See what our Experts say about this etrailer Trailer Hitch Ball Mount

• Can Hopkins Wiring Harness for 2013 Subaru Outback be Stored in Hatch When Not in Use
  You can absolutely store the Hopkins Plug-In Simple Vehicle Wiring Harness # HM11143865 in the hatch of your 2013 Subaru Outback when you aren't using it instead of routing it outside the vehicle. The connector end will be long enough to hang outside your hatch when you need to connect it to your trailer. I have added a link to the instructions and a video install for you to check out as well of the Hopkins Plug-In Simple Vehicle Wiring Harness # HM11143865. If you also need a trailer...
  view full answer...
• Recommended Trailer Hitch Ball Mount Rise for U-Haul Trailer Coupler for 2015 Mazda CX-5
  On your 2015 Mazda CX-5, the measurement you need is from the ground to the inside top of the receiver. If you look at the attached video we that measurement listed at 15-1/2 inches so it is different from the 13 inch you referenced. For your 13 inch measurement you will then need a 5 inch rise. I recommend the B&W Heavy-Duty Ball Mount - 5" Rise, 6" Drop - 10-3/4" Long - 16,000 lbs # BWBMHD30014 or the Curt # C45336 and then you will need the # A-90 hitch ball. The pin and clip #...
  view full answer...
  
• Comparing Draw-Tite Trailer Hitches for 2018 Ford Edge Titanium & Edge Tongue Weight Capacity
  Let's start simple, which is the difference between the Draw-Tite Trailer Hitch # 75234 (square tube) and Draw-Tite Trailer Hitch # 75214 (round tube) that fit your 2018 Ford Edge. The difference is mostly just in the aesthetics, with the square tube hitch having a concealed crosstube, and the round tube hitch having a visible crosstube. The square tube hitch also has a higher overall capacity of 4,500 lbs towing and 675 lbs tongue weight compared to 4,000/600 of the round tube, but since...
  view full answer...
  
• Recommended Towing Package For Towing a Utility Trailer With a 2010 Ford Edge Sport
  I recommend installing the Draw-Tite Trailer Hitch Receiver # 75686 on your 2010 Ford Edge Sport. I feel this one looks better than the etrailer # e98870 you found as the Draw-Tite has a hidden cross tube which will sit behind the rear fascia. The Curt T-Connector Vehicle Wiring Harness # C56329 will give you a 4-way flat connector. This is the most common connector used on small single axle utility trailers. Our Ball Mount Kit # 989892 will provide you with a ball mount having a 2-3/4"...
  view full answer...
• Hitch, Ball Mount and Wiring Harness Options for 2012 Buick Enclave Without Factory Tow Package
  For your 2012 Buick Enclave the Draw-Tite 2-inch Class III hitch # 75528 is a confirmed fit. Install instructions and a complete install video are linked for you. The hitch comes with all needed hardware. You will also need a ball mount, hitch ball and pin/clip. I suggest ball mount # 989892. In terms of the wiring harness options you ask a very good question. The available products, non-powered models # 118450 and # C56027 and the powered converter model # HM11141615, differ in one important...
  view full answer...
• Trailer Hitch Receiver and Vehicle Wiring Harness For a 2024 Buick Enclave For Towing a Trailer
  First you will need the Curt Trailer Hitch Receiver # CU29FR for your 2024 Buick Enclave. This receiver will sit behind the factory removable panel on your rear bumper so you will have a clean appearance. Depending on your trailer you will need either the 4-Way # 118761 or 7-Way # C56393 for the wiring. The 4-way is most commonly used on small utility and boat trailers. For trailers with electric brakes you will need the 7-way along with a Brake Controller # C51180. This controller plugs...
  view full answer...
• Will Aftermarket Trailer Hitch Installation Void Warranty on 2020 Honda Odyssey
  Absolutely not, you are protected under the Magnuson-Moss Warranty Act, which makes it illegal for companies to void your warranty or deny warranty coverage simply because you used an aftermarket product, unless they can prove the aftermarket product caused the problem. With that cleared up, the hitch I recommend for your 2020 Sorento is the etrailer.com Trailer Hitch # e98855 because its installation is pretty simple and straight forward and does not require fascia trimming. I'm not...
  view full answer...
• What Hitch and Wiring Harness is Required to Tow a Light Utility Trailer with My 2021 Ford Bronco?
  For a hitch for your 2021 Ford Bronco, I recommend the Draw-Tite Hitch - 2" # DT37GR. The Curt hitch is compatible with all Bronco models and comes with all mounting hardware required for a bolt-on installation. As far as weight capacity, the hitch has a 675 pound maximum tongue weight and a 4,500 pound gross towing rating. In order to confirm whether your vehicle can accommodate this much weight, I recommend confirming your vehicle's weight capacity with you owner's manual. In addition...
  view full answer...
• How to Determine Correct Ball Mount For Malone EcoLight Sport Trailer
  I can tell you exactly how to determine the ball mount with the correct rise or drop for your 2018 Toyota 4Runner so you can tow the Malone EcoLight Sport Trailer # MAL53FR. Since we know the measurement from the ground to the bottom of the coupler on the EcoLight is 14 inches, the only thing you need to do is measure the distance from the ground to the top of your hitch receiver. If the measurement to the top of your receiver is more than 16 inches, you will need a ball mount with drop;...
  view full answer...
• Which Panel Needs Removal to Install Trailer Hitch on 2019 Mazda CX-5 GT
  The panel that would need removal is located between the bumper and the muffler as shown in the provided photos and install video which shows the installation of the # 76138 hitch. The placement of the trim piece would interfere with the installation of the hitch so it would need to be permanently removed. The trim piece is meant to make a slight improvement to the vehicle's aerodynamics. If you'll be towing with your CX-5, you'll also need a ball mount, trailer ball and a trailer wiring...
  view full answer...
  
• How to Choose Correct Ball Mount for Draw-Tite Hitch on 2017 Tesla Model X
  To choose the correct ball mount you'll first need to measure from the ground to the top inside of the Draw-Tite Receiver # 76143 with it installed on your 2017 Tesla Model X, and then from the ground to the bottom of your trailer coupler with the trailer sitting level on level ground. Since the hitch receiver sits fairly low I'd imagine that your trailer coupler will be higher so you'll need a ball mount with a rise like the 2-3/4" rise ball mount that comes with the etrailer Ball Mount...
  view full answer...
• What Hitch Receiver and 7-Way Wiring do I Need for My 2021 Dodge Durango?
  For a hitch for your 2021 Dodge Durango, I recommend the Curt Hitch Receiver - 2" # C13182. The Curt hitch is compatible with all Durango models and comes with all mounting hardware required for a bolt-on installation. As far as weight capacity, the hitch has a 600 pound maximum tongue weight and a 6,000 pound gross towing rating. In order to confirm whether your vehicle can accommodate this much weight, I recommend confirming your vehicle's weight capacity with you owner's manual. If you...
  view full answer...
• What Hitch and Wiring Harness do You Recommend for My 2021 Jeep Wrangler?
  For a great hitch for your 2021 Jeep Wrangler for towing, I recommend the Draw-Tite - 2" # DT78MR. The Draw-Tite comes with the highest gross towing weight capacity we offer (4,500 pounds). In addition to the weight capacity, the Draw-Tite comes with an e-coat finish in addition to the black powder coat for superior protection against rust and corrosion. In addition to the hitch, I recommend a ball mount like the one included in the etrailer Ball Mount Kit # 989892. As far as wiring, if...
  view full answer...
• Recommended 2" Hitch for 2006 Dodge Dakota
  To add a 2" hitch receiver to your 2006 Dodge Dakota I recommend using the Curt # 13230 because of the durability of Curt hitches when it comes to the powder coating; this ultimately helps protect the hitch from dings and scratches that might lead to corrosion that can otherwise reduce the life of the hitch. This hitch is a Class III hitch that is a custom fit for your Dakota, so no drilling will be required during installation. There are some other parts you may not have to get a complete...
  view full answer...
• What Trailer Hitch and Wiring Harness do You Recommend for My 2021 Subaru Forester?
  For a hitch for your 2021 Subaru Forester, I recommend the Curt Hitch Receiver - 2" # C13409. The Curt hitch is compatible with all Forester models and comes with all mounting hardware required for a bolt-on installation. As far as weight capacity, the hitch has a 525 pound maximum tongue weight and a 3,500 pound gross towing rating. In order to confirm whether your vehicle can accommodate this much weight, I recommend confirming your vehicle's weight capacity with you owner's manual. In...
  view full answer...
• What Hitch and 4-Way Wiring Harness do You Recommend for My 2022 Toyota Sienna?
  For a hitch for your 2022 Toyota Sienna, I recommend the Curt Hitch Receiver - 2" # C22UR. The Curt hitch is compatible with all Sienna models and comes with all mounting hardware required for a bolt-on installation. Also, the Curt hitch includes a superior gloss and powder coat than the competitor Draw-Tite # DT55MR. As far as weight capacity, the hitch has a 350 pound maximum tongue weight and a 3,500 pound gross towing rating. In order to confirm whether your vehicle can accommodate...
  view full answer...
  
• What Hitch and Trailer Wiring do I Need for My 2021 Jeep Cherokee?
  For a hitch for your 2022 Jeep Cherokee, I recommend the Curt Hitch Receiver - 2" # C13395. The Curt hitch is compatible with all Cherokee models and comes with all mounting hardware required for a bolt-on installation. As far as weight capacity, the hitch has a 675 pound maximum tongue weight and a 4,500 pound gross towing rating. In order to confirm whether your vehicle can accommodate this much weight, I recommend confirming your vehicle's weight capacity with you owner's manual. In...
  view full answer...
• What Curt Hitch and Tow Wiring Do You Recommend for My 2021 Kia Sorento?
  For a Curt model that fits your 2021 Kia Sorento EX, I recommend the Curt Hitch Receiver - 2" # C34ER. The Curt hitch is compatible with all Telluride models and comes with all mounting hardware required for a bolt-on installation. As far as weight capacity, the hitch has a 600 pound maximum tongue weight and a 4,000 pound gross towing rating. In order to confirm whether your vehicle can accommodate this much weight, I recommend confirming your vehicle's weight capacity with you owner's...
  view full answer...
• All Parts Needed For 2014 Volkswagen Tiguan to Tow U-Haul Trailer
  We can get your 2014 Volkswagen Tiguan set up with the correct ball mount to tow a U-Haul trailer, and just to be thorough, I'll go ahead and list out the hitch and wiring harness you'll need as well: - etrailer Trailer Hitch Receiver # e98906 - T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # 118675 - etrailer Ball Mount Kit for 2" Hitches # 989892 This is the complete set up for your Tiguan, as the Ball Mount Kit gives you a ball mount that has a 2-3/4" rise - which...
  view full answer...
• What Hitch, Wiring, and Brake Controller do You Recommend for My 2022 Toyota Highlander Limited?
  For a great hitch for your 2022 Toyota Highlander Limited without a factory tow package, I recommend the Curt Hitch Receiver - 2" # C99FR. The Curt hitch is compatible with your Limited model and comes with all mounting hardware required for a bolt-on installation. As far as weight capacity, the hitch has a 500 pound maximum tongue weight and a 5,000 pound gross towing rating. In order to confirm whether your vehicle can accommodate this much weight, I recommend confirming your vehicle's...
  view full answer...
• What Hitch, Wiring Harness, and Ball Mount do You Recommend for My 2021 Hyundai Sante Fe?
  For the best trailer hitch for your 2021 Hyundai Sante Fe, I recommend the Curt Trailer Hitch - 2" # C34ER . The Curt hitch is compatible with all Sante Fe models and comes with all mounting hardware required for a bolt-on installation. As far as weight capacity, the hitch has a 600 pound maximum tongue weight and a 4,000 pound gross towing rating. In order to confirm whether your vehicle can accommodate this much weight, I recommend confirming your vehicle's weight capacity with you owner's...
  view full answer...
• Recommendation for a Ball Mount to Fit a Hitch on a 2014 Ford Edge
  For the Draw-Tite hitch, # 75992, that will fit your 2014 Ford Edge, I recommend the etrailer.com Ball Mount Kit for 2" Hitches - 2-3/4" Rise or 4" Drop - 7,500 lbs, # 989892. This ball mount kit will include a ball mount that will fit the 2 inch receiver opening on the Draw-Tite hitch. The ball mount will provide 2-3/4 inch rise or 4 inch drop. The kit will include a 2 inch trailer ball with a 7,500 lbs gross towing weight capacity and an 1-7/8 inch ball with a 2,000 lbs gross towing...
  view full answer...
• Trailer Hitch & Wiring Recommendation For 2022 Hyundai Palisade
  We do indeed have a trailer hitch receiver and wiring harness that fits your 2022 Hyundai Palisade. The best options for both the hitch and wiring harness are the following: - etrailer Trailer Hitch Receiver # e95ZR - Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # CU94FR The reason I like the # e95ZR hitch for your '22 Palisade is because it is easily the best value, you get the most for your money with this hitch. It also has a matte black finish, which...
  view full answer...
• What Hitch and 4-Way do You Recommend for Towing a Small Trailer on My 2022 Toyota Sienna?
  For a hitch for your 2022 Kia Telluride, I recommend the Draw-Tite Max-Frame Trailer Hitch Receiver - 2" # DT55MR. The Draw-Tite hitch is compatible with all Sienna models and comes with all mounting hardware required for a bolt-on installation. As far as weight capacity, the hitch has a 675 pound maximum tongue weight and a 4,500 pound gross towing rating. It also comes with an e-coat in addition to a powder coat that gives you even more protection against rust and corrosion. In order...
  view full answer...

Do you have a question about this Trailer Hitch Ball Mount?