tad loose inside the hitch, so there's a little rattle, but I doubt it's as noticable as I make it seem. Super classy and a welcome change from the typical draw bar style. Goes great with my Volvo V70 T5. Thanks etrailer.com!

Easy to use and haven't had any trouble towing my small trailer with motorcycle on board. Def recommend.

This part came with the trailer hitch I purchased. It was very easy to transfer the ball from my 2" hitch and voila I am now ready to haul my trailer.

Overly tight on the receiver end bit functions as intended.

I am an infrequent trailer user, but getting my daughter home from college was necessary in March. This drawbar fits my hitch and utility trailer well, did exactly what it is supposed to do, and was the last thing to be concerned about right then. I have a '11 Mini Countryman S with a Class II receiver from Mini Fini, (which cost twice as much as a Curt) where the hole is flush with the fake grille near the bottom of the bumper cover, so I needed the long bar to reach out past the bumper. The Curt receiver for that car hangs visible underneath the bumper (ugly), which also increases the lever arm on the receiver beam and would have needed an even taller rise. (Curt take note!) All just part of the kit to create an occasional 1 ton pickup out of my Mini, leaving the "bed" at home most of the time.

Very pleased with etrailer. Very easy to order from website. Fast delivery, easy to install ,perfect fit . Thanks. .

Perfect fit for 2 inch Draw Tite receiver. good price, fast shipping.

Have a 2011 hyundai tucson limited, hitch was easy to install, just 4 bolts. Fits great, really sturdy and solid. I had a second pair of hands during install but definitely not necessary. Didnt even have to jack up the car or move the exhaust pipe. Definitely recommend cleaning the mounting holes beforehand with a toothbrush or wire brush and some cleaner (i used wd-40, it works just the same) and screwing in the bolts halfway beforehand to test fit before you're balancing a heavy hitch receiver trying to get the threads to catch. No complaints so far, haven't used it to tow yet. 2

A very nice unit. It is all welded and looks to be very sturdy. It includes the pin and clip

To be honest, I use it upside down. I needed a hitch with rise, but none were available at time of purchase, and yours, inverted, works perfectly! The welds are regularly checked and remain all secure. It's a good hitch.

Working in the sand and grass of my driveway my wife and I installed our new etrailer receiver hitch. Great fit and finish! Went right on as described in the online guide. Hitch required a spacer washer on top back bolt attachment point. Taped it on so it would not move while lifting in place and it stayed right there! Used a car jack to raise up and hold the hitch into the underside of the trunk tighten the bolts and reattached the tail pipe done. Now we can pull our Sunfish Sailboat any where the car will go.

The Extra Long Ball Mount proved useful immediately upon receipt. Delivery was prompt, and the updates from etrailer.com helped plan transport of several bicycles, simultaneously with a camper trailer. The extended length facilitated use with a Swagman bicycle rack, also purchased via etrailer.com. The product arrived in excellent condition, with correct capacity rating, and works perfectly, and in conjunction with the bicycle rack. I recommend purchases from etrailer.

Works great solid product.

Very prompt delivery... no issues ??

Right on, no problem.

Solid construction, real heavy duty

I purchased the AMSC10 because I needed a 10" drop hitch to tow my lowboy enclosed trailer with my lifted Toyota Tundra. I tried several other types of hitches with this towing combo and I was always disappointed. Mostly because of the fit/sloppiness of the ball mount into the receiver. This would cause a lot of noise and the feeling of the trailer "bucking" while hitting bumps and such. The other hitches that I tried were those cool aluminum ones, both a fixed one and an adjustable one. Although they were pretty, both left me very disappointed. The shipping for this hitch from Etrailer was fast and efficient. I received emails informing me of my order status throughout the whole process. Upon receiving my AMSC10, I tested it out and found it to be a much nicer fit into the receiver. Once I hooked up to the trailer and began to tow, the difference was extremely noticeable. This hitch is quiet, it doesn't buck, and in fact, comparatively, you wouldn't even know the trailer was behind you unless you looked. I am actually really excited about towing with this hitch. I know it sounds goofy, because it is, but it makes the task so much more pleasurable with the cushion ball mount. I'm already thinking about buying the 8" drop for my normal trailers.

Heavy duty , very good quality.

Good product!!

I purchased this hitch reciever because it is exactly what I needed to fit my two trailers. The quality is excellent and very reasonably priced. It arrived in a timely fashion and am overall satisfied with the product and seller. I will be doing more business in the future.

Quality item.

Perfect for my Tahoe. I have a 2019 Tahoe LS 4x4 with the max tow package. The receiver is mounted higher than than on the truck it replaced. Six inches of drop appears to be just about right for my boat trailer.

Haven't been able to break it yet.

I hooked up the draw bar today for the first time to the trailer that I built and the hitch I installed. The draw bar uses a cotter pin that slides on the bolt rather than going through a hole to mount the bar to the hitch. I have never used a sliding on pin in anything - I've only used those that go through a small hole matching the pin. This includes my farm tractor and other tools. I hope it is secure because it does slide on easily. The bar itself appears nice and strong.

Great product. Fit and finish is excellent. I've mounted the Curt 1 1/4" hitch to my 2007 Mazdaspeed3. Taking the rear bumper off, which only took 30 minutes (maybe a few minutes more than that) made it very easy to attach the Curt hitch to the car. I wanted to compliment the Mazdaspeed3's overall appearance, so, I decided to go with the Curt euro ball mount 11 3/4" . Very pleased with the outcome.

This worked out to be the perfect ball and mount for my purpose- occasionally having to use my car to tow my utility trailer. I got this and the DrawTite receiver hitch for my '99 Monte Carlo and everything went together in less time than the estimated time that had been shown. Very happy with both purchases!