Availability Of Replacement Parts For Aries ActionTrac Motorized Running Boards AA3025179

Question

Question:

I am researching retractable running boards for my Gen2 dodge. I will customize the fit. I am looking at your product. If i use your product and need parts say new gear drive or hinge, is parts available separately?

asked by: Don T

0

Expert Reply:

Hello Don, thanks for reaching out. We really do not offer much along the lines of replacement parts for the Aries ActionTrac Motorized Running Boards # AA3025179. Right now, the only replacement part we have are the end caps part # AA27DQ. If you are needing internal or mechanical parts, your best bet would be to reach out directly to the manufacturer to see if they can provide those. Typically, those are not parts that need to be replaced though.

expert reply by: Jesse M

0

Aries ActionTrac Motorized Running Boards
(click to enlarge)

Don T.

1/6/2026

Where can i find the specifications for the length of the drop each application has.

Jesse M.

1/7/2026

@DonT Typically that will be stated on the part page. For example, for the Aries ActionTrac Motorized Running Boards # AA3025179 the step drops down approximately 8".

Answer 1

If you could figure out a way to mount the Aries ActionTrac Motorized Running Boards item #AA3025165 then the answer would be yes. They're only 69-9/16" long so they'll easily fit between your wheels. The issue is these are just the…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 4

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 5

Hey Ian, great to hear from you again! The differences between the MORryde CRE3000 #MR87ZR and AllTrek 4000 #MR89DR that fit a 33" wheelbase is the height between the hanger and equalizer bolts, and the amount of travel the suspension style will…

view full answer...

Answer 6

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

Hey Mark, the only real downside to an offset ball like the Gen-Y part #GY43XR is going to be that it costs more typically and it would take up more room when stored compared to a non-offset ball like the #C38CR. The handling and weight carrying…

view full answer...

Availability Of Replacement Parts For Aries ActionTrac Motorized Running Boards AA3025179

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching