Recommended Wheel Center Cap for Keystone RV with 16" 8 Lug Wheels

Question

Question:

Need wheel center caps for 16” wheel. 2013 keystone Rv 5th wheel 8 lug

asked by: Mike

0

Expert Reply:

It looks like most of our 16" trailer wheels with a 8 on 6-1/2" bolt pattern have a 4.88" or 4.9" pilot hole. If that is what you have then you can use the Lionshead Trailer Wheel Center Cap part # LHCS109-SI60C. Please note, we have no way to look up what exact wheels you have on your trailer so if you're looking for a specific style of center cap we would need a photo to assist further.

expert reply by: Conner L

0

Answer 1

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 2

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 3

Yes, the puck system used on the 2016-2019 Chevy/GMC trucks is different than the pucks used on the 2020 and newer trucks. So you would need a 5th wheel like the B&W Companion #BWRVK3710 for your 2020 GMC Sierra 3500 with an 8' Bed. If you…

view full answer...

Answer 4

You do not have to use a sliding 5th wheel hitch in a short bed truck. In many cases, truck beds shorter than 8 ft do not have enough clearance between the trailer and truck to execute sharp turns. This is why sliding hitches were invented. Due to…

view full answer...

Answer 5

Thank you for the photo of your 2016 Ram 3500's bed rail which sits 59-inches above ground. You are correct that the recommended minimum clearance between a bed rail and the underside of the trailer's overhang is 5 to 6-inches, as shown in…

view full answer...

Answer 6

As far as height adjustability and weight capacities the Curt Q20 #C16130 and the Curt A20 #C16140 are identical. They both have a Gross Towing Weight of 20,000 lbs, a Vertical Load Limit of 5,000 lbs, and a height range of 13-17 inches. When it…

view full answer...

Answer 7

Hi Bob; is your Patriot the slider #BWRVK3270 you looked at or the fixed #BWRVK3255? I know you said fixed mount hitch but since you looked at the slider I want to be sure. If it is the fixed hitch you can use the Adapter Rails for Curt 5th Wheel…

view full answer...

Answer 8

Most fifth wheel rails are made to the same industry standard dimensions. They aren't all though. If you measure 22 inches on center between the two rails and they look like the rails of the #RP30035 that you referenced they would be the industry…

view full answer...

Answer 9

While the best and most certain way to tell if your 2018 Ford F-250 has the puck system is to call your local Ford dealer with your VIN, it should be pretty easy to tell otherwise. If your bed looks like the accompanying photo - with four accessible…

view full answer...

Answer 10

Hey Silas! I really like the PullRite OEX SuperLite #PUL96ZR for towing with your 2025 Chevy Silverado 2500 for a few reasons; it fits directly to your puck system without an adapter, and then the weight of the hitch makes it much easier to get in…

view full answer...

Answer 11

Great questions! Reese actually makes the OEM puck system for Ford so if the 2022 F-250 is cheaper by a lot then I recommend going that route and installing the Under-Bed Rail and Installation Kit #RP87FR. The only thing you'll really be missing…

view full answer...

Answer 12

The Head Unit and R16 Roller Adapter #C16515 is more of an entry level fifth wheel head designed for a lower price point, whereas the A16 part #C16520 is a bit nicer with it's 2 piece jaw system that will provide better king pin contact which…

view full answer...

Recommended Wheel Center Cap for Keystone RV with 16" 8 Lug Wheels

Product Page this Question was Asked From

Continue Researching