Smallest Trailer Tire and Wheel with Load Range E

Question

Question:

whats the smallest diameter and the widest 16low profile tire you can get in a trailer tire E rating

asked by: Jake

0

Expert Reply:

The Load Range E capacity for each tire size represents a different weight capacity but the smallest tire and wheel we offer with the Load Range E is the part # AM3H480 which is 8.4 inches wide and 20.4 inches tall.

expert reply by: Jameson C

0

Answer 1

In your case I do recommend going with the larger 205/65-10 tire size for a few reasons; you'll have a higher load rating and you'll have a higher speed rating. I will say it's important to make sure you have the tires filled to the…

view full answer...

Answer 2

Based on my research, the 20.5x8.0-10 tire size equates to the current size listing of 205/65-10. With this in mind, I recommend looking at the Kenda 205/65-10 Bias Trailer Tire with 10 Inch White Wheel #AM3H480. This bias ply tire is mounted to a…

view full answer...

Answer 3

The Kenda K353 Bias Trailer Tire - 5.30-12 - Load Range C #AM10066 has a speed rating of 65 mph and like you mentioned a max load capacity of 1,045 lbs at 80 psi. However you should make sure that the combined maximum load rating is higher than the…

view full answer...

Answer 4

The 205/65-10 and the 20.5 x 8-10 would be very close in size. Assuming that 20.5 is the diameter of the tire and 8 is the width. The Kenda 205/65-10 Bias Trailer Tire with 10 inch White Wheel, #AM3H390, for example, is 8.3 inches wide with a…

view full answer...

Answer 5

The modern size equivalent of the 20.5x8-10 that you have currently would be the same size tire that is on the #AM3H340 that you referenced, 205/65-10. As long as the bolt pattern of your current hubs are 4 on 4 inch the wheels of this would bolt up…

view full answer...

Answer 6

The 18.5x8.5-8 is actually an old tire size that is not used much anymore. The closest metric size to your existing tire would be 215/60-8. Your wheel most likely has a 5-on 4-1/4 inch bolt pattern (see link), you will want to make sure that the bolt…

view full answer...

Answer 7

The modern size for the 20.5x8x-10 is 205/65-10 which we offer that with a rim that has a 5 on 4-1/2 inch bolt pattern is part #AM3H480. For a similar setup with a 4 on 4 inch bolt pattern you'd need the #AM3H460.

view full answer...

Answer 8

Wheel bolt patterns are defined by two numbers: the first being the number of lug nuts and the second being the diameter of the circle the lug nuts are arranged in. So a 5 on 4-1/2 bolt pattern is 5 lugs arranged in a circle that is 4-1/2 inches in…

view full answer...

Answer 9

As you do not look to have any fenders on your trailer, you may be able to go with a larger tire and wheel combo. However, you do want to have at least 3 inches from the top of the tire to the bottom of the closest part of either the trailer or the…

view full answer...

Answer 10

Yes, the 3" length of the shank is measured from the end of the spine to the mounting flange of the Trailer Idler Hub Assembly #52655IEU. I have noted that and the 2-1/4" diameter in the attached photo for you to reference as well. This…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Smallest Trailer Tire and Wheel with Load Range E

Product Page this Question was Asked From

Continue Researching