Expert Review Video:
Tube Step Specs:
Features:
The curved ends on these affordably priced step bars give your vehicle a streamlined look. The non-slip step pads in these polished stainless steel, 3" diameter bars sit in recessed areas instead of cutouts to inhibit internal corrosion.
Installation Notes:
No drilling required for installation
Tube steps are installed by attaching mounting brackets with the existing body mount bolts
Tech Tip:
Step Bars will not fit ZR2 models.
More Information >Tube Step Specs:
Features:
Custom-fit, round nerf bars have wide, non-slip step pads that help you easily enter and exit your vehicle. Constructed of carbon steel with a black powder coat finish to resist chipping, peeling, and fading. Custom installation with mounting kit.
Installation Notes:
No drilling required for installation
More Information >Tube Step Specs:
Features:
The curved ends on these step bars give your vehicle a streamlined look. Made of rust-resistant powder coated steel, these 3" diameter round bars have recessed step areas that prevent internal corrosion. Non-slip step pads provide sure footing.
Installation Notes:
No drilling required for installation
Tube steps are installed by attaching mounting brackets with the existing body mount bolts
Tech Tip:
Step Bars will not fit ZR2 models.
More Information >Tube Step Specs:
Features:
The curved ends on these step bars give your vehicle a streamlined look. Made of rust-resistant chrome-plated steel, these 3" diameter round bars have recessed step areas that prevent internal corrosion. Non-slip step pads provide sure footing.
Installation Notes:
No drilling required for installation
Tube steps are installed by attaching mounting brackets with the existing body mount bolts
Tech Tip:
Step Bars will not fit ZR2 models.
More Information >Tube Step Specs:
Features:
Custom-fit, round nerf bars have wide, non-slip step pads that help you easily enter and exit your vehicle. Constructed of stainless steel with a polished finish that resists chipping, peeling, and fading. Custom installation with mounting kit.
Installation Notes:
No drilling required for installation
More Information >Tube Step Specs:
Features:
The curved ends on these affordably priced step bars give your vehicle a streamlined look. The non-slip step pads in these powder coated steel, 3" diameter bars sit in recessed areas instead of cutouts to inhibit internal corrosion.
Installation Notes:
No drilling required for installation
Tube steps are installed by attaching mounting brackets with the existing body mount bolts
Tech Tip:
Step Bars will not fit ZR2 models.
More Information >Videos
for Nerf Bars - Running Boards
Help Articles
for Nerf Bars - Running Boards
Expert Answers
for Nerf Bars - Running Boards
The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…
view full answer...The number you provided, "7753400" is a…
view full answer...For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…
view full answer...If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…
view full answer...The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the…
view full answer...It sounds like the 2022 Chevy Silverado 3500 you are getting has the short bed. In that case, yes, you definitely want the sliding 5th wheel hitch for clearance. The good news is you will not need to purchase the entire…
view full answer...Below is the general process for bleeding an electric over hydraulic brake actuator like #K71-650. Fill reservoir with NEW brake fluid. Never re-use brake fluid that has been salvaged or removed from another system. Remove the key from the…
view full answer...To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…
view full answer...Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the…
view full answer...A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…
view full answer...Hi Jeff; thanks for the question and sturdy is definitely a good word for the etrailer tonneau that fits your 2022 Ram 1500 with a 5-1/2 foot bed, the etrailer Hard Tonneau Cover #e35DR.…
view full answer...M12-1.5 and 1/2"-20 threads are not going to be interchangeable. The diameter of an M12 thread is only going to be…
view full answer...Filter Products (12)
Contact and Help
What our customers are saying:
In these days of customer "no service" I am usually disapointed when doing business with people I don't know. It was refreshing doing business with you. I'm impressed!
Randy
Watkinsville, GA