Roadmaster 6-Diode Universal Wiring Kit for Towed Vehicles with Separate Lighting
Item # 154-792-118158
Our Price: $189.93
Confirmed to Fit
2008 Toyota Tundra
Will this fit?
To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
This item qualifies for Free Shipping
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
- All Info
- Reviews (55)
- Q & A (0)
- Photos
2008 Toyota Tundra - Roadmaster 6-Diode Universal Wiring Kit for Towed Vehicles with Separate Lighting
- Diode Kit
- Splices into Vehicle Wiring
- Tail Light Mount
- Universal
- Roadmaster
Connect your towed car's lighting system to your RV's to get the brake lights and turn signals required for towing. Designed for use with Toyota Tundras that have separate brake and turn signals. 4-Pole flat loop and wiring converter included.
Features:
- Connects your RV's tail, brake and turn signal lights to your towed vehicle's lighting system
- Designed for use on towed vehicles that have a 3-wire system (separate brake and turn signals)
- Prevents electrical feedback and the damage it can cause to your towed car's electrical components
- Includes tail light converter to adapt your RV's 2-wire system (combined brake and turn signals) to work with the towed car's 3-wire system
- Contains everything you need to wire your car for flat towing
- 6 Hy-Power diodes
- Tail light converter
- 30' Long strand of 4-wire electrical cord
- 6' Long cord with 4-way flat connectors - both vehicle and RV ends
- Ring terminal and wire connectors
- 3' Long split-wire loom
- Limited Lifetime Warranty
Specs:
- Max amperage: 85 amps
- Max voltage: 24 V
Note: If your RV has separate brake and turn signal lights, you do not need to install the included tail light converter. However, you will need to replace the 4-way vehicle-side connector with one that is capable of carrying the separate signals.
The diagram below shows the installation of the 6-diode tail light wiring kit on a towed vehicle (or dinghy) that has separate turn signals (typically amber) and red brake lights. This kit will most often be used with a motor home that operates off of a 2-wire system wherein the brake lights do the flashing for the turn signals. The included tail light converter (118158) is used to convert the combined brake and turn signal lights to separate ones to match those of your towed vehicle.
154 and 792 Roadmaster Universal Wiring Kit with 6 Hy-Power Diodes and 118158 Tow Ready Tail Light Converter
Installation Details
Customer Satisfaction Score:
87% were satisfied with this product
13% of customers were not satisfied
- etrailer mistake
- Wrong item was ordered
- Received too many
Customer Reviews
Roadmaster 6-Diode Universal Wiring Kit for Towed Vehicles with Separate Lighting - 154-792-118158
Average Customer Rating: 4.8 out of 5 stars (55 Customer Reviews)
Connect your towed car's lighting system to your RV's to get the brake lights and turn signals required for towing. Designed for use with vehicles that have separate brake and turn signals. 4-Pole flat loop and wiring converter included.by: Chris B03/25/2015
Subaru Outback Wagon
In ordering the parts I got a little confused as to exactly which kit I needed. My motorhome has combined brake/turn signal lights & the car ('03 Subaru Outback) has separate brake/turn/parking lights. Thought I needed the 6 diode kit (which I ordered) until I had all the parts here & read through the instructions for the umpteenth time (BEFORE cutting anything) & then realized what they were doing. Turns out all I needed was the 4 diode kit. Sounds like there won't be any problems returning the unneeded parts since they were never installed. Great service there!
Took a lot apart in the back of the car because of the lack of space behind the tail light assemblies, but it all comes apart pretty easily. Also allowed me to route the wiring along side the stock harness. Have a bunch of 1/2" split loom here & used it.
Thought I would have lots of wire left over, but I actually had to splice 2 cut offs to make a jumper long enough to get from 1 side of the car to the other. Glad the car wasn't any longer & I didn't have to make up 2 jumpers as with some of the kits!
Hardest part was finding a hole in the firewall & getting the harness routed under the dash so as to not tangle with the pedals, etc. I just don't flex like I used to.
Everything works fine although it was NOT a "5 minute job".
by: Rich L.03/05/2013
Chevrolet Volt
The diodes and wiring are good and worked well. But the 118158 converter produced a 3.5 volt drop such that the brake lights were as dim as the tail lights. And when a turn signal was triggered the brake lights dimmed even further. I ended up stringing a separate brake wire through the car and re-wiring my truck with a 5-wire connector.
by: Jerry B.08/04/2013
2013 Honda CR-V
Prompt deliver of product. We haven't gotten this part of our project installed, we are still watching YouTube videos and other info on procedure. Had very little difficulties installing base plate on our 2013 CRV this should go well also. Our lights are a little more complicated but once we figure out how to actually wire to them every thing we've learned so far is very straight forward.
by: Dale H06/26/2020
2013 Honda Fit
An ingenious system that enables a combined break and turn signal set up on your RV to properly operate the separate turn signal / brake setup of your toad. Beautiful!
Dale H.
6/28/2021
Have been using the brake and turn signal system for over a year now, and it is still working flawlessly!!
by: Christopher03/14/2018
2012 Ford Five Hundred
I used this wiring kit on a 2012 Fiat 500 Sport. All of the components worked as advertised and I am really pleased with the result. I used the 6 diode kit so the FIAT's turn signals would work the same when it's being towed as when it is driven.
This was my first light wiring kit installation and it was quite a challenge on the small FIAT to fish the flat cable from the rear of the car to the front. I ran it along the drivers side - over the rear wheel well, along the rocker panel, and up over the front wheel well. The wheel wells were the most difficult part of the job. Running the cable from driver's side to passenger side along the rear bumper and running it from the front wheel well to the front of the car and installing a connector were straightforward.
One problem I ran into is the female disconnect terminals supplied with the kit that are used to connect wires to the diodes anticipated a thicker wire (16-14 AWG) than what the FIAT uses. A quick trip to a close by big box store was all that was needed to find the same connectors for a thinner gauge wire (22-18 AWG). You still use the supplied disconnect terminals with the flat cable connections to the diodes.
by: John J06/12/2016
Honda
I bought this wiring kit because I wanted to wire my 2013 Honda CRV myself. E-Trailer has a video that is helpful in its installation . What I later found out was you need to route the wires through some covers underneath the vehicle and unless you have some means to raise the vehicle pretty high that routing will be difficult. I went to the Honda dealer and several other auto places and no one would install this kit for me because of liability reasons so now I have a product of question. I ended up at a friends garage who had a lift and we routed the wire from side to side and from front to back in about 20 minutes. Once secured in place I took the car home to finish the diode installation. Using the video it was easy to install. The only problem I had was putting the rear tai lights back in. You will need the separate the diodes as the space between the body and light housing is very close. Other than that everything worked out well.
by: ALEX A11/08/2016
The wiring works great, I got more in the KIT than I could possible use and I am sure I had to pay for the extras, but I got what I needed and am very happy.
Alex A.
11/8/2017
it is doing great
by: David10/28/2017
2010 Suzuki Grand Vitara
A great product. Installed easily. Previous wiring experience would be good for somebody wanting to use this.
It has performed flawlessly over the past year. I’d recommend it.
David
10/28/2018
Fantastic. No problems at all. Works as required every time I plug in.
by: Bill02/05/2018
Toyota Tacoma
I used the wiring harness on my Tacoma pickup in preparing to tow it behind our 40’ motorhome. The harness went on easily from the front grill to the rear lights, where I soldered and heat wrapped each connection. The instructions were ample and easy to follow.
It’s been a year since the installation, and the wiring has worked flawlessly!
by: Jean C07/24/2019
Honda Civic
The Roadmaster Wiring Harness was installed easily by our mechanic and works perfectly with our Civic and RV. I'm certain we will use etrailer.com for our new dinghy towing requirements!
by: Ron B05/23/2017
2015 Fiat 500
The kit contained all you need to wire lights on a Fiat. The instructions were clear and concise. Excellent product and service as usual for etrailer.
Ron B.
5/25/2018
After one year this kit is still doing its job flawlessly.
by: Jerry07/29/2021
Ford Ranger
Install on a 2020 Ford Ranger. The product was excellent. The only problem I had was trying to remove the nuts holding the front bumper on. Ford has these bolts embedded in a hard plastic frame that spaces the three bolts on each side. In trying to remove the nuts I got them started then they would neither come on off nor reinstall. The nuts were spinning the bolts. After thinking about the fix I was in I decided to cut the factory bolts off and replace them with 1/2" x 1 1/2" bolts with fender washers. I tried a sawsall with a metal cutting blade and the bolts ate the teeth right off. I put on a Milwaukee thick metal cutting carbide tooth blade and that did the trick. Other than that, which is Ford's fault, everything went as the etrailer videos showed. If you are doing this make sure to spray the exposed bolt threads with WD-40 or something like before you try to remove the nuts.
by: Rich B.06/02/2012
2012 Kia Sportage
This harness was an excellent choice. It took about an hour and fifteen minutes to install. Everything is spelled out for you in the instructions and if all else fails, watch the online video. The hardest thing was removing the tail light on the Sportage. I has a ball joint connection that forces you to pull harder than you think you should. I was afraid I would break the light. But it popped out and the rest was easy. Very complete and works great! The connections fit like factory. Very Pleased.
by: Dale05/06/2016
This is my second purchase of wiring kit for towed vehicle I have bought from Etrailer. I had some questions and Etrailer was able to answer every question I had. I will go back to Etrailer next time I need products such as this.
by: Danny07/05/2014
2013 Chevrolet Sonic
I found the product to be of very high guality. I did not supply pictures as I would need to remove my taillights again. I had to covert a motor home that did not have separate turn signals to a Sonic that did. The materials supplied allowed me to just that. I do have two other comments-The instructions showed the wires on the car on the passenger side which is opposite from the Sonic and most others I would think. I had to reverse my thinking to do the correct procedure. Also, could you not supply unit specific instructions if the towing vehicle lighting arrangement and the towed vehicle was identified. This would eliminate the extra parts that I did not need and help the customer complete the task. Other than that, very good product. I guess it is better to have extra parts ratter than not having enough but I just thought this might cut the cost for some applications.
by: John D07/29/2021
Was skeptical about using with led tail lights,but it all went well. The installation videos are spot on. After one year and about 12k miles traveled, no problems. My vehicle is a 2020 Ford Ranger.
by: Wayne06/06/2015
Product arrived on time.Online videos very well done.Katie D. provided excellent customer service on all the parts ordered.
Wayne S.
6/11/2016
very happy with product still working without any problems
by: James04/17/2021
Works as advertised. Design of these wiring kits is based on converting the common 3 bulb brake/turn signal systems to a 2 bulb system. This makes them unnecessarily complicated.
by: only1jerry11/05/2016
2005 Subaru Forester
I did a lot of research before buying. etrailer's prices and support are above average. I ordered the Roadmaster 913-1 baseplate, Falcon-2 towbar and 154 universal lighting kit. I was completely surprised by the fast shipping, all parts arrived 3 days before I expected AND the shipping was free!
Before I ordered I talked with etrailer support to ensure I ordered the correct parts. They were knowledgeable and helpful.
by: Dave G.07/28/2015
2008 Honda Fit
Very complete, hi quality, reasonably priced kit for lighting my "toad". If you have combined lights on your RV and separate lights (brake and turn) on your "toad", this is the kit.
by: Mike03/29/2017
Nice set up. Instructions were spot on. The hardest part of the installation was removing car interior panels to get to the wiring. Would definitely recommend this product.
by: Dale P03/20/2019
Ford
I ordered a towbar and accessories through the Internet site. It was very easy and also very informative. The supplies were ordered and I receive them in a couple of days. It was a great price and I did much research before I ordered. We are planning to install the towbar on our Ford C-Max and tow it with our phoenix cruiser 3100.
by: Denny K.07/14/2016
2014 Fiat 500
a little bit hard to get all wiring in, because I want the wiring not to be apparent and not exposed to harsh weather( snow, salt ,etc). But this setup is ideal, works perfectly and very quick when you connect your car the the motorhome.
by: Kevin 04/27/2021
Contained everything I required except the independent stop light switch.
by: Greg R.12/18/2016
Customer service was the best. Product delivered as expected. I recommend this wiring package. My towing safety comes first and Etrailer delivered.
25
55
Show More Reviews
See what our Experts say about this Roadmaster Tow Bar Wiring
- Can Bulb and Socket Flat Tow Wiring Fit a 1999 Jeep Cherokee SportThe Roadmaster Tail Light Wiring Kit for Towed Vehicles # RM-152-LED requires a 1" hole to install the bulbs into the tail light housing. It does look like you're limited on spacing inside your housing and when I reached out to my contact at Roadmaster he confirmed that we need to go with a different tail light kit for your setup. I recommend the Universal Hy-Power Diode Wiring Kit # RM-154 if the brake and turn signal are combined on your 1999 Jeep Cherokee Sport, or the Universal Wiring...
view full answer...
- Troubleshooting Wiring Ground Connection From Towing Vehicle to Towed Vehicle InstallationThe Roadmaster 6-Diode Universal Wiring Kit for Towed Vehicles with Separate Lighting # 154-792-118158 does need to be grounded to the vehicle chassis at both locations. Without a solid metal to metal ground, the converter and the trailer wiring may not function properly. It is possible they could work being tied together and connected into the towing vehicle ground through the 4-way wiring harness, but that is putting a lot of faith in your tow vehicle ground connection and the gauge...
view full answer...
- Recommendations for Using a Roadmaster Sterling Tow Bar on a 2001 Honda CR-VI would like to caution you that you will want to make sure that all the components of the Roadmaster Sterling tow bar system are present. Other customers have mentioned that there are various pieces missing or forgotten especially when buying used tow bars. To flat tow your 2001 Honda CR-V behind your motor home you will need the following components: Tow Bar (your used Sterling is an excellent choice) Towed Vehicle Base Plates (compatible with your 2001 Honda CR-V, and your Sterling...
view full answer... - 2 Wire to 3 Wire Tow Vehicle Taillight Adapter for 2006 Chevrolet ColoradoYou definitely can use the 4 diodes you purchased, # 48955, to wire your 2006 Chevrolet Colorado to be towed behind your Motorhome. Along with the connector you purchased and the diodes you will need an appropriate length of Bonded 4 Wire, # 16-4B-1. I would recommend about 30 feet. When wiring the taillights your brake and turn signal will use the same filament in the brake light bulb with a 4 diode kit. I have added a wiring diagram for you to make the process easier. To eliminate running...
view full answer...
- Using a Roadmaster Falcon 5250 Tow Bar to Flat Tow a 2010 Honda CR-VBefore you tow the vehicle you will want to consult the owners manual for information on towing the vehicle. For the 2010 Honda CR-V, you will need to use Roadmaster base plates, # RM-521559-4, that you referenced. Base plates are vehicle specific so the # 199-5 base plates will not fit the 2010 Honda CR-V. You can use the Roadmaster Falcon 5250 tow bar with base plates # RM-521559-4. You can also use the Brake Buddy. In addition to the base plates, braking system, safety cables, and tow...
view full answer... - Wiring Harness Needed to Tow 1999 Mazda Miata Behind RVIn order to connect the lighting system on your 1999 Mazda Miata to your RV's and get the brake lights and turn signals required for towing, you will need Roadmaster 6-Diode Universal Wiring Kit for Towed Vehicles, # 154-792-118158. I have attached an article that covers the five basic components required to flat tow. Before getting the Miata set-up, I do recommend checking your owner's manual for flat towing compatibility and any restrictions or special instructions that they may have. The...
view full answer... - Tow Bar Lighting Recommendation for a 2007 Honda AccordI wish we had tow bar wiring that was plug and play for your 2007 Honda Accord, but the best option I can make for your vehicle that won't require any splicing would be a magnetic kit like the part # C6304, or your other option would be a diode kit that would require quite a bit of splicing like the part # 154-792-118158. I attached a couple help articles on tow bar lighting for you to check out as well.
view full answer... - Parts Needed to Flat Tow a 2014 Subaru Outback Behind a Motor HomeThe Roadmaster XL base plates # 920-1 are a fit for your 2014 Subaru Outback Wagon and the Stowmaster tow bar # RM-501. The Tow bar does fold up and store on the tow vehicle. There are no speed restrictions when the tow bar is folded up but it wouldn't take much just to remove the tow bar to avoid any unforeseen issues. The fasteners on your Outback appear to be push-in fasteners. There is a special tool you can use to make removing them easy, # PT73HJ. You will also need safety cables,...
view full answer... - Parts Needed to Flat Tow a 2006 GMC Envoy Denali Behind an RV with EazAligner 2000 Tow BarFor your 2006 GMC Envoy Denali you will need base plates # 3109-1. To attach your EazAligner 2000 tow bar you will need adapter # RM-038 and quick disconnects # RM-201. If you do not already have safety cables you will need to add some, # RM-643. The coiled design helps keep the cables off of the ground. For lighting you can use a simple magnetic kit such as # RM-2120. Or, for a more permanent solution I recommend the 6 diode kit # 154-792-118158. And finally, most states now require...
view full answer... - 7-Way to 4-Way Round Wiring Adapter to Flat Tow a 2001 Honda CR-VWe do indeed carry a 7-Way blade style to 4-Way round adapter. It is # HM47043. This is a coiled cable that can stretch to 8 feet long. The 7-Way end plugs into the RV and the 4-Way end to the vehicle. The diode kit you mentioned is # 154-792-118158. For a 4-Way receptacle to mount on the front of the CR-V use # PK11410. It looks like you will have to pull fuses to flat tow the CR-V. Consult the owners manual to confirm. To avoid having to pull a fuse every time you can install a fuse...
view full answer... - Flat Towing Wiring Harness for 2010 Chrysler Town and Country LimitedThe options for wiring/lighting kits for towing the van behind your Beaver motor coach can be seen by clicking on the link provided. The Beaver website does not include wiring diagrams for its Class A, B, C or 5th wheel RVs but I was able to find a wiring diagram for the van by doing a Google search on the phrase '2010 Chrysler Tow and Country wiring diagram'. This may well also appear in your owner's manual. These choices include diode kits like the Roadmaster # 154-792-118158 and magnetic...
view full answer... - Recommended Tow Bar Wiring For 1999 Chevrolet Tracker Being Flat-Towed Behind MotorhomeThe tow bar wiring kit I recommend for your 1999 Tracker is the Roadmaster 6-Diode Universal Wiring Kit for Towed Vehicles with Separate Lighting, part # 154-792-118158. You will need to hard wire the kit to your vehicle lighting which may mean you have to remove the tail lights to get to the wiring on your Tracker. We do not offer a custom wiring kit for your vehicle. I have attached a couple drawings that show how the wiring needs to be run on your vehicle you can check out. If you...
view full answer...
- Wiring Recommendation for Flat Towing a 1982 Jeep CJ 7 LaredoGood news, I can help you with your wiring needs. First thing is to identify if your Jeep CJ-7 has separate or combined wiring. You will be able to tell this typically by if your taillight has an amber signal. I have linked a Help Article on wiring for your convenience. The 4-diode kit from Roadmaster # RM-152 will work for both combined and separate wiring, but if you have separate wiring you won't have function of the amber blinkers with this kit. If you prefer to still have function...
view full answer... - Parts Needed to Flat Tow a 2021 Ford BroncoWe can help you out with that! In order to flat tow your 2021 Ford Bronco behind your 2022 Newmar Class A motorhome you will need at least 5 main parts. Those parts are a base plate kit, tow bar, safety cables, tow bar wiring and a supplemental braking system. I have included each of those parts below, along with a brief description of their purpose. Base Plate Kit: This is a custom fit part that provides attachment points on your Bronco for the tow bar to use. - Roadmaster Direct-Connect...
view full answer... - Parts Needed to Flat Tow a 2015 Honda Fit Behind a Motor HomeBasically, the difference between EZ4 base plates # RM-521569-4 and EZ5 base plates # RM-521569-5 for the 2015 Honda Fit is the design of the draw bar arms. The EZ4 base plate arms have a wide flat front to attach to the Roadmaster tow bar crossbar. The EZ5 base plate arms have 2-prong ends that attach directly to the tow bar without the use of the crossbar. Both sets will work with the Falcon 2 tow bar # RM-520 but the EZ5 would be easier to use. The base plates include short safety...
view full answer... - Recommended Flat-Towing Parts Needed For 2014 Ford C-MaxAll of the base plate kits we carry are very dependable. Personally, I like the Demco tow bars the best because of their independant arms. The Demco base plate kit for your 2014 Ford C-Max is part # DM9518305. To pair up with the base plates use the Demco Commander # DM9511012. It also includes safety cables. The tow bar lighting I recommend is the Roadmaster, part # 154-792-118158. I have attached a link to an install video for this on a 2014 C-Max. For a supplemental brake system...
view full answer... - Installing Roadmaster 6-Diode Wiring Kit for Towed Vehicles on 2014 Ford TaurusBecause wiring colors aren't always consistent even among models produced during the same model year, we always recommend wiring by function, not by wiring color. You can use a voltmeter or a simple circuit tester like part # PTW2992. There should be close to 12 volts being delivered to the taillights. Activate the left turn signal and probe the wires until you find the circuit that makes the tester blink along with the turn signal. Do the same for the right turn, the brake light and the...
view full answer... - Tow Bar Wiring Recommendation for 2012 Kia Soul for Activating Amber Turn Signals/Red StoplightsWe have diode tow bar wiring kits that you can wire to your vehicle being flat towed that will allow the turn signals and the stoplights to activate at the same time as your tow vehicle. For your 2012 Kia Soul the kit you'd need is the part # 154-792-118158. This comes with everything needed to install the wiring and convert the normally combined trailer wiring circuits of your tow vehicle to operate the seperate circuits of your Kia Soul. I attached a diagram that shows how it installs...
view full answer...
- Dolly Towing Kia Soul w/ Hitch and Converter w/ Flat-4 Behind Combined RVDoes your tow dolly not have lighting already? Of the various flat towing lighting options available for your Soul (see provided link), a bulb and socket kit like # RM-155 or a magnetic mount lamp kit like # RM-2120 would be the easiest to install and use. Both these kits have the benefit of remaining completely independent of the vehicle wiring, and no diodes will be needed. Other options like the # 38955 or the # 154-792-118158 diode kit would require more extensive installation. The...
view full answer... - Can Roadmaster Diodes Be Purchased SeparatelyYes, the diodes of the Diode Kit part # 154-792-118158 are available separately. They are available individually in the part # RM-790. If you need 6 like what the # 154-792-118158 has you would need to order a quantity of 6.
view full answer... - Roadmaster Base Plate Compatibility with a 2013 Ford Explorer Sport with Twin Turbo Eco-BoostAccording to Roadmaster, the XL Base Plate Kit, # 4427-1A, will fit on your 2013 Ford Explorer Sport with the twin turbo eco-boost engine. If you are planning to flat tow your Ford Explorer, I would first recommend checking your owners manual for any restrictions or limitations on flat towing your vehicle. If you determine that you are able to flat tow your vehicle, you will need a few other items as well such as a tow bar, safety chains, tow bar wiring and a supplemental braking system....
view full answer... - Converter Needed When Towing Vehicle with Separate Wiring System Behind RV with Combined SystemIt sounds like you are needing to properly activate the signal lights on your Scion xA, which features a separate wiring system, while it is being pulled behind your Sprinter 3500 that has a combined system. The Curt Vehicle to Vehicle Tail Light Converter # C56196 that you referenced is indeed the correct part for this application. The converter is specifically designed to separate out the combined signals on your RV so that it works with the light functions on your Scion xA. To complete...
view full answer... - Recommended Equipment Need To Flat-Tow 2010 Honda FitI checked out the owner's manual for the 2010 Honda Fit and on page 238 it states that the vehicle can be towed with the proper tow bar and equipment. I will make some recommendations that will work for you. The base plates I recommend are part # BX2253. The tow bar I recommend is the Blue Ox Alpha, part # BX7380. This tow bar comes with safety cables. The tow bar wiring I recommend is the Roadmaster 6-Diode kit, part # 154-792-118158. You will also need a fuse bypass, part # RM76511....
view full answer... - Install Video for Installing Diode Tow Bar Wiring Kit that Uses 6 DiodesThere is a version of the diode style tow bar wiring that we offer that uses 6 diodes and will activate dedicated brake lights with the part # 154-792-118158 which I attached an install video for on a 2008 Honda Fit for you to check out.
view full answer...
Do you have a question about this Tow Bar Wiring?
Info for this part was:
Test Fit:
Joe V
Test Fit:
Nicholas E
Test Fit:
Randy B
Expert Research:
Jackie C
Expert Research:
Mike L
Expert Research:
Michael H
Expert Research:
Jameson C
Expert Research:
John H
Expert Research:
Adam R
Expert Research:
Jeffrey L
Video Edited:
Zack K
Video Edited:
Sue W
Written by:
Lindsey S
Updated by:
Adele M
Updated by:
Rachael H
Updated by:
Wilson B
Updated by:
Hannah L
Updated by:
Isabelle B
Video by:
Andrew L
Video by:
Alan C
Video by:
Chris R
Installed by:
Cole B
Installed by:
David F
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
Jerry B.
2/2/2015
So far, so good. Weve only towed the car one way from KS to Fl. Everything working great. Thinking about adding a receiver hitch but, will take it to the dealer as we sold our farm, and our tools and have the grandsons arent available to do the hard work.