Most Popular Rectangle for 2011 Jayco Jay Flight Travel Trailer

These lights are really good for the price! (I ordered 16) They aren't cheap feeling or flimsy. They feel sturdy, durable and they look quality. The wires are the correct gauge and the light bulb is in a rubber grommet for weather sealing. The light is sealed very well and it takes some effort to remove the lens cover. The lens is thick and the color is true. The reflector is bright. I was genuinely impressed with lights especially for the cost. These will be replacing older side marker and clearance lights on my older 1985 Sunstream motor home. My lights are faded, some broken, mostly leaking and more costly to replace than what they are worth. These MC32RB and the Amber version lights will look great! Slightly different style, same size and better looking and better quality than the originals. Very happy with lights and etrailer. Will be ordering more items. Thanks. G.

I purchased red and amber lights to replace the faded and broken ones on my travel trailer. Camping World wasn't able to help me. Found you all while searching the internet. Great produce. Great price. Better than the originals. The screws that secure the lights to the trailer are protected from the weather (they are under the removable lens. Easy to install. Ended up replacing all eleven lights.

First unit arrived broken and was replaced by etrailer no problems. Many thanks to everyone at etrailer.

My replacement lights came quickly and were quite easy to install.

Bright….! The exact replacement.

they fit, water proof tape needs to be included for the price.

Lights were an easy, direct replacement for the incandescent factory lights that came stock on the trailer. Splicing was necessary but the wiring colors were accurate as this is the same manufacturer as oem. I am hoping the LED style last longer than the original. If not I will switch to another brand.

These are great. They fit into a 2x4 piece of steel C channel very nicely. This makes for a very strong and easy to mount combo that actually holds up when pulling the trailer off road. The stock tail light housing was very thin and would rip off going over uneven terrain, not to mention the oval lights would vibrate out. These lights bolt on and won’t fall out.

Replaced all the clearance/marker lights on my 2007 RV. Nice upgrade to the LED and very easy installation.

All products I have ordered from etrailer recently have been good quality at a fair price. Service is good and orders shipped promptly. There are videos about each product as well as installation videos. Good reliable company

I should have looked at the photos more closely, as the wiring comes directly out of the rear of the light. The wiring on the OEM light I replaced was a bit more flexible for mounting the light on the fronts of the two fenders on my tow dolly. Also, the mounting holes for the hardware were a larger diameter than I expected, so I had to use washers to keep the smallish bolts from pulling through. On the other hand, the LED lights are brighter than the incandescent bulbs in the OEM lights and they will NOT come loose from road vibration as did the cheesy bulbs and bulb mounts in the OEM lights. Overall, a definite step up for use. The only complaint was the extra time deciding how to accomplish the wiring and mounting.

Easy install. Be sure to check base of wires on the light. The severe bend in them can crack the insulation and may cause issues. One of mine had it and had to doctor it up, otherwise 5 stars.

We have upgraded all our trailers to LED. This is the first light we have replaced in 7 years. We use etrailer for all our trailer lighting.

The cover almost fit perfectly. Well built. Held up well to a harsh winter. A surprising find was that it keeps our fifth wheel dust free on the inside as well as the outside. well worth the expense.

Exactly what I was looking for.

Perfect fit for replacement. Quick shipping.

It was an exact replacement. Works great. Thanks

Terrific upgrade in my opinion. The installation was pretty easy for me. The light is slightly smaller than the original and I have the corrugated sheet metal siding I did not experience any led hyper flash with this light. I was slightly concerned about this after seeing videos of people changing to led light bulbs on the tow vehicle. This light was plug and play. 4 stars because the manufacturer did not provide a wiring diagram :( I don’t feel you should guess what wire goes where. The least they could do is tell you what they (the manufacturer) wired for ground. In my case, the white was ground, same as my trailer wiring. However I needed to connect green to black to get my turn signal to work. Your situation may be different. Would I buy it again? At this time, yes. I’m hoping this light outlasts my usage of this travel trailer- which should be for many years.

Very bright light, same connectors as my 2001 Shoreland'r boat trailer, just had to plug them in. Cannot say enough about the staff at etrailer, very helpful.

SPLENDID! Popped the old incandescent Side Marker Lights out on my 2008 Triton 21X2 trailer and installed these Thinline LED Clearance and Side Marker Lights (both the AMBER and RED ones). Just Plug-N-Play and my boat trailer looks AWESOME! Shipping was a snap!

Exact match of mine but replaced, fast shipping

This one was much better, although had to switch wires around.

Just got my lights they look great but l will have to wait till it warms up from -15 to install them

Tail light delivered on time and easy to install . LED’s much brighter and visible than the original incandescent bulb. Nice lights!

Quite easy to install and fit my Coachman Freelander perfectly. The prior ones were not sealed, filled with water, and blew the fuse fuse. Beware of the cheaper version on Amazon as they have the same poor seal problem as the original lights which died after <5 years.

Command Triple LED Tail Light Review They work great once they are installed. I have 2002 Gulf Stream Ultra on a Ford E450 Frame. The problem is the actual installation. Command does not include install instructions. What may needed if converting from incandescent bulb to a LED system is a 12 Volt 50 Watt 6 Ohm resistor. Installing a resistor parallel between the Brake/signal and Common wire will be necessary to overcome the hyper-flasher bulb out detection system. This high power resistor needs to be mounted on a metal surface to help disapate the heat created. In my case, I mounted the resistor to 3/4 metal pipe banding. The resistor was suspended so that is would have great air flow. Furthermore, size of the light should be slightly larger than 14 w x 6 7/8 . In my case the tail light was not big enough to cover the old light screw holes. I made this work by centering the light and using lap sealant as a finishing water proof bead. After a long road trip and many signal turns and brake presses the tail lights do look and work great.

I couldn't find taillights for a 50 year old Shasta travel trailer,so I bought these. The wiring is little different but these will work.

Light arrived within a day or two of order. Perfect match to OEM light currently on trailer. Easy to install. Very satisfied with product and service.

It had no gasket to seal it to the fifth wheel

Very pleased with with my first order with etrailer.

The old trailer lights had gotten wet inside and so many of the LED lights didn’t work. This new item has a thick foam gasket that looks promising and should keep the water out. Time will tell. Perfect fit ,all wires identical, piece of cake to install. As for etrailer, they have always done a great job for me, no complaints.

This taillight assembly was the perfect match for the existing unit for my Adventurer Camper, (30% of the LED's were not working). An easy installation. Etrailer is a great company and will definitely use again.