Replacement Brake Assemblies for 1987 VM Boat Trailer

Question

Question:

Looking for replacement brakes for my 1987 VM boat trailer . The brakes are 10 x 2 1/4 drum/hydraulic with 2 7/8 bolt pattern . Dont see this patern listed . Either the whole assembly or replacement shoes and wheel cylinders , thanks .

asked by: Craig H

0

Expert Reply:

Since you need 10 inch by 2-1/4 inch hydraulic brake assemblies that have a 4 bolt pattern that is 2-7/8 inches the drum brake kit part # AKUBRK-35-D would be what you'd need. The bolt pattern you mentioned is the standard 4 bolt pattern.

expert reply by: Jameson C

0

Answer 1

To replace your NOK AD2527E seal you can use #168233. It has an inner diameter of 1.688 inches and an outer diameter of 2.332 inches. Based on what I could find on the NOK AD2527E the inner diameter is the same and the outer diameter is 2.328 inches.…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 4

The determine the correct replacement leaf spring on your 2021 Coachmen 259FKDS you'll need to lift your trailer frame so the spring is hanging freely and then measure from center-eye to center-eye, then for the equalizer you need to measure…

view full answer...

Answer 5

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 8

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 9

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 10

There is no exact way to determine the leaf spring length. The best way to determine the length for a replacement is by measuring the existing leaf springs. The hanger distance and shackle length can help you get a good idea, but you're looking…

view full answer...

Answer 11

Hey Thomas, the most important factors for picking out a replacement leaf spring for a trailer are matching axle capacity and length. Getting the same amount of leaves in the spring pack is actually not a huge priority so I wouldn't worry too…

view full answer...

Answer 12

Hey Phil! Thanks for getting back to me with those measurements! We have a leaf spring that is an exact replacement but I am guessing it's the pricey one you referenced. It is the 4-Leaf Double-Eye Spring for 4,400-lb Trailer Axles - 25-1/4"…

view full answer...

Replacement Brake Assemblies for 1987 VM Boat Trailer

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching