What Size Hole is Needed to Install Sealed Uni-Lite Mini LED Side Marker/Clearance Light # MCL12AKB

Question

Question:

What size hole to I need to drill for part mcl 12akb ???

asked by: Adam B

1

Helpful Expert Reply:

Installation of Sealed, Uni-Lite Mini LED Side Marker and Clearance Light # MCL12AKB requires a 3/4" hole at desired location. I have linked a video showing an example installation for you.

expert reply by: Michael H

1

Answer 1

Hey Jacob, the ApexAnchor tie downs part number #TL38SV and #TL26SV work perfectly fine with running boards so you would not need to remove them.

view full answer...

Answer 2

Hey John, the ApexAnchor tie downs part #TL38SV and #TL26SV would not negatively affect your truck bed usability since when not in use they will sit totally flush. You can use them as anchor points too like you asked about. Each of the anchor points…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

Yes, it does. The TorkLift Custom Fit Tie Down Kit Item #TL46VV does indeed include the Front item #TLD2101 and Rear item #TLD3109. These will fit your 2006 Dodge Ram 2500 so long as you do not have running boards that run past your cab. If you do…

view full answer...

Answer 5

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

The Torklift Tie Dowdn part #TLD3109 that you referenced is the correct rear tie down for your 2008 Dodge Ram 3500 Diesel 8 foot box with factory installed hitch. The matching front tie down is the part #TLD2101.

view full answer...

Answer 8

For your 2008 Dodge Ram 3500 long bed with a Torklift Hitch part #TLD1102-30 the correct set of Torklift Camper Tie Downs are the #TLD2101 for the front and the part #TLR3503 for the rear. I attached an install video for these for you to check out as…

view full answer...

Answer 9

I took a look at the online copy of the owner's manual for a 2018 Toyota RAV4 and it did not list a maximum tongue weight capacity. The tongue weight is meant to be around 10 percent to 15 percent when towing a trailer, like you said, but our…

view full answer...

Answer 10

As far as mounting your Honda Grom and your scooter to your 2019 Winnebago 22R motorhome, we unfortunately do not have a traditional bike rack that will work for the weight of those bikes. However, the best route is to use the Ultra-Fab Dirt Bike…

view full answer...

Answer 11

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

What Size Hole is Needed to Install Sealed Uni-Lite Mini LED Side Marker/Clearance Light # MCL12AKB

Featured Help Information

Miscellaneous Media

Continue Researching