Truck Bed Slide Specs:
Features:
Slide-out truck bed tray lets you get gear without climbing or crawling. Steel-framed, laminated plywood deck extends smoothly - 100 percent of its length - on sealed bearings. Aluminum sides have built-in tie-down tracks. 2,200 Lbs capacity.
More Information >Truck Bed Slide Specs:
Features:
Slide-out truck bed tray lets you get gear without climbing or crawling. Steel-framed, laminated plywood deck extends smoothly - up to 75 percent of its length - on sealed bearings. Aluminum sides have built-in tie-down tracks. 1,500 Lbs capacity.
More Information >Videos
for Truck Bed Slide
Help Articles
for Truck Bed Slide
Expert Answers
for Truck Bed Slide
My contact at Yates Rubber advises that a nominal 8-inch keel roller does not measure exactly 8 inches; typically they are slightly smaller than the specified size, much the way a piece of 2 x 4 lumber is not exactly 2-inches by 4-inches. I took…
view full answer...The stop light switch that you will need to connect the red wire to on the Brake Control Plug-In Harness for Tekonsha part #20127 may be pre ran to a set of wires taped to the underside of the drivers side vehicle dash. If the wires are not present…
view full answer...That spindle looks pretty well destroyed so best option is going to be to replace the axle. You are going to need to measure your current axles in a few places to get the correct one as we…
view full answer...I looked up pictures of the taillights that are on the 3110 Featherlite trailers and for the LED version of them you would want the part #STL36RB and #STL37RB. It looks like the spare tire mounts for your trailer are something you would have to get…
view full answer...Hey Jeff, the WeatherTech ImpactLiner Custom Truck Bed Mat #WT99KF would get secured to your bed using the TechHold Retention Device (see image attached) which is just a adhesive ball and socket. Basically, one the ball end would get stuck to the…
view full answer...On single axle trailers typically you put the hanger spacing right at 1/4 of an inch shorter than the leaf spring length from eye to eye center. So if you were using the leaf spring part #e54SR that you referenced which measures 25-1/8 inches long…
view full answer...On a single axle trailer you will want to have a hanger spacing of around 22-3/4 inches when using the 23-1/8 inch long Double-Eye Spring #e59SR. This will allow that rear shackle to correctly lean away from the axle for proper suspension travel.
view full answer...For your AL-KO 7210 braking assembly, you can use the Hydraulic Brake Kit #AKFBBRK-7 as a replacement. These braking assemblies measure…
view full answer...The Truck Trolley Sliding Truck Bed Tray #TR87VR actually just installs using straps, which is why it has a 300 lb weight rating as opposed to 1,000 + lbs like we see with some of the sliding cargo trays that bolt to the truck bed. The installation…
view full answer...The caliper bracket you are looking for is the Replacement Mounting Bracket #KCMB12D which is compatible with the 5 bolt mounting flange you have as well as the 225 Kodiak Dacromet calipers you have as well. Then for a bolt kit…
view full answer...The typical tire should run about 158 degrees (Farenheidt) once you get going down the road, but this can vary greatly depending on the weight of the trailer, how fast…
view full answer...I am sorry Lippert did not include their instructions with your Lippert Trailair Air Ride 5th Wheel Pin Box #LC158778 but I have included a link to them on the Lippert website. I also linked an image of page 3 from those instructions which shows…
view full answer...Filter Products (4)
Contact and Help
What our customers are saying:
Thanks for the good experience. Minus the one part that got shipped later due to availability, the products arrived ahead of the anticipated date. Real to life 'Live Help' is great, hope you can manage to keep it up. If I have further needs, will contact you guys again.
Andrew
Minneapolis, MN