What our customers are saying:
I received this order yesterday. Thanks for the outstanding service. I appreciate it! Thanks, Alex
Alex
Blowing Rock, NC
Videos
for Tailgate Locks
Help Articles
Expert Answers
Yes, the Pop & Lock Power Lock Conversion Kit for Truck Caps and Hard Tonneau Covers part #PAL9772 or part #PAL9555 will work on the Leer 100XQ Truck Caps because it uses a cable latching mechanism and the handle is not riveted on.
I checked with Pop & Lock for you and there is a system that they have confirmed will work with 2011 and newer Leer 100XL, Leer 100XQ, and Leer 700: - Pop & Lock Power Lock Conversion Kit for Truck Caps and Hard Tonneau…
The Leer 100XR isn't specifically listed by Pop and Lock but more than likely the #PAL9772 will fit. It requires a frameless, bonded glass door with a 1-1/8" center hole for a rotary latch. This particular kit would upgrade…
The Pop & Lock Power Lock Conversion Kit for Truck Caps and Hard Tonneau Covers #PAL9772 will work on the A.R.E. MX series truck cap you referenced on your 2017 Ford F-250 Crew Cab Short Bed. This will give you a clean look along with…
Pop and Lock does have the manual locking tailgate handle, #PAL5500, that will work with your 2015 Toyota Tacoma with backup camera. You can turn it into a power locking handle by adding conversion kit #PAL8525.
I do have an option for you to get the locks working again but we don't carry Load Lock so I don't have any advice or replacement parts for this. That said, you should be able to pretty easily replace this with the Pop & Lock…
I can certainly point you in the right direction. The Dometic Duo Therm 3107541.009 is a model that we see fairly frequently. Now I do not have literature on your specific camper that will tell me if it is ducted or ductless, but the Advent units…
The Bauer Products T-Handle Lock for Truck Caps #BA57VR comes with a J-327 key. So by ordering 3 of these they are all keyed alike. This particular handle is for locks rotating counterclockwise. We also have the Clockwise T-Handle #BA84VR if your…
I would use a protractor, see photo, place the protractor on the edge of the inside of one side of the trailer frame and the other inside edge of the trailer frame should be parallel with the 50 degree line on the protractor. Another way to verify…
Most A-Frame Trailer Couplers have a standard of 50 degrees. I produced a short video for you showing the angle of the etrailer A-Frame Coupler, part #CA5400. I have also linked an FAQ on trailer couplers.
Unfortunately, Atwood no longer has the repair kits available. They were bought out and the company that now owns them stopped producing the repair parts you need. I recommend the A-Frame Trailer Coupler - Yoke Latch #CA-5210-B for your replacement…
The standard a-frame coupler degree is 50 degrees but we do have a 32 degree coupler with the part #DM15633-81 but the rear width of it is 9-7/16 inches.
Search For Custom Fit AccessoriesSelect A Category Below
Towing
Trailer Hitch
Trailer Wiring
Brake Controller
Base Plate for Tow Bar
Vehicle Tow Bar Brake System
Vehicle Tow Bar Wiring
BOLT brand vehicle and hitch locks
Cargo Control
Roof Rack
Trunk Bike Rack
Performance Accessories
Air Filter
Exhaust
Transmission Cooler
Performance Chip Tuners
Vehicle Lights
Tire Chains
Fluid Filters
Vehicle Engine Heaters
Radiator Fan
Cabin Air Filter
Lift Assist
Vehicle Trim
Floor Mats
Trim Kits
Vehicle Covers
Bug Shield
Side Window Vents
Vehicle Seat Covers
Replacement Mirrors
Windshield Wiper Blades
Windshield Covers
Vehicle Air Mattress