Vehicle Suspension Specs:
Features:
...Factory Overload Springs The lower factory overload springs on your truck are designed to help compensate for a large payload. When you are hauling a heavy load, your truck's standard leaf spri...
Installation Notes:
No drilling required for installation
Product designed for vehicles with factory leaf springs and a lower overload spring
More Information >Vehicle Suspension Specs:
Features:
...are hauling a heavy load Improve steering control and braking when you are hauling or towing Level your headlight beams Reduce tire wear Maintain even load distribution with air pressure, leveling off-center...
Installation Notes:
No drilling required for installation
Compatible with in-bed hitch
More Information >Vehicle Suspension Specs:
Features:
...to help compensate for a large payload. When you are hauling a heavy load, your truck's standard leaf springs can't always counteract the weight of it. As a result, if you hit a bump wh...
Installation Notes:
No drilling required for installation
Product designed for vehicles with factory leaf springs and a lower overload spring
More Information >Vehicle Suspension Specs:
Features:
...from twisting Compensate for windy conditions, wind turbulence from big rigs, and weight shifts while cornering Lift your truck when you are carrying a heavy load and prevent bottoming out Adjust...
Installation Notes:
No drilling required for installation
Product can be used for vehicles with or without factory top overload springs
Tech Tip:
For vehicles used in off-road rough conditions, SuperSprings recommends adding their Poly Pad mounting kit P5KT ), sold separately.
More Information >Vehicle Suspension Specs:
Features:
...for a large payload. When you are hauling a heavy load, your truck's standard leaf springs can't always counteract the weight of it. As a result, if you hit a bump when your suspension is fully...
Installation Notes:
No drilling required for installation
Product does not work with SuperSprings suspension kits
Product designed for vehicles with factory leaf springs and an upper overload spring
More Information >Vehicle Suspension Specs:
Features:
...Extra-heavy-duty coil springs replace your OEM coil springs for better suspension support Reduce front-end sag caused by heavy equipment and slide-in campers Help to lift your truck...
Installation Notes:
No drilling required for installation
More Information >Videos
for Vehicle Suspension
Help Articles
for Vehicle Suspension
Expert Answers
for Vehicle Suspension
For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the…
view full answer...Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram…
view full answer...If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…
view full answer...The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the…
view full answer...Hey Tarek, for your 2023 Ford Raptor I recommend checking out the Timbren Suspension Enhancement System #T75MR. This suspension enhancement system has a load leveling capacity of 3,000 lbs, will increase stability while reducing sag, and will…
view full answer...Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers…
view full answer...I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and…
view full answer...What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one…
view full answer...If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…
view full answer...It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that…
view full answer...Your trailer looks awesome! The Road armor equalizers #LC696740 and Equa-Flex Cushioned Equalizers #LC279687 are both pretty similar in performance even though the Road Armor has two dampers. The main difference is the size of the equalizers. The…
view full answer...From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some…
view full answer...Filter Products (12)
Contact and Help
What our customers are saying:
Very helpful/friendly Customer Service. Competitive Pricing. Shipping was Fast.
John
Mankato, MN