Expert Review Video:
Separate wiring system - brake and turn signals are sent along separate wires. A converter is required unless the vehicle is equipped with a tow package plug. The tow package plug has already been converted.
Custom Fit Vehicle Wiring Specs:
Plug-In Location:
Features:
Replace the existing 7-way on your vehicle with this socket. Built-in magnet creates tight connection with EZ Connector trailer-end plug (sold separately). Face-to-face contacts mean no bent or broken terminals. O-ring on lid makes a watertight seal.
Installation Notes:
For vehicles with factory tow package; may require additional components or may be used as a replacement harness
This wiring is intended to be used with the 319-S7-07 trailer side plug, which is sold separately.
If your trailer has conventional 7-way wiring, this wiring harness is made compatible with an EZConnect Adapter, which is sold separately.
Tech Tip:
Some vehicles have factory connector that will not come apart for this product to plug into, so the connector ends have to be cut off and hardwired together.
More Information >Custom Fit Vehicle Wiring Specs:
Plug-In Location:
Features:
Upgrade the 7-way connection on your vehicle and trailer with this complete kit. Built-in magnets create tight connection. O-rings make a watertight seal. Face-to-face contacts mean no bent or broken terminals. Includes plug holder and dummy plug.
Installation Notes:
For vehicles with factory tow package; may require additional components or may be used as a replacement harness
Tech Tip:
Some vehicles have factory connector that will not come apart for this product to plug into, so the connector ends have to be cut off and hardwired together.
More Information >Custom Fit Vehicle Wiring Specs:
Plug-In Location:
Features:
Replace the existing 7-way on your vehicle with this socket. Built-in magnet creates tight connection with EZ Connector trailer-end plug (sold separately). Face-to-face contacts mean no bent or broken terminals.
Installation Notes:
For vehicles with factory tow package; may require additional components or may be used as a replacement harness
This wiring is intended to be used with the 319-R7-07 trailer side plug, which is sold separately.
If your trailer has conventional 7-way wiring, this wiring harness is made compatible with an EZConnect Adapter, which is sold separately.
Tech Tip:
Some vehicles have factory connector that will not come apart for this product to plug into, so the connector ends have to be cut off and hardwired together.
More Information >Videos
for Custom Fit Vehicle Wiring
Help Articles
for Custom Fit Vehicle Wiring
Expert Answers
for Custom Fit Vehicle Wiring
The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…
view full answer...A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…
view full answer...I&…
view full answer...If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…
view full answer...Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846.…
view full answer...I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and…
view full answer...I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for…
view full answer...While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the…
view full answer...If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…
view full answer...The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.
view full answer...To see all of the correct wheel and tire combos…
view full answer...The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures…
view full answer...