Trailer Hitch Option for 2006 Monaco La Palma Motorhome

Question

Question:

I have a 2006 Monaco la palma and would like to put a better receiver hitch on it do you have any options

asked by: John T

0

Expert Reply:

There is a potential option for a trailer hitch for your 2006 Monaco La Palma motorhome, though there are no custom-fit hitches for this vehicle, which was built on a Roadmaster motorhome chassis.

Instead, you may be able to use the Multi-Fit Motorhome Trailer Hitch # 5350 which will fit so long as your '06 Monaco has a chassis that measures between 24" and 46" wide so you will need to take a quick measurement to determine if it will fit.

This is a 2" hitch with a 5,000 lb towing capacity and 500 lb tongue weight capacity; I have added a link to a video review as well as a link to the installation instructions for you to take a look at.

expert reply by: Kyle S

0

Answer 1

The Draw-Tite Ultra Frame Trailer Hitch Receiver, part #41938 you referenced is not designed for a motorhome, but we do have a solution for you. I recommend a trailer hitch like part #13703. This is designed for motorhomes that have frame width…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

The overall width of the Buyers Products Class 4 Service Body Long Hitch Receiver #3371801055 that you referenced 44-1/2 inches. I attached a picture that has that dimension and a few others listed as well.

view full answer...

Answer 5

I would be happy to and thanks for the pictures! The B&W Heavy-Duty Trailer Hitch item #BWHDRH25122 measures 5.4" from the top of the frame brackets to the top of the receiver and 19-1/2" to the back of the receiver from the last bolt.…

view full answer...

Answer 6

The crosstube and the hitch tube of the Draw Tite Multi Fit hitch part #82201 that you referenced is 2-1/2 inch by 2-1/2 inch.

view full answer...

Answer 7

Box trucks typically have a rear section that hangs below the truck frame quite a bit which makes installing a hitch a bit difficult. I spoke to my contacts at Curt and Reese and the only styles of hitches that can be made to fit a box-truck body…

view full answer...

Answer 8

The best option we have for you to add a trailer hitch on your 1998 Shuttle Bus is the Draw-Tite Class IV Weld-On Ultra Frame Trailer Hitch Receiver #41990. This hitch can be installed with either 16 inch brackets #4916 or 7 inch brackets #4907. In…

view full answer...

Answer 9

For your Ford F-53 chassis I recommend taking a look at the Draw-Tite Multi-Fit Trailer Hitch #5350. This is an adjustable hitch specifically designed for applications like yours as it can fit frame widths that measure between 24 and 46 inches. It…

view full answer...

Answer 10

Since there aren't any custom fit hitches available you'll just need to pick up a weld-on cut-to-fit hitch like the Draw-Tite Ultra Frame Service Body Trailer Hitch Receiver #41990-07. This comes with brackets that provide a 7" drop but…

view full answer...

Trailer Hitch Option for 2006 Monaco La Palma Motorhome

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching