Replacing Factory Hitch on 2006 Toyota Tundra
Question:
I spoke with a Toyota dealership service center today about replacing my 2006 Toyota Tundra hitch which is rusted out. They indicated that it had to be replaced with a Toyota Hitch $1600 because it is part of my frame. Not sure I believe that. Looks like I should be able to unbolt it and replace it with part #13184? Would you be able to confirm that this part number will fit my Toyota and provide a solid hitch for me to pull my travel trailer? Thanks.
asked by: Kenny I
Expert Reply:
The answer to your question will depend on if you have the actual 'factory' hitch which is incorporated into the bumper brackets or the 'dealer installed' hitch which is just bolted to the frame.
If you have the dealer installed hitch, you can remove it and replace it with the # 13184 you'd looked at. If you have the actual factory hitch, you'll need to replace the rear bumper with one for a vehicle that doesn't have the factory hitch.
If you do replace the hitch, you'll want to give the rear frame a careful look over to ensure the frame members are still sound.
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 500 lbs TW
- 5000 lbs GTW
- 7500 lbs WD GTW
- 2 Inch Hitch
- 750 lbs WD TW
- Concealed Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Trailer Hitch
- Shop: Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Video: Mount: Draw-Tite Max-Frame Trailer Hitch Receiver on a 2002 Toyota Tundra
- Q&A: Trailer Hitch for a 2006 Toyota Tundra SR5 with Factory Towable Bumper
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class V - 2"
- Shop: Trailer Wiring
- Shop: Draw-Tite Ultra Frame Trailer Hitch Receiver - Custom Fit - Class IV - 2"
- Q&A: Recommended Hitch for a 2008 Toyota Tundra
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Article: My Trailer Hitch Doesn't Fit
- Video: Mount: Curt Trailer Hitch Receiver on a 2013 Toyota Tundra
- Video: Trailer Wiring Harness Installation - 2008 Toyota Tundra
- Video: Setting up the Draw-Tite Ultra Frame Trailer Hitch Receiver on a 2013 Toyota Tundra
- Video: DIY Install: Draw-Tite Ultra Frame Trailer Hitch Receiver on your 2010 Toyota Tundra
- Shop: Hopkins Plug-In Simple Vehicle Wiring Harness for Factory Tow Package - 7-Way and 4-Flat Connectors
- Search Results: stabilizer jack pads
- Video: How to Install: Curt Trailer Hitch Receiver on your 2002 Toyota Tundra
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Q&A: Is there a Hitch for the 2013 Toyota Tundra's that Have a Factory Hitch?
- Q&A: Can Curt Trailer Hitch Receiver be Installed on a 2011 Toyota Tundra After Factory Hitch is Removed
- Shop: Suspension Enhancement
- Search Results: wheel chock
- Q&A: How Much Weight Can I Tow With A 2013 Toyota Tundra CrewMax
- Q&A: Trailer Hitch that Fits 2002 Toyota Tundra with Towable Bumper
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Video: Finding the Right Trailer Wiring Harness
- Search Results: trailer hitch
- Search Results: trailer wiring
on Trailer Hitch
