# 1
Curt Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs
Longer stinger let me drop the tailgate on my Tacoma with trailer attached. Replaced a similar but shorter Curt hitch and both are very substantial and well made for the weight of my trailer.
With good information from the website it was easy to order a Curt 2" Trailer Hitch, the Upgraded Circuit Protected Tail Light Converter Hardwire Kit w/ 4-Pole Connector and Circuit Tester - 119178KIT, Curt Ball Mount for 2" Hitches (3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs - D-4), Curt Pin and Clip Hitch Receiver - C21500, Rubber Tube Cover for 2" Trailer Hitch Receivers - I-728,Review, and 2" hitch ball 40038. Parts were delivered earlier than the initial estimate. Self installation (on a sloped drive way) took just under 2 hour. The fit of parts was very good, instructions and on-line video's were very helpful. My Kia did not have the wire plug in option, but the splice connections in the wire kit were easy to install. Most of the parts are hidden from view when the ball mount is not used.
# 2
B&W Tow & Stow 2-Ball Mount - 2" Hitch - 7" Drop, 7-1/2" Rise - 10K - Black
Using this hitch on my Expedition and LandCruiser. A standard hitch caused my 12 ft utility trailer to not ride level when towed behind either truck. Since my trucks have different ride heights, the B&W hitch allows me to get the perfect drop for each truck. Trailer responds much better to road issues level as opposed to angled behind the truck. Additionally, its rating exceeds both of the trucks’ towing capabilities, so I have the hitch I need for the future as I have plans for a heavier trailer down the road. Quality and fitment of the hitch is excellent.
I own 2 of these now. 1 double & 1 triple ball. For me these are great and have towed multiple trailers many miles with ZERO issues. Because I tow many different trailers with different sized couplers and even the load/tongue weight from load to load can change how much my truck squats since I do not have air bags on my truck yet (coming soon), the B&W Tow & Stow makes it so easy to adjust the height to level any of my trailers. Honestly I do not use the stow feature partly because I am lazy and tow often but also by leaving this massive chunk of metal sticking out, it may protect my truck from being bumped from a non driver. Hint to B&W, for such a nice device I wish it came with a silencer to quiet some of the rattling although it is not bad. Tip for new users: (1) Grease the pins from time to time to make adjusting the height or switching ball size super easy especially in northern states with snow and salt covered roads. (2) Use a locking pin to secure this to your truck. They are heavy but without a locking pin they are easy to "walk away".
# 3
Convert-A-Ball Cushioned Multi-Hitch Clevis and Pintle Hook Combo w/ 3 Balls - 2" Hitches - 10K
No problems with the hitch- makes it easy to switch between trailers! I have no complaints!
Very good product and I would have given it a 5 star rating but there is one critical flaw that is quickly remedied. When using the pintle hitch, the pressure exerted on pin while pulling a load can cause the pin to turn, thereby popping out the keeper pin. This happened twice and it was a good thing that I had the hitch positioned so that the pintle pin was installed going down allowing gravity to hold the pin in place even when the keeper pin fell out. I have since changed out this style of keeper pin with a cinch pin that can spin 360 degrees inside the 2" tube and no pressure is exerted on it by the load being pulled. If I were designing this from new, I would make it so that the draw pin on the pintle had a square shoulder much like a carriage bolt so that it can't turn thereby eliminating pressure on the keeper pin. Other than that it is a great product.
# 4
Convert-A-Ball Ball Mount for 2" Hitches - 8-3/4" Rise - 10" Drop - 8,000 lbs
Works great. Needed the drop to tow a utility trailer at level.
As always etrailer has the best products, best information and customer service, plus fast shipping! Thank you again!
# 5
Curt Tri-Ball Mount - 3 Chrome Balls - 10,000 lbs
Excellent product! With the three different ball sizes, this tri-ball mount gives you a lot of flexibility. Gone are the days of having several different ball mounts to fit different tongues. High quality construction makes this an excellent investment.
definitely solid as a rock
# 6
Curt Class III Ball Mount with 2" Ball - 2" Drop - 7,500 lbs
I have two of these. My first I bought two years ago. I very highly recommend this Curt Class III Ballmount 2" Drop because of its price, durability and quality. I towed various class 3 loads with ease and confidence with this ballmount. It slides into the hitch and does its job without fail. It looks excellent after towing a load. etrailer's price is about as good as it gets and delivery is very speedy.
Easy install, took around 30 minutes by my self to install. Hardest part of install was torquing the bolts ! Installed 13322 Class III Hitch - Gm 1500/2500 Pickup and Curt Class III Ballmount -2ball-2 Drop
# 7
Curt Fusion Ball Mount for 2" Hitches - 2" Ball - 4" Drop - 7,500 lbs
All of the products I've have bought for my trailer project from etrailer have been great. My go-to place for anything trailer related!
Haven't set this up yet but quality feels good. User error on my part as this is not a ball I can replace but the flat bed I plan on buying for my motorcycle is a 2" so not a big deal and the price was a decent buy.
# 8
Convert-A-Ball Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop -14,000 lbs
Very useful for adding tie down points. Only reason for not giving 5 stars was the need to cut off the extra length and drill new holes farther up for the pins so the units fit better.
Been using this shock absorbing hitch for over a year now. The finish is still good, no rusting, and it has become my favorite hitch insert for heavy trailers
# 9
etrailer 2-3/4" Rise or 4" Drop Ball Mount Kit - 7,500 lbs
I purchased the etrailer.com 2-3/4 " Rise or 4" Drop Ball Mount Kit, Curt Trailer Hitch Receiver and Twist-in 7-Pole RV-Style Trailer Connector for my 2011 Chevy Silverado. Quick Delivery! All the necessary parts arrived in perfect condition. Directions were spot on and the instructional videos were great.
The drop ball mount is the perfect size for my Jeep. The versatile hitch balls are convenient. Thank you for putting together a great kit, providing excellent communication, and delivering it quickly.
# 10
Curt Towing Starter Kit for 2" Hitches - 2" Ball - 2" Rise, 4" Drop - 7.5K
Nice combination to go with my front hitch for the F150.
dodge journey 2014 etrailer service excellent the hitch don't fit perfect with the spare tire other ways is pretty good if you tele out the spare tire you going to have a hard time to put them back etrailer sevicio es excelente la pieza no se acopla perfecto con la rueda de repuesto del resto se monta perfecto . si se retira la rueda de repuesto es muy dificil de poner de vuelta en el compartimento
# 11
Draw-Tite Ball Mount for 2" Hitch - 5" Rise, 6" Drop - 9-1/2" Long - 12,000 lbs
I got this to Flat Tow my Jeep in the near future. I needed the 5" rise and now the tow bar is almost parallel to the ground. Although the etrailer.com site said this was an economy unit, I am very impressed with the look and feel of the unit. It handles up to 12,000lbs! Nothing economy about it except the very fair price!!! The pictures and video, along with the measurements helped ensure the fit would be perfect and it is! I got a 1" rise ball good for 6000lbs to make the tow bar perfectly parallel. Thanks etrailer I will always shop etrailer first when looking for this type of equipment.
I bought a new truck with twice the towing capacity of my SUV. I needed a 6" drop instead of my original 3" drop, so I bought one with a 12,000 capacity. Very nice.
# 12
Draw-Tite Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 9" Long - 7.5K
Sara R was helpful helping me find the right hitch for what I described as needing. I was excited to see the hitch pin in my order details even though I didn't order it. Sadly, the picture gave me a false impression. Overall, excellent customer service and product.
Working in the sand and grass of my driveway my wife and I installed our new etrailer receiver hitch. Great fit and finish! Went right on as described in the online guide. Hitch required a spacer washer on top back bolt attachment point. Taped it on so it would not move while lifting in place and it stayed right there! Used a car jack to raise up and hold the hitch into the underside of the trunk tighten the bolts and reattached the tail pipe done. Now we can pull our Sunfish Sailboat any where the car will go.
# 13
Brophy Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 13-1/4" Long - 10K
Slightly longer, so you can open your tailgate with a cargo trailer attached. Trailers with a tongue jack that is forward are problematic for tailgates...
I’m pleased with the product and how prompt the delivery was. However the packaging was insufficient and the packaging was torn open all over. Scuffing of the finish is a result and of little consequence due to the intended use. It’s a stinger w/ball for motorhome. May I suggest better packaging in the future
# 14
B&W Tow & Stow 2-Ball Mount - 2" Hitch - 5" Drop, 5-1/2" Rise - 10K - Black
I wish I would have bought one of these years ago. It would have saved me from buying 4 different height hitch receivers. I have a boat trailer that requires me to mount this hitch upside down to get about 2.5in of rise. On the flip side is my utility trailer that requires a 2 inch drop. The kicker is that when I load the truck down with gear and people or load the utility trailer up really heavy, this hitch allows me to kick the ball up or down a notch to keep the trailer level. Also if you ever rent heavy equipment most of the trailers they use will have 2 5/16 ball, so I just flip the ball and I'm in business. Build quality and finish is excellent. I don't keep the mount on all year long but with some judicious use of grease this thing hasn't shown any rust over the past year of use. I am currently using this on a stock GMC Sierra 1500 and I really could have gone with one size down on the hitch drop/rise, but I figured if I ever bought a 3/4 ton truck or a friend with one ever needed to borrow the hitch it would have enough drop to work with that application as well. As it stands the 5in drop isn't too long to cause clearance issues with a half ton GM truck. For those of you who are wondering about thieves making off with the ball mount - the design of the tow and stow is such that with all the pins removed and the hitch installed on the vehicle, it is not possible to rotate the ball mount off the receiver. Especially if you mount the receiver using the inner most mounting hole. All that is needed is a locking hitch pin and the whole setup is secure. I've attached a picture of the hitch installed on a 2015 GMC Sierra 1500 4x4 for reference.
I am so absolutely thrilled with my trailer hitch! etrailer made my purchase extremely easy. I have never bought a trailer hitch before, but I was able to pick the right size and the capability that I needed, based upon awesome product videos and reviews. Your company has exceeded my expectations of customer service and prompt product delivery. I applaud you and your team!
# 15
Draw-Tite Drawbar for 1-1/4" Hitches - 5/8" Rise, 1-1/4" Drop - 7" Long - 3.5K
Items packed well delivered on time. Doesn't get much better that that.
The service is great and so is the price. Box came damaged but if it installs as easy as the last one I bought from etrailer I will be very happy!
# 16
Curt Towing Starter Kit for 2" Hitches - 2" Ball - 3/4" Rise, 2" Drop - 7.5K
There were some UPS delivery issues, damaged in shipment. But, etrailer.com jumped right on sending out another shipment after it was apparent that UPS would not complete the delivery. The installation took longer, maybe 1-1/2 hours, because I did not have all my tools ready and I was working on the concrete floor in the dark to outside with a portable shop light. Everything fit well and it looks great. The 2" drop ball mount was the perfect height for my 2019 Toyota Highlander Hybrid. I love the look of the Curt black insert that makes the hitch looks like it belongs on the car, nothing embarrassing at all. Anything negative? Maybe. The flat plate was a little difficult to hook onto with the UHaul safety chains on a 5x8 trailer. That's hardly a negative, though, and I wouldn't have spent more on another brand choice because of this. Happy happy!
Great fit and finish on this kit. So nice to be able to tow things with my Forester now. I thought I had an issue but figured out it was user error pretty quick, but only after I contacted etrailer for help. I heard back within 30 minutes of emailing and by that time I figured out my blunder. They were extremely helpful and responsive and were set on fixing the problem I thought I had. I have used etrailer for several different purchases over the past couple years and every time I have been thrilled with the service and the quality of product.
# 17
Brophy Drawbar for 1-1/4" Hitches - 5-1/2" Rise, 6" Drop - 7-1/4" Long - 3.5K
I just purchased a new hideaway hitch system. But the hitch sits only 15 inches off the ground at best. And, my trailer coupling is 22-23 inches off ground. So l needed 7-8 inches of rise on the new 1.25 inch receiver system. Internet research took me to etrailer and the Brophy hitch. I got 5.5 inches with the Brophy hitch, the highest available for a 1.25 inch receiver I could find. The others are limited to 5 inches max. I added another 1.5 inches with your Curt shock absorbing hitch. Voila, with a combined 7 inches of rise and on level ground the trailer now rides perfectly level!!!! Both parts were very easy to connect. Delivery was speedy. Thank you for saving the day and my investment in an expensive new hideaway hitch!
Quality parts, but the extra rise with this and the Curt Rocker Ball still wasn’t enough to avoid scraping the top of my inclined road while towing my boat.
# 18
Curt Multipurpose Ball Mount with 2" Receiver for Bike Racks and Cargo Carriers - 7,500 lbs
I am using the hitch for a car dolly and a bike rack. The fit is a little loose for the bike rackmI'll see it really works when get on the road.
Quality is excellent. However, it did not work so I am not sure what to do with it. I thought I could use the top hitch for a Bike rack and pull a utility trailer with other toys. The trailer is too close to make a turn so good try but not able to use it. Thank you for asking. I did not open the box for a while because I was having the trailer worked on so assumed I waited too long to return.
# 19
Draw-Tite Ball Mount for 2" Hitches - 3" Rise, 4" Drop - 9-1/4" Long - 16K
Perfectly as described, Box was a heavy hitch and the box must have been damaged in shipping so it was a little delayed. You can't mess up a forged hitch it still is in excellent condition.
This simple ball mount will get the job done. It's a solid casting so it weighs a lot.
# 20
Curt Heavy Duty Forged Ball Mount with 2-5/16" Ball - 4" Drop - 15,000 lbs
Arrived sooner than expected. A very sturdy hitch with pin. I especially appreciate having the rounded edges where we frequently walk at the back of the SUV. 4" drop is correct to match my truck and trailer hitch height on my Subaru Ascent.
Everything ordered and received was exactly as described. Everything was received in excellent condition and really quickly. Thank you etrailer team for the excellent service!
What our customers are saying:
"Easy place to shop. Fast delivery and great products. Very happy with my purchase."