2009 Pontiac Vibe Trailer Hitch
2009 Pontiac Vibe Trailer Wiring
2009 Pontiac Vibe Brake Controller
2009 Pontiac Vibe Base Plate for Tow Bar
2009 Pontiac Vibe Vehicle Tow Bar Brake System
2009 Pontiac Vibe Vehicle Tow Bar Wiring
2009 Pontiac Vibe Roof Rack
2009 Pontiac Vibe Trunk Bike Rack
2009 Pontiac Vibe Air Filter
2009 Pontiac Vibe Performance Chip Tuners
2009 Pontiac Vibe Vehicle Lights
2009 Pontiac Vibe Tire Chains
2009 Pontiac Vibe Fluid Filters
2009 Pontiac Vibe Radiator Fan
2009 Pontiac Vibe Cabin Air Filter
2009 Pontiac Vibe Floor Mats
2009 Pontiac Vibe Vehicle Covers
2009 Pontiac Vibe Side Window Vents
2009 Pontiac Vibe Windshield Wiper Blades
2009 Pontiac Vibe Windshield Covers
2009 Pontiac Vibe Vehicle Air Mattress
Videos
for Pontiac Vibe Owners
Help Articles
Expert Answers
Yes, the Rhino-Rack clamps, #DK185, will fit a 2009 Toyota Matrix. This is only part of the roof rack though and is made to fit on a naked roof (no type of roof rack at all already on the vehicle). There are some options for the remainder of the roof…
The Curt Trailer Hitch Receiver part #C12228 comes with conical tooth washers which will install with the teeth facing the hitch.
You definitely want all of the hardware installed for hitch #C13272 or any hitch because how it attaches is part of how it gets its rating. It sounds like the problem you are having is a factory weld nut that is packed with grime and corrosion.…
The Curt trailer hitch receiver for your 1997 Mercury Sable is the Class II #C12232. If the rust can be sanded off and the hitch repainted, then it is likely still structurally sound. The best way to have them evaluated is to have a trailer shop…
The Draw-Tite Class I #24812 hitch attaches to nuts welded into the frame of the vehicle using M12 X 40mm bolts which have a 1.25 thread pitch. If the weld nuts in your frame are corroded or clogged up with road grime, before resorting to chasing…
To determine the correct wiring for your trailer you will need to use a circuit tester, item #PTW2993, and attach the wires from the connector by function only. The light wires should be as follows, red is the stop turn wire and the black is the…
You would need a tire with more weight capacity. Basically you need to take the total weight of the trailer when loaded and ready to tow and divide that number by the amount of tires the trailer has and that's the minimum tire weight capacity…
Yes, we can ship the Space Dock 2" Receiver Adapter for Torklift Palomino Landing Pad Bumper part #TLA7900 to you in Canada! However, the quoted shipping costs does not include all brokerage fees and duties. Taxes are not included and all prices…
Did you have a 4-pin connector that had 5 wires or was it a 5-pin connector? There is a big difference since you normally see a 5-pin connector on a boat trailer with the 5th pin used for an electric reverse lockout solenoid on a brake actuating…
Most ball mounts, like the Draw-Tite #2753 can be used in both a rise (upside down) and drop (standard) position. I'm not seeing any Curt ball mount with a part number 45836, but as I mentioned, most ball mounts are designed to be used either…
I am not exactly sure which particular ball mount this is in reference to but the one you came from, the Draw-Tite Ball Mount for 2" Hitches part #2753 can be inverted to increase rise up to 2-3/4". This is the case for most ball mounts as…
Your 4-pin/5-wire wiring harness is what is called a "wishbone" type which simply means that there are two separate running light wires, one brown and one pink. This allows a separate running light wire for each side of the trailer which…