Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Upgrading from older incandescent lights means getting more brightness without draining your power system. This ONE Series LED combination tail light uses just one diode but still throws out a strong, even light that’s easy to see day or night. At only 0.34 amps for stop and turn signals and 0.094 amps for the tail function at 12.8 volts, it’s far more efficient than traditional bulbs. With no filaments to break or bulbs to swap, this LED design keeps shining long after others burn out—up to 50 times longer.
You don’t need special brackets or extra hardware to get a clean install. This rectangular light measures 8-5/8" long by 3-3/16" tall, and the built-in license plate bracket keeps everything tidy on the driver side. It surface mounts directly to your trailer or RV body, and the 3-wire pigtail setup makes wiring clear and straightforward—white for ground, black for tail, and green for stop/turn. The fit looks factory-made when it’s done right.
Bumpy roads and constant movement can take out traditional bulbs fast, but the surface-mount LED circuit board in this light is built to handle it. The durable SMT construction improves heat distribution and holds together against bumps and vibration. The ABS plastic base stays rigid while the red acrylic lens resists cracking and can be replaced if needed. It’s made to last through years of use without fading or loosening up.
Visibility matters not just for safety but also for compliance. This combination tail light covers four essential functions—stop, tail, turn, and license plate lighting—so your setup stays DOT compliant and meets FMVSS 108 and CMVSS 108 standards. The clear lens section shines light directly onto your plate so it’s always readable at night or at checkpoints, keeping you visible and within regulations wherever you travel.
Customer Satisfaction Score:
98% were satisfied with this product
2% of customers were not satisfied
Ratings & Reviews
Lights were very easy to install. Work perfectly. They are just a little smaller than the old type I replaced. Very satisfied with them. etrailer shipped FAST !
Decent brightness and good brightness separation between the tail lights and the brake/signal light
They were easy to install and work perfectly. They are a big improvement over the original lights.
Products worked as advertised.
It works but now I need passenger side to match.
Replacement for factory OEM - 2018 Rockwood hard side A122: Fits perfectly! It’s basically the same lens and bulbs. And etrailer.com had the best price, too.
Not sure why the factory didn’t use the screw holes in each of the corners (maybe they didn’t have long enough screws?), so I swapped the bulbs and used the original back, since it was easier to align and screw the unit back into place.
Perfect fit
Light was as stated. The only thing I would have liked to see is the foam backing as was on the original light.
was easy install, and testing was ok after install
I purchased these to replace my tail lights on my Rockwood trailer. The units I removed used the regular incandescent bulbs and even though they are only 2 years old they were already acting up. They get corroded in the socket areas even with trying to keep them clean. These fit perfect (exact same fixture) are twice as bright the flash is faster (with the LED fitment) and the obvious choice for replacement/upgrade with very little fuss. These have a separate tag light that is plenty bright to illuminate your license plate area. The pricing was excellent and the shipping was extremely fast. Communications with this company is spot on. If you have a question they get right back to you in short order. They also give great recommendations as well. The tail lights were delivered Friday and I installed them in 20 minutes on Saturday. I have purchased from you guys in the past and will in the future. Thank you...
It was an exact replacement. Works great. Thanks
Good quality, and functions as advertised. Brighter than the original incandescent units they replaced, but not quite as bright as I had hoped for. It took more time than expected to install these lights, but I was pretty cautious about leaks and used butyl tape under the units, and silicone around the outside. I previously updated all of the clearance lights to LED with Bargman conversion units from etrailer. Our trailer is now 100% LED.
Satisfied with the part and service. Installed it on the right side to install a C.G. plate.
Exactly as advertised. Good quality. Packaged nicely. Arrived sooner than expected. Acceptable pricing.
Exact replacement
Easy to find the part on web site but I had the part number. However if I did not there was help available. E trailer is easy to work with and they appreciate the customer and are willing to help.
Purchased as a replacement light. Fit and finish are excellent. Easy installation.
Match for the original failed unit. Easy to install, all 4 mounting screws match the original. Fast delivery of the unit. Excellent customer service.
Thank you! Easy to replace!
Just what I needed, east to install, works perfectly
Easy install.
Works great.
Dennis
4/2/2026
They work well, they work as designed. Easy installation
Lazer S.
4/2/2026
It was an exact match at I have not had any issues
I ordered both the RVSTLB0060 and the RVSTLB0061. My only disappointment with the RVSTLB0061 was the LED module was not attached to the frame like the RVSTLB0060. Luckily, I had two small sheet metal screws I could use to secure the LED to the frame mount.
My installation was on a 2016 Rockwood A212HW. The OEM lights were the Optronics incandescent version. RVSTLB0060/61 are direct replacements except for the odd (offset) drill pattern used during factory assembly (they did not use all the Optronic predrilled holes). OEM mounting screws were reused but I added a bead of glue to the threads to help secure over time. Note the factory uses a good bit of RTV silicon on the top portion of the light frame to help hold in place and fit the slight curve of the body.
Terrific upgrade in my opinion. The installation was pretty easy for me. The light is slightly smaller than the original and I have the corrugated sheet metal siding I did not experience any led hyper flash with this light. I was slightly concerned about this after seeing videos of people changing to led light bulbs on the tow vehicle. This light was plug and play. 4 stars because the manufacturer did not provide a wiring diagram :( I don’t feel you should guess what wire goes where. The least they could do is tell you what they (the manufacturer) wired for ground. In my case, the white was ground, same as my trailer wiring. However I needed to connect green to black to get my turn signal to work. Your situation may be different. Would I buy it again? At this time, yes. I’m hoping this light outlasts my usage of this travel trailer- which should be for many years.
Installation was pretty simple with the help of my father-in-law for the wire connecting part! Light looks great and is good quality!
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time.
Ginger
5/24/2025
Still working great after a year!