What Does Error Code 16 on Air Lift WirelessAIR Compressor System for Air Helper Springs Mean

Question

Question:

Hi, I have the airlift 5000, with the ez pump setup. I have an error message, compressor error 16. What does that mean

asked by: Travis F

0

Expert Reply:

I looked up the "16" error code on the Air Lift WirelessAIR Compressor System for Air Helper Springs part # AL74000EZ in the owner's manual for you. I found the following information:

Cause - Compressor hose disconnected from manifold or blockage in the compressor or system which is preventing air flow.

Solution - Check hose connections. Check for system blockages or frozen moisture in the air lines. Remove and reinstall the 15A fuse to reset the fault.

If you still continue to have issues with the system after the above is preformed, please let me know and I would be happy to assist further

expert reply by: Conner L

0

Javen

12/6/2024

Hi I double checked my lines and removed and re installed fuse and still getting the code #16

Reply

Kevin C.

12/10/2024

@Javen How long did you leave the fuse out for? Did you check the voltage to the compressor as well to ensure it's getting a full 12 volts? Checking power and ground to unit is always a good first step to rule out.

Reply

Answer 1

According to Air Lift, there are a few things that can cause this issue. The problem is likely an air leak between the manifold and the compressor or simply a weak compressor that would need to be replaced. To get the compressor running again so you…

view full answer...

Answer 2

You are definitely correct that both the B&W Companion #BWRVK3305 and the Reese M5 #RP30922 are fantastic 5th wheel hitches that will work well on your 2019 Ford F-350 but I do recommend going with the B&W Companion #BWRVK3305. The B&W…

view full answer...

Answer 3

No and you absolutely cannot use the Q-Series with a rotating pin box like the Turning Point. You will need a hitch that is compatible with sidewinders, like one from Reese. For your 2021 Ram 2500 with the puck system, you can go with the Reese M5…

view full answer...

Answer 4

Yes, the Replacement Center Section for Reese M5 5th Wheel Hitches item #RP30884 and the item #RP30894 can be used in the Ford Factory Puck System, the Ram factory puck system, and on industry standard rails. To mount it in the Ford prep package you…

view full answer...

Answer 5

Only certain B&W Companion 5th wheel trailer hitches are compatible with Sidewinder pin boxes like the RP61412. Basically if it is a Companion that mounts in the 4 pucks of a factory prep package then it can be used with a Sidewinder. But if the…

view full answer...

Answer 6

For a Bulldog 180 series jack you will need replacement drop leg pin #BD500177. It includes the spring, cotter pin, and washer. You should not have to remove the inner drop leg to replace the pin and spring. Start by pulling back on the pin. Then use…

view full answer...

Answer 7

According to the linked installation instructions, the pink wire you describe is for an optional feature that will allow the #AL74000 WirelessONE compressor system to make adjustments as soon as the ignition is turned on. Otherwise, the system will…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 11

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Answer 12

Thank you for the photo of your 2016 Ram 3500's bed rail which sits 59-inches above ground. You are correct that the recommended minimum clearance between a bed rail and the underside of the trailer's overhang is 5 to 6-inches, as shown in…

view full answer...

What Does Error Code 16 on Air Lift WirelessAIR Compressor System for Air Helper Springs Mean

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching