Will Using Timbren Helper Springs Help to Reduce Trailer Sway

Question

Question:

I have a 2013 F250 Powerstroke diesel crewcab and are towing a 8,000lb travel trailer 760lb tongue. We have noticed an increase in sway compared to our previous gas Chevy 2500HD same trailer, hitch equip, etc. Will the Timbrens actually decrease the sway we are now experiencing? This truck does sag considerably more than the Chevy did, so I know that plays a factor as well.. Thanks!

asked by: RP

0

Expert Reply:

If your trailer is a bumper pull and not a 5th wheel or gooseneck trailer then the best way to combat trailer sway and rear end sag is to use a weight distribution system. Timbren springs on your 2013 Ford F-250 will help reduce the sag and will help with side to side body roll of the truck but will not do as much for trailer sway as a weight distribution system with built-in sway control.

If you are not currently using a weight distribution system I recommend the Reese Strait-Line # RP66084 with ball # 19286. This system is rated for 600 to 1,200 pounds tongue weight. It comes with dual-cam sway control that, when properly set up will prevent trailer sway from starting.

If it is a 5th wheel or gooseneck then if the trailer is not level it can lead to an increased chance of sway. This is because the weight of the trailer is not evenly distributed to its axles and to the hitch in the truck. Too much or too little pin weight in other words can lead to sway issues.

expert reply by: Michael H

0

Answer 1

If you use the spacer of the Timbren kit part #TFRTT350J it will engage the springs sooner. In general this is going to give you more support at a sooner time when the suspension begins to be compressed. What this ends up doing is creating a much…

view full answer...

Answer 2

The bump stop of your 2020 Chevy Silverado 2500 actually is not held in with a bolt and to remove it you would just need to pry it out.

view full answer...

Answer 3

Beautiful truck and travel trailer you have there! Airbag suspension enhancement is the best way to reduce rear sag and improve the handling of your truck when you are pulling a heavy load, such as your 40 foot Montana 5th wheel. You can then deflate…

view full answer...

Answer 4

Most of the time when a tow setup is porpoising with a weight distribution system all you have to do is add a bit more spring bar tension to minimize the porpoising. With an Equalizer system you would need to angle the spring bars down further to add…

view full answer...

Answer 5

Sway controls are designed to be used in situations where sway is a direct result of some type of road condition, like high winds or large vehicles passing. If you have sway with a trailer under normal towing conditions, sway control will most likely…

view full answer...

Answer 6

If the leaf springs on your 2005 GMC Sierra are worn out then the Timbren Rear Suspension Enhancement System part #TGMRCK15S will engage more frequently. This would help your leaf springs from wearing further but this may also have an adverse affect…

view full answer...

Answer 7

We've spoken with Furrion about your same issue with another customer and they informed us that the 88 error code on your Furrion fireplace means the blower fan is overheating. You want to make sure the inlet and outlets of the fireplace are free…

view full answer...

Answer 8

Timbrens like the #T28MR that you referenced are not known to make a huge difference with trailer sway. If you are experiencing trailer sway most likely it's due to improper trailer loading which you can fix by moving forward any cargo weight in…

view full answer...

Answer 9

The #TDR1500DS Timbren Rear Suspension Enhancement System will help reduce or get rid of the sag you are experiencing with your 2017 Ram 1500. These will also help improve overall handling and give you a more comfortable ride by absorbing road shock…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Will Using Timbren Helper Springs Help to Reduce Trailer Sway

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching