How to Determine Correct Entry Door Lock

Question

Question:

Hello, I am looking for a replacement door lock and handle for my 2003 Fleetwood Terra, do you have one? Mine just spins after the key is in and the inside handle just hangs.

asked by: Dennis

0

Expert Reply:

Possibly; you'll need to take some measurements as there are no specific door locks and handles for any specific RV. So measure the door thickness and cut out. For example, if you have a door that is 1-1/4" to 1-1/2" thick and a cutout that is 2-3/4" wide x 3-3/4" tall you can use the Bauer Products Camper Door Lock # BA54FR.

I have added a link below to our entire selection of entry door locks.

expert reply by: Kyle S

0

Answer 1

Since your trailer has disc brake it will be very important that you pick out a actuator/coupler that is rated for that and not drum brakes as that is a lower pressure rating that won't work well. The 85841 is no longer made so it would be tough…

view full answer...

Answer 2

The only way to know if a door handle will fit your RV is to measure the cutout and get the corresponding fit. The Bauer Products Motorhome Door Lock - Black Item #BA64FR you linked to has a required cutout dimension of 5-1/4" wide x 4-1/2"…

view full answer...

Answer 3

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 4

I recommend the Bauer Products Camper Door Lock - Black #BA54FR. I feel they are a good quality brand and easy to operate. You can get them keyed alike by using the drop down menu before you add them to your cart. This particular version requires a…

view full answer...

Answer 5

Hey Mark, I did some digging and was able to find your Decker 1042 door latch, and it looks like it has a 2 7/8" x 3 3/4" cutout. While we don't have a direct replacement, we do have the Bauer Products Camper Door Lock #BA54FR, which…

view full answer...

Answer 6

Hey Kris, you'll want to measure the length from the very front to the very back of the fender as well as the overall width and height with height being the least important. For example, the part #HP52VR has the dimensions of 9" Wide x…

view full answer...

Answer 7

Yes, if you were to order three of the Global Link Baggage Lock Set part #GL34FR they would all show up using with the same key which is G391.

view full answer...

Answer 8

The closest option we have to the Command electronics Model 001-1050/1051 is the Gustafson RV LED Puck Light item #277-000489. It measures 4-3/8" diameter so the light is going to be slightly smaller 1/8" than your previous lights. I…

view full answer...

Answer 9

The #99 trailer spindle is typically found on 9,000 lb and 10,000 lb axles. This is not a spindle that we carry at this time, but I did find some of the measurements. I have attached a diagram showing the dimensions of a #99 spindle for you to check…

view full answer...

Answer 10

We do offer the Optronics trailer light #MC32RB for red and #MC32AB for amber. These lights will be extremely similar to the #MCL31RB that you mentioned, but they are a bit more square on the ends. The mounting holes on the #MC32RB are 3" apart…

view full answer...

Answer 11

The weld bracket on the top of the Ark Drop Down Corner RV Stabilizer Jack Kit #ARK34FR is 4.6063" long and the surface that would make contact is 1.8307" wide. The overall width is 2.8543" on the top. I have attached a dimensional…

view full answer...

Answer 12

The Bargman L-300 lock is no longer manufactured so a direct replacement lock is not available. The Redline Full Size Locking Steel Flush Door Latch #L3980 that you referenced has a similar handle lock design and should work nicely as a replacement.…

view full answer...

How to Determine Correct Entry Door Lock

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching