Wiring Kit for Powering Winch at Rear or Tacoma

Question

Question:

Good day, I have a Superwinch to go. I need to use it at the rear of my Tacoma. Is there a wiring kit for the rear?

asked by: Joe B

0

Expert Reply:

We have wiring kits for winches like the part # BDW20206 which gives you a 20 foot long wiring setup you can run from the front of your Tacoma to the back of the vehicle like you are needing. The wiring is 2 gauge which can handle the higher amperage draw of winches.

expert reply by: Jameson C

0

Answer 1

I recommend the Bulldog Winch Winch Cover - Standard Truck Winches #BDW20046, It has a stretchy elastic bottom, and polyurethane interior coating. It is a quick and easy install or removal.

view full answer...

Answer 2

The dimensions for the Bulldog Winch Winch Cover #BDW20046 are 21" long x 8" x wide x 11" tall. Attached is a review video for you to check out.

view full answer...

Answer 3

The Bulldog Winch Trailer Winch #BDW15020 you referred to has the power unit over the motor, as I've pointed out in the accompanying photo. Because of that there is a specific cover you need, the Bulldog Winch Neoprene Cover - Truck Winch w/…

view full answer...

Answer 4

The Superwinch Talon Series Off-Road Winch is a very nice winch that as you stated draws 345 amps at the 14,000 lb line pull. In order to give you the best option we have, I recommend the Bulldog Winch Rear Wiring Kit - Quick Connect to Terminal End…

view full answer...

Answer 5

It sounds like you need a quick-disconnect winch wiring kit that includes the parts to allow use on both the front and rear hitches installed on your 2017 Wrangler Unlimited. You can use kits #BDW20206 and #BDW20205. Both have quick-disconnect…

view full answer...

Answer 6

The base plates and front mount hitches (which you would use to mount a winch) install at the same places on the frame of the 2015 Jeep Wrangler Unlimited so you cannot have both at the same time. I recommend putting a winch at the back of the Jeep.…

view full answer...

Answer 7

Yes, the Superwinch Hitch Mounted Winch Mounting Plate with Handles #SW2050 is compatible with your Superwinch S9000 front mount winch. Attached is a review video for you to check out.

view full answer...

Answer 8

The Bulldog Winch part #BDW10031 that you referenced would fit well in the Bulldog Winch Receiver Mount Kit #BDW20155. I attached a review video for the hitch for you to check out as well.

view full answer...

Answer 9

I have a solution for you to connect the Bulldog Winch Trailer Winch #BDW10039 to your vehicle's battery, but it will not work well for you to connect the winch to the vehicle's 7-way connector. The highest gauge wire a 7-Way connector is…

view full answer...

Answer 10

For an electric winch like the Bulldog Winch Standard Series Off-Road Winch #BDW10043, you can use a receiver mount like the Bulldog Winch Receiver Mount Kit - 2" x 2" #BDW20155. This makes location easy and you can absolutely add the quick…

view full answer...

Answer 11

We have exactly the parts you are looking for. Starting with the winch I recommend the Bulldog Winch Standard Series Off-Road Winch - Synthetic Rope #BDW10046 would be a great option that has the 12000lb rating you are looking for, and automatic…

view full answer...

Answer 12

I reached out to my contact at Bulldog Winch who said that while the Bulldog Winch Off-Road Winch Mounting Plate #BDW23001 doesn't have a max weight capacity it is strong enough to safely recover your 2019 Toyota Tacoma. Essentially it can handle…

view full answer...

Wiring Kit for Powering Winch at Rear or Tacoma

Product Page this Question was Asked From

Continue Researching