How to Remove Elbow Air Fitting AL21848

Question

Question:

is there a specialty tool/socket to remove the 90 degree/elbow air fitting on an installed Load lifter 5000 air bag system or do I have to take the bags/plates apart to install the new fitting? Its an 11 mm wrench but I cannot get the wrench to completely turn in order to remove the fitting. The brackets impede the wrench.

asked by: Chris N

0

Expert Reply:

There isn't a special tool for removing the # AL21848 from the air bags. You'd need to use a wrench. If you can't make a complete revolution you'd need to take smaller turns based on the limited access.

You may need to remove the entire air bag from the brackets.

expert reply by: Jameson C

0

Answer 1

To remove the valve on the Air Lift LoadLifter 5000 Ultimate Air Helper Springs item #AL88338 you will need to remove the air spring from your truck. You can't turn that valve inside the bracket. Once off I recommend using the Replacement…

view full answer...

Answer 2

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 5

You do not have to use a sliding 5th wheel hitch in a short bed truck. In many cases, truck beds shorter than 8 ft do not have enough clearance between the trailer and truck to execute sharp turns. This is why sliding hitches were invented. Due to…

view full answer...

Answer 6

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Answer 7

As far as height adjustability and weight capacities the Curt Q20 #C16130 and the Curt A20 #C16140 are identical. They both have a Gross Towing Weight of 20,000 lbs, a Vertical Load Limit of 5,000 lbs, and a height range of 13-17 inches. When it…

view full answer...

Answer 8

Hi Duane, Air Springs are better for leveling loads and will typically give you a rougher unloaded ride quality so these might not be the best option for your setup depending on what your intended use is. Air springs are the best option when it comes…

view full answer...

Answer 9

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 10

Yes, the puck system used on the 2016-2019 Chevy/GMC trucks is different than the pucks used on the 2020 and newer trucks. So you would need a 5th wheel like the B&W Companion #BWRVK3710 for your 2020 GMC Sierra 3500 with an 8' Bed. If you…

view full answer...

Answer 11

Thank you for the photo of your 2016 Ram 3500's bed rail which sits 59-inches above ground. You are correct that the recommended minimum clearance between a bed rail and the underside of the trailer's overhang is 5 to 6-inches, as shown in…

view full answer...

Answer 12

Hey Jerry, GM moved the placement of their puck systems starting with 2020 models so you are correct that the pucks would have the hitch not sit directly over the axle. GM did the math and made sure that this placement wouldn't adversely affect…

view full answer...

How to Remove Elbow Air Fitting AL21848

Product Page this Question was Asked From

Continue Researching