What Size Staples are Recommended for Installing Bunk Board Carpet on Boat Trailer

Question

Question:

Hello, staple gauge and length for new carpet installation- using air gun. THANKS

asked by: W C

0

Expert Reply:

We typically try to use 1/2 inch stainless steel staples when we install the CE Smith Deluxe Marine-Grade Carpeting, # CE11330, but 3/8 inch staples will work too. I would not go much shorter than the 3/8 inch staples because you don't want them to work their way out over time. I strongly recommend using stainless steel staples if possible. They will last much longer because they provide the best rust resistance.

I would also recommend uses a hammer to drive the staples all the way into the boards. Especially in areas were there may be extra layers of carpet.

expert reply by: Jameson C

0

Answer 1

I've never had any bleed through that damaged the hulls of my PWC's but for pontoons (presumably stainless) there is some concern. The CCA used to pressure treat wood several years ago was very corrosive to stainless steel, from what I read…

view full answer...

Answer 2

As long as the seal in the bearing kit part #BK1-150 is flush with the hub it is okay to have a small gap between the seal and inner bearing. When installing the seal you only insert it enough so that it is flush with the hub. The seal's job is…

view full answer...

Answer 3

Depending on how the trailer was made, there will be a few spots you can check to identify the axle. First, if the trailer was pre-made by a specific company, you may be able to find this information in either the paperwork or on a placard somewhere…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 7

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 8

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 9

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 10

I currently have three diffrent self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes which are attached for you below. eTrailer Electric Trailer Brake Kit part #AKEBRK-35-SA (3,500 Axles) Dexter…

view full answer...

Answer 11

The BTR and BT8 denotations refer to the spindle, not the trailer hub. The difference between a BTR and BT8 spindle is that the BTR spindle uses a 1.063" diameter L44649 bearing and the BT8 spindle uses a 0.99" diameter L44643 bearing. In…

view full answer...

Answer 12

After you've packed the bearings and assembled everything, carefully slide the hub assembly onto the spindle and install the outer bearing. Install the spindle and tang washer and run the spindle nut down finger tight, then rotate the hub back…

view full answer...

What Size Staples are Recommended for Installing Bunk Board Carpet on Boat Trailer

Product Page this Question was Asked From

Continue Researching