How To Install the Spindle Nut on a 12,000 Pound Dexter Axle

Question

Question:

how much do i torque the spindle nut on a 12000 dexter axle? They have a washer, nut, lock ring and a jam nut

asked by: Cory O

0

Expert Reply:

I spoke to Dexter and they said there is a bit of a process for installing the spindle nut properly.

1. You will need to thread on the inner nut, rotate the hub, then tighten the nut to 100 foot pounds.
2. Loosen the nut to remove the torque, making sure not to rotate the hub.
3. Hand tighten the nut, then back it off 1/4 to 3/8 of a turn
4. Place the tang washer on the spindle and bend two tangs inward over the nut, This will keep the inner nut from turning while torqueing down the outer nut.
5. Install the outer nut and torque it to 100 to 175 foot pounds. Ensure that the inner nut does not turn while doing this. Bend two tangs from the tang washer over the outer nut to secure it.

Once all that is done you should end up with anywhere from .001 to .010 inches of play. This is also the recommended tolerance that Dexter suggested.

expert reply by: Lazer S

0

Answer 1

The Dexter 12K oil bath axles can be changed over to grease without any issues. The oil does keep the bearings lubricated well, but there is a much higher risk of leaking which leads to a much higher risk of failure. I'd personally move to grease…

view full answer...

Answer 2

Hi Armando, Thanks for the photo showing the sticker on your trailer, and from what I was able to find you have 10,000 lb Dexter axles with disc brakes. You'll want to verify this just to be certain, but for replacement 10k disc brake pads you…

view full answer...

Answer 3

The torque for the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles - 12" - 5 Spoke Utility #8-174-5UC3 is not specified by the manufacturer. For 9/16 inch studs, the typical lug nut torque will be 120-140 ft lbs based on most…

view full answer...

Answer 4

Are there any visible signs of wear on the magnets like exposed windings then that would indicate they need replacing. Magnets can go bad without showing visible signs of wear though. To see how to troubleshoot them check out the help article I…

view full answer...

Answer 5

To convert electric drum brakes to electric-over-hydraulic disc brakes you will need disc brake assemblies, a brake line kit and an electric over hydraulic actuator. For disc brake assemblies, the Kodiak Disc Brake Kit #K2R1058D13 kit is what I…

view full answer...

Answer 6

Thanks for reaching out, Arnold! When replacing the bearings and races you want the bearings to sit flush inside the race. Be sure the race is completely clean and there isn't any debris keeping it from sitting flush, and that you have the…

view full answer...

Answer 7

I checked with Dexter and here is the information on tightening the spindle nut on your 8K axle: 1. After placing the hub, bearings, washers, and spindle nut back on the axle spindle in reverse order as detailed in the previous section on hub…

view full answer...

Answer 8

Since you have replaced your brake assemblies and flexible brake lines, and have bled the system, the sticking brakes on your horse trailer are most likely caused by the electric-over-hydraulic actuator itself or its main steel brake line. It is…

view full answer...

Answer 9

In order to remove the hub/drum on your trailer you will want to first remove the spindle nut. Once the spindle nut is removed you are going to want to take a hammer and tap the outer portion of the drum as well as the hub face a few times to break…

view full answer...

Answer 10

The spindles can be replaced. However, they will need to be welded by a certified welder. They use special jigs so that it is concentric and square on the axle or it can cause problems with uneven tire wear and wheel tracking. I've linked our…

view full answer...

Answer 11

According to my research, the correct replacement rotor for your Dexter 12K Axle (Non-ABS) is the Replacement Rotor for Dexter Disc Brakes part #070-006-01 which measures 11" in diameter. The Dexter 10K and 12K axles will both use the same…

view full answer...

Answer 12

The Dexter Spindle Nut #6-183 used with your 50mm Nev-R-Lube bearing #31-71-3, requires 145 to 155 ft/lbs of torque, according to the manufacturer's specifications. See attached diagrams for step by step instructions.

view full answer...

How To Install the Spindle Nut on a 12,000 Pound Dexter Axle

Continue Researching