See what our Experts say about this Draw-Tite RV and Camper Hitch

• Receiver Hitch Recommendations For A 2021 Flagstaff E-Pro 19 FBS
  To add a receiver hitch for a bike rack you'll actually connect the hitch to frame of your RV and not use the bumper as most aren't rated to hold the weight of a bike rack and bikes. You'll need to measure from beam to beam to see what frame distance you have. The Multi-Fit Motorhome Trailer Hitch, 24" - 46" wide Item # 5350 you linked to will attach to a frame distance of 24" to 46". We also offer the Curt Adjustable Trailer Hitch Receiver - 18"-51" Wide - 2" Drop - Class III - 2"...
  view full answer...
• Multi Fit Hitch for RV with 5,000 lb Towing Capacity
  The Draw Tite hitch part # 5350 is a multi fit hitch designed for RVs like your motorhome and has the capacity you are wanting. As long as the width of your frame is between 24 and 46 inches this would fit and work great. The other options we have like the # 13703 which fit a wider frame width range don't have the capacity.
  view full answer...
• Recommended Trailer Hitch for a 2011 Collins Half School Bus With a 42" Wide Chassis
  Hey Cameron, I recommend checking out the Multi-Fit Motorhome Trailer Hitch # 5350. This is a multi fit trailer hitch that will fit chassis 24" to 46" wide so it'll work perfect with your 43" wide chassis. This hitch is compatible with a weight distribution system, has a max weight capacity of 5,000 lbs, and has a max tongue weight capacity of 500 lbs.
  view full answer...
• Recommended Trailer Hitch for Ford F-53 Chassis with 31-1/2 Inch Frame Width
  For your Ford F-53 chassis I recommend taking a look at the Draw-Tite Multi-Fit Trailer Hitch # 5350. This is an adjustable hitch specifically designed for applications like yours as it can fit frame widths that measure between 24 and 46 inches. It will provide you with a 2 inch receiver opening and a towing weight capacity of 5,000 pounds. You can either use the included hardware to bolt the hitch to the frame or have it welded on for a no-drill installation. I have attached a short...
  view full answer...
• Recommendation For Adding A Hitch To A 1996 Toyota Prado JDM
  I may have an alternate option available that will require drilling to get installed, but with your 1996 Toyota Prado not being an American market vehicle, I cannot confirm the fit of any hitch we carry. I did include diagrams for the Curt # 13445 and # C13087, as well as the Draw-Tite # 75091 for you to take a look at though. With that being said, check out the Draw-Tite # 5350. This is technically designed for use on an RV, but may suit your needs very well. It will definitely fit your...
  view full answer...
  
• Recommended Trailer Hitch for 2003 Ford E450 Chassis
  The Draw-Tite Ultra Frame Trailer Hitch Receiver w/ Cast Center # 41945 is a confirmed fit for 2000 - 2003 Ford Van Full Size and may fit your chassis. I recommend checking the dimensions of the frame holes as this hitch's mounting holes are 38-1/2 inches on center. This hitch is rated for 1,500 lb tongue weight and 10,000 lbs towing. This hitch will be dependent on the chassis and will not work if it has been extended. Your alternative if you don't have these holes is the Multi-Fit...
  view full answer...
  
• Recommended Trailer Hitch For A 1996 Toyota Land Cruiser Prado
  I may have another option available, but as all the hitches we carry are for US market vehicles, I cannot confirm the fitment on a Japanese market 96 Toyota Land Cruiser Prado, unfortunately. However, I did include a quick diagram of how the Curt # C12181 hitch will measure as it may still work for your vehicle. If these measurements do not add up though, the only other thing I can recommend is something like the Draw-Tite Multi-Fit # 5350. This will fit a frame that is 24" to 46" wide...
  view full answer...
  
• Trailer Hitch Receiver for Motorhome on 2006 Ford F-53 Chassis
  There is a potential option so you can install a trailer hitch on your Monaco Monarch, though there is nothing that is a direct, custom-fit for a 2006 Ford F-53 chassis, so you will need to measure the frame of your chassis to find the right fit. If your frame measures 24" to 46" wide you can use the Multi-Fit Motorhome Trailer Hitch # 5350. If your frame measures 47" to 71" wide you can use the Multi-Fit Motor Home Trailer Hitch # 82201. Each of these hitches are bolt-on options that...
  view full answer...
• Recommended Trailer Hitch Receiver For 2005 Ford E-450 Chassis
  I reached out to my contact at Draw-Tite and for the 2005 Ford E-450 there isn't a custom fit hitch available. There is also not a Class IV or Class V hitch available from any of our manufacturers for your chassis. The largest hitch I can recommend is the Draw-Tite Multi-Fit Motorhome Trailer Hitch, 24" - 46" wide # 5350 that has a 5000 lb weight capacity but that bumps up to 6000 with weight distribution. The tongue weight rating when using weight distribution jumps from 500 lbs,...
  view full answer...
• Replacement Trailer Hitch Options for a 2008 Coachmen Cross Country 38' Motorhome
  The mounting brackets on the Curt Class 5 Universal Weld-on Hitch # C47CR do need to be in that upright position so while this hitch can technically fit with your motorhome chassis, you'll need to get creative on how to properly weld the brackets to the frame. For an alternative option with the brackets that are in the same orientation as your frame brackets I recommend the Multi-Fit Motorhome Trailer Hitch # 5350 which fits 24" - 46" wide frames and is rated for 5,000 lbs towing. If...
  view full answer...
  
• Trailer Hitch with 2 Inch Receiver for a 2010 Coachman 5th Wheel Trailer
  For an RV hitch that you can install on your 2010 Coachman 5th wheel trailer I recommend Ultra-Fab trailer hitch # UF35-946403. This hitch fits frame widths of 47 inches to 77 inches so it will fit your 66 inch frame (measured between the rails). Frame width in reference to this hitch is measured from the outside of one frame rail to the outside of the other. It is designed to weld directly to the bottoms of the frame rails. If you do not think this design is going to work then the most...
  view full answer...
• Recommended Hitch for RV/Motorhome with 2004 Ford E-450 Van Chassis
  I have a solution for you, but the two hitches you were looking at will not fit your Motorhome. While there is no custom fit hitch for your chassis, we do offer a few universal options. One type of motorhome hitch is the Draw-Tite # 5350, which can accommodate the mounting hole spread of 22 inches. If you instead have an I-beam or C-channel frame the Curt # 13703 would be what you want for your 38-5/8 hole spread. The one I recommend for the receiver being in the placement that you...
  view full answer...
  
• Recommended Trailer Hitch Receiver For A 1992 Ford E-350 Shuttle Bus
  Hi Tad, Based on the dimensions you provided I recommend going with the Adjustable Width Trailer Hitch Receiver for RVs, 18" to 51" Wide # C13702. This would mount under the frame with the receiver tube sitting roughly 2" below the frame. If you need an additional 2" (4" total) to clear any rear bumper/fascia then you can go with the # C13701 instead. These hitches fit frame widths from 18" - 51" and any excess can be cut off of the crosstube with a chop saw to fit. There are a few other...
  view full answer...
• Front Mount Hitch with 32 Inches Between Mounting Holes
  Because all of our front mount hitches are custom fit to a specific year, make and model of vehicle, the mounting hole distance is not a spec that's listed or typically needed on them. If you're not using the hitch for a specific vehicle but rather for special fabrication project, you may be able to use one of our universal RV hitches like # 5350 which is adjustable to fit frames 24 to 46 inches wide. The Multi-Fit Motorhome Trailer Hitch has the highest capacity (500lb TW and 5,000lb...
  view full answer...
• Is There a Trailer Hitch for a 1992 Cadillac Brougham
  I may have an option for you but there aren't any custom fit trailer hitches for a 1992 Cadillac Brougham. Therefore, in order to attach a trailer hitch you'll need to do some modifying and or fabricating of your own. The best option we have for this is the Multi-Fit Motorhome Trailer Hitch part # 5350. The reason this option is best is because the width of the hitch can be adjusted for your frame and the two bolt mounting design would be pretty easy to mirror onto the frame as well. The...
  view full answer...
• Front Mounted Trailer Hitch Receiver for 1985 Dodge Van
  There aren't any front-mounted trailer hitch receivers that are custom designed to fit for a 1985 Dodge B350 and your bumper is not structurally strong enough to work with the Curt RV Bumper 2" Trailer Hitch Receiver # E-100. What that means is the only option that might work is a universal, adjustable-fit hitch such as the Adjustable Width Trailer Hitch Receiver for RVs, 22" to 72" wide # 13703 or the Multi-Fit Motorhome Trailer Hitch, 24" - 46" wide # 5350 or 47" - 71" wide # 82201. These...
  view full answer...
  
• Trailer Hitch for 2009 Ford E350 Box Truck
  Box trucks typically have a rear section that hangs below the truck frame quite a bit which makes installing a hitch a bit difficult. I spoke to my contacts at Curt and Reese and the only styles of hitches that can be made to fit a box-truck body like yours are multi-fit RV hitches like the # 41990 that has a 16k capacity. This is a weld on hitch that would require either the 7 inch drop brackets part # 4907 or the 16 inch brackets part # 4916.
  view full answer...
• Multi-Fit Hitches Available for a Class C Motorhome
  There are other multi-fit hitches available for your 2014 Mini Wini 31K class C, but the Blue Ox Specialty Trailer Hitches # SC9000 will only work on Class A motorhomes. Check out the Multi-Fit Motorhome Trailer Hitch # 5350. This hitch has a 500 lb tongue weight rating and 5,000 lb trailer weight capacity that can fit frame widths between 24 and 46 inches. If that range isn't large enough you could also check out the Curt Hitch part # 13703 as this hitch can fit frames from 22 inches...
  view full answer...
• Is There a Class IV or V Hitch for a Motorhome
  I do have an option for you but they don't offer custom fit hitches for motorhome chassis. The best option is a universal fit hitch which are typically only available in class III weight rating ranges. For this, I recommend the Multi-Fit Motorhome Trailer Hitch part # 5350 or part # 82201 depending on frame width. The higher capacities cannot really be achieved without fabrication.
  view full answer...
• Hidden Hitch Trailer Hitch Receiver Weight Capacity Maximum.
  I reached out to the manufacturer of Hidden Hitch which has been discontinued and replaced with Draw-Tite in most instances. The model of hitch you have has been discontinued but I was able to get the specs for you from the manufacturer. There is not a rating for use with weight distribution systems so you will be limited to the 5,000 lb capacity. If you want a system rated for 6,000 lbs (with weight distribution), I recommend the Draw-Tite Multi-Fit Motorhome Trailer Hitch, 24" - 46"...
  view full answer...
  
• What Does The Reese 36041 RV Hitch Fit?
  The part number 63041 that you mentioned is a trailer hitch receiver for RV's that is no longer available. I reached out to my contact at Reese and it was an OEM option that was discontinued in 2013. There is not a fit guide specifically for that hitch other than it is only for RV use. It has a gross towing rating of 3,500 lbs with a max 300 lbs tongue weight rating. If you want to replace it, I recommend the Multi-Fit Motorhome Trailer Hitch, 24" - 46" wide # 5350 made by the same...
  view full answer...
• Installation of the Multi-Fit Motorhome Trailer Hitch, Item # 5350, No Welding Required
  Welding is not required for installation of the Multi-Fit Motorhome Trailer Hitch, item # 5350. Once you have the tube cut to length, be sure it is centered on the vehicle, you will need to drill 1/2 inch holes in the cross tube to secure it to the brackets. There are holes in the receiver portion of the brackets to use as a template for drilling the cross tube (see instructions).
  view full answer...
• Recommended RV Trailer Hitch For Motorhome with C-Channel Frame
  I do have an option for you but the Reese Reese Multi-Fit Motorhome Hitch part # 5350 is not confirmed to work with a C-Channel frame. I recommend to use Adjustable Width Trailer Hitch Receiver for RVs part # C13702 which is designed to fit 18-51 inch wide frames. Curt has confirmed this hitch will work well on C-Channel frames like what you have on the Jayco Greyhawk 26ss. I have attached a video for your reference.
  view full answer...
• Front Hitch Option For A 2023 Ford F-550
  I do have a potential option for you, however the Draw-Tite Front Mount Trailer Hitch # 65076 is not confirmed to fit the 2023 Ford F-550. Since there is no custom fit option, your best option is going to be with a universal model like the Draw-Tite Multi-Fit Trailer Hitch # 5350 that will require some drilling. This particular hitch features adjustable brackets that allow it to fit frame rails that are 24" to 46" wide. The brackets will get bolted to the frame to provide you with a crosstube...
  view full answer...

Do you have a question about this RV and Camper Hitch?