Most Common Trailer Brake Line Fitting Size

Question

Question:

I need a brake hose for my boat trailer. tracker boat, trail star trailer, manufactuer- Fabrique par, tracker marine. ser. 4TM14UG244B001006 YEAR 2003 HELP IF YOU CAN THANKS

asked by: Mike

0

Expert Reply:

How long of a line do you need? Do you know what size you need? The most common size is 3/16 inch like part # BH-3MFS-4-5 which is 54 inches long.

expert reply by: Jameson C

0

Answer 1

The DB-42 is an older style of UFP 3,500 lb axle disc brake components. The Kodiak kits like the part #K2HR35D will fit in replacement of that and would be an upgrade so this would be a great solution. It comes with everything you'd need to…

view full answer...

Answer 2

Typically trailers will carry more of their weight on the front of the trailer, so you would want to put the brakes on the front axle as it will most likely carry more weight while braking. Also, when braking, weight will shift forward from the…

view full answer...

Answer 3

The Dexter Brake Actuator part #099-175-20 replaced the Titan 60 that has a master cylinder with a fitting at the end. The fitting is a 3/16 inverted flare where the brake lines connect to. You do not need an extra fitting when you use the actuator.…

view full answer...

Answer 4

We have a wide variety of brake line kits that may work on your 1989/1990 EZ Loader Boat Trailer but the correct kit will be dependent on the length of your specific trailer. For example if your trailer is around 15' we have the HydraStar…

view full answer...

Answer 5

Your trailer must have free backing brakes if you have never used the surge brake actuating coupler reverse lockout. If you did not have free backing brakes, your brakes would most likely brake even if they didn't lock up when you back up because…

view full answer...

Answer 6

Your Dico brake assemblies are 10 inch by 2-1/4 inch so the part #T4423400 and #T4423500 would both work as replacements. There is quite a bit of overlap between Titan and Dico parts.

view full answer...

Answer 7

The best way to identify the seal needed, is to get the number that is stamped or imprinted on the seal. You may have to remove the seal in order to see the numbers. If you cannot find the number on the seal, if you can find the numbers on the inner…

view full answer...

Answer 8

The difference, other than cost, between the Titan Uni-Servo free backing Hydraulic 10 inch Trailer Brake Assemblies, #T4423400, and #T4071500, is that the #T4423400 assembly has Galphorite plating which delivers superior corrosion protection for…

view full answer...

Answer 9

Though you can definitely go with the all flexible line kits, like the Kodiak Hydraulic Brake Line Kit #15SI-BLKIT, I do prefer the more traditional steel kits, like the HydraStar Hydraulic Brake Line Kit #HS496-251. I have found the steel line to be…

view full answer...

Answer 10

We do have what you need to replace the UFP HD-1377-10 hub and drum as well as add hydraulic brakes for your boat trailer. Here are the exact parts you will need: - Dexter Trailer Hub and Drum Assembly #84546UC3 - Hydraulic Trailer Brake Kit -…

view full answer...

Answer 11

The Dico 15638 is a 10 x 2-1/4 inch brake drum/hub that used kind of an oddball bearing setup, inner bearing LM67048 and 3/4 outer bearing LM11949. None of the hub/drums we currently carry are compatible with this bearing set. If the drums are still…

view full answer...

Answer 12

Sounds like you have standard 10 inch brake assemblies on your trailer. The part #AKEBRK-35L would work for the left hand side and part #AKEBRK-35R would work for the right hand side. These are both the same size as what you have and have the same 4…

view full answer...

Most Common Trailer Brake Line Fitting Size

Product Page this Question was Asked From

Continue Researching