Availability of 5/8 Inch Flange Nut

Question

Question:

you have the trailer flange nuts 5/8?

asked by: Ted M

0

Expert Reply:

We have two options available for 5/8" flange nuts. We have the Flange Wheel Nut - 5/8" # 95188 with an overall flange diameter of 1-9/16" which is commonly used on hub-piloted trailer wheels. We also have the Dexter Dual Trailer Wheel Lug Nut with Swivel-Flange - Metric - Qty 1 # 6-118 which has an outer diameter of 1-5/16" and is designed for semi-trucks with 22.5" and 25.5" wheels.

expert reply by: Robin H

0

Answer 1

Standard trailer wiring circuits on 7-ways like the part #C58155 and #PK12706 are rated for up to 40 amps so if you wanted to use a 7-way like this to power a horn that is rated for 13 amps you certainly could.

view full answer...

Answer 2

I recommend going with a wheel like the Taskmaster Modular Wheel in White #TA36MR or Silver #TA35ZR. These wheels only have a 0.08" positive offset keeping the center of the Provider 235/75R17.5 Radial Trailer Tire #P35175 in line with the…

view full answer...

Answer 3

There are a few options but the Westlake 215/75R17.5 Radial Tire w 17-1/2" Lynx Aluminum Wheel #LHAS701 will not fit the 5/8" studs on your trailer. You can change your hubs to ones with a 9/16" studs to use these wheels. To do this I…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

The trailer brakes work on a separate circuit than the lights. You have a couple of options to control the electric brakes on the trailer. One option is to use an air over electric brake control, #HA100400C. This unit connects to the air brakes on…

view full answer...

Answer 7

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Availability of 5/8 Inch Flange Nut

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching