Replacement Jack Solution for 1992 Four Winns Horizon 190 Solution

Question

Question:

I’m looking for a bolt on boat trailer jack for a 1992 Four Winns Horizon 190. The bolt pattern on the trailer is 4” X 2.75”. What do you recommend. Thank you for your help.

asked by: Mark L

0

Expert Reply:

Since we don't have a jack that is designed to attach to mounting holes that are 4 inches by 2-3/4 inch your best option will be to weld the mounting plate of the Fulton F2 part # F1413050334 to your trailer frame so that you can then bolt this jack in place.

expert reply by: Jameson C

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

Hey Piotr, thanks for reaching out! The weight ratings between the Curt Trailer Hitch Receiver #C94WR and Towsmart Trailer Hitch Receiver #TS96VR that fit your 2025 Kia Sportage are determined by the testing done according to those manufacturers. I…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

Hey JD, The Weigh Safe Hitch w/ Built-In Scale for 2.5" Hitch #WS88RR uses hitch pic lock #WS54CR, which has a shear strength capacity of 45,000lbs according to Weigh Safe.

view full answer...

Answer 6

Hello Paul, thanks for reaching out. The inside dimension of the Curt Heavy-Duty Dual Ball Attachment for Weight Distribution Shanks #C29NR is 2". It will work with any standard weight distribution shank. I edited a picture to illustrate.

view full answer...

Answer 7

Curt recommends the use of 250 ft/lbs of torque when tightening the nuts of their hitch balls with a 1 inch diameter shank like the part #C40034 that you referenced. The general rule is for a 3/4" shank tighten to 150 ft/lbs For a 1" shank…

view full answer...

Answer 8

Hey JC, thanks for reaching out! The B&W Tow & Stow 2-Ball Mount #BWTS20066BMP is definitely compatible with the MultiPro tailgate on your 2024 GMC Sierra 2500, but the only one available to fit exactly with a 2-1/2" hitch receiver is…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

Hey Carl! How much does the Weigh Safe weigh? With all of the parts put together the #WS88RR weighs 35-1/2 lbs. If you need anything else don't hesitate to reach out in the comments below.

view full answer...

Answer 11

Hello Tim, Are you asking if you can back up with just the head installed on the Weigh Safe True Tow Weight Distribution Hitch #WS79VR, when you put the trailer coupler onto the ball? If so, then yes because at that point it is really just a ball…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Replacement Jack Solution for 1992 Four Winns Horizon 190 Solution

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching