Does the Bearing Kit BK3-100 Have a 225337375TB Grease Seal?

Question

Question:

My bearings match up however my seal number is 225337375TB. Would this kit work?

asked by: Dwayne

0

Expert Reply:

Yes, it will! The grease seal in the Bearing Kit item # BK3-100 has a 2.250" ID and a 3.376 OD.

expert reply by: Jerred H

0

Answer 1

Hey Mark, when in doubt the correct bearing info is what is listed on the bearings that are in your hub. So if you have a #25580 and a #15123 that is for sure the bearings you will need as a replacement. We have these bearings in a kit with the…

view full answer...

Answer 2

Hi Josh; those numbers correspond with a Dexter 6k brake assembly. You either need #BK3-100 or #BK3-110. I don't have a way of knowing which grease seal is on there now so you can either measure the inner diameter of your existing grease seal or…

view full answer...

Answer 3

We have two bearing kits that could fit for your Dexter 6,000 lb axles. The difference is the seal size. The part #BK3-100 is the kit that has the correct bearings and a seal with an inner diameter of 2.25 inches. This is most likely what you need.…

view full answer...

Answer 4

To replace your AL-KO seal part 363497 you can use the double-lip seal set #RG06-070. These have an inner diameter of 2.250-inches (to match your spindle diameter) and an outer diameter of 3.376-inches (to match the bore on your 12 x 2-inch hub/drum…

view full answer...

Answer 5

Hey Allen! Thank you for providing your axle information. According to Curt, the correct kit is the Bearing Kit, 15123/ 25580 Bearings, 10-36 Seal #BK3-100. If you need anything else don't hesitate to reach out in the comments below.

view full answer...

Answer 6

Bearing Kit #BK3-100 consists of bearings 15123 and 25580, matching races, grease seal and cotter pin. This kit is intended for a 6K axle. The same component parts are found in Lippert bearing kit 333950, also rated for a 6K axle. Two helpful…

view full answer...

Answer 7

According to my research the correct replacement bearings are parts #25580 and #LM67048 with the replacement seal being part #GS-2250DL. These are available in the Bearing Kit #BK3-300. Just make sure that you have these bearings and that your seal…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Does the Bearing Kit BK3-100 Have a 225337375TB Grease Seal?

Product Page this Question was Asked From

Continue Researching