These brackets let you create a fold-out workbench or seat in your enclosed trailer. Telescoping legs let you adjust height of bench. Mount to X track and E track rails. Fold flat against wall when not in use. Requires (1) 24" wide board.Features: Brackets help create a workbench or seat in your enclosed trailer Installation requires (1) 24" wide board (not included) Pre-drilled holes allow you to secure board to brackets with screws (not included) Telescoping legs with adjustable feet let you adjust and fine-tune height of bench or seat Legs and brackets fold flat against wall for storage Easy installation - just snap spring-loaded fitting into E track or X track anchor points Brackets can be easily moved from one E track or X track slot to another Heavy-duty steel construction with corrosion-resistant zinc finish Specs: Quantity: 2 brackets Weight capacity: 600 lbs Adjustable height: 26" - 40" Bracket length: 24" Mounting hole diameter (each): 1/4" Weight (each): 11.1 lbs 1-Year limited warranty
Hook up, check tongue weight, and get on the road with fewer steps. This kit pairs a 5,000 lb electric trailer jack with a jack foot tongue weight scale, letting you lift your trailer and verify the load during the same hitching process.Many 2015 and newer Ford F-150 trucks equipped with a smart 7-way may limit the available current until the trailer is detected and other operating conditions are met. That managed circuit is not intended to power a high draw jack motor. This condition is commonly associated with Ford factory tow packages, including the Trailer Tow Package and Max Trailer Tow Package.
Hook up, check tongue weight, and get on the road with fewer steps. This kit pairs a 3,500 lb electric trailer jack with a jack foot tongue weight scale, letting you lift your trailer and verify the load during the same hitching process.Features to know about Check, Adjust, and Hitch Up When you're getting ready to tow, it's hard to know if your trailer's tongue weight is right just by looking at it. Lower your trailer onto the gauge while it's still on your jack, see where the weight stands, move your gear if needed, and check it again before you hitch up.
Use your drill to raise and lower your trailer, then check tongue weight before you tow. This kit pairs a 2,000 lb A-frame jack with a jack foot tongue weight scale so you can adjust cargo and verify the load during setup.Adjust Cargo Before You Tow: Check the reading, move cargo, and check again while the trailer is still supported by the jack. 14" Lift: Manual A-frame jack lifts trailer tongue weight through the hitching and unhitching process.
Hook up, check tongue weight, and get on the road with fewer steps. This kit pairs a 3,500 lb electric trailer jack with a jack foot tongue weight scale, letting you lift your trailer and verify the load during the same hitching process.Many 2015 and newer Ford F-150 trucks equipped with a smart 7-way may limit the available current until the trailer is detected and other operating conditions are met. That managed circuit is not intended to power a high draw jack motor. This condition is commonly associated with Ford factory tow packages, including the Trailer Tow Package and Max Trailer Tow Package.
Perfect for campers, RV travelers, and anyone using a trailer, these jacks make life easier and more enjoyable. They're designed with comfort and convenience in mind, helping you save time and energy for what matters most - your journey.Features: Effortless Operation: Electric jack makes lifting and lowering your A-frame trailer quick and effortless Quiet Powered Drive: Operates quietly, eliminating the need for hand cranking Simple Controls: Top mounted on/off and retract/extend buttons ensure straightforward operation Weatherproof Buttons: Covered with a flexible, rubber-like boot to keep water out and protect the inside of the housing Easy Installation: Bolt-on design means no hassle, no headaches Easy Drop Leg Adjustment: Extends up to 4-1/2&uqot; for extra lift by pulling the pin.
Perfect for campers, RV travelers, and trailer users, these jacks make adventures easier and more enjoyable. Designed for convenience and reliability, they save time and energy, so you can focus on what truly matters - your journey.Features: Effortless Operation: Electric jack makes lifting and lowering your A-frame trailer quick and effortless Quiet Powered Drive: Operates quietly, eliminating the need for hand cranking Simple Controls: Top mounted on/off and retract/extend buttons ensure straightforward operation Weatherproof Buttons: Covered with a flexible, rubber-like boot to keep water out and protect the inside of the housing Easy Installation: Bolt-on design means no hassle, no headaches Easy Drop Leg Adjustment: Extends up to 4-1/2&uqot; for extra lift by pulling the pin.
... Best for gooseneck setups where you can step between the truck and trailer. Heavy-duty jack screw can lift up to 5 tons.But, if you are just using it to stabilize or support a parked trailer, then you should focus on the jack's support capacity. Heavy-duty jacks like this one stabilize about 25% of your trailer's total weight when it's loaded up.
Black powder coated A-frame jack has a retracted height of 8-3/8" and an extended height of 24". The external gearbox is easily accessible, and the zinc-finished sidewind handle arm provides a sleek look.Features: Utility jack lets you raise and lower your A-frame trailer Sidewind handle has zinc finish for attractive look and rust resistance Black powder coat finish resists corrosion External gearbox is easily accessible Effortless greasing with built-in grease zerk Footplate or caster sold separately Specs: Bracket height (from bottom of inner tube to bottom of bracket): 8-3/8" Retracted 24" Extended Lift: 15-5/8" Clearance: 15" from bottom of bracket to top of jack Outer tube diameter: 2-1/4" Inner tube diameter: 2" Handle radius: 8" Lift capacity: 3,000 lbs Support capacity: 5,000 lbs 1-Year warranty
Weld-on, pipe-mount swivel jack pivots up for travel. Square design provides solid side-load support. Retracted height is 14-1/2". Extended height is 29-1/2". Drop leg adds 13-1/2" of manual adjustment to 15" of lift.Features: Utility jack lets you raise and lower your trailer Ideal for agricultural and commercial applications Tubular swivel design lets you twist jack up for storage, down for use Pull pin with clip holds jack in place Lanyard connects pin to jack so it won't get lost Square jack provides more side-load capacity than round-tube jacks Belly band welded to the outer tube provides extra strength Sidewind handle has zinc finish for attractive look and rust resistance Drop leg allows for increased lift and saves time when raising or lowering Black painted outer tube Zinc finished inner tube and footplate for corrosion resistance Welded-on footplate minimizes sinking in soft ground Effortless greasing with built-in grease zerk Weld-on installation with included female pipe mount Specs: Jack height (from bottom of foot to center of pipe mount): 14-1/2" Retracted 29-1/2" Extended Lift: 15" Drop leg adjustment: 13-1/2" Total adjustment: 28-1/2" Lift capacity: 7,000 lbs Support capacity: 8,000 lbs Outer tube width: 2-1/2" Inner tube width: 2-1/4" Footplate dimensions: 8" long x 6" wide Pipe mount diameter: Inner: 2" Outer: 2-1/2" Handle radius: 8-1/8" Adjustment hole spacing on drop leg: 3-3/8" from center of hole to center of hole 1-Year warranty
Square-tube jack is ideal for supporting heavy pontoon or bowrider trailers. Footplate is more stable than caster wheels. 15-3/8" of lift plus 13-3/4" of drop leg travel. Clear zinc finish resists rust.Usually, your tongue weight is about 10-15% of your gross trailer weight (GTW). For example, a 10,000-lb trailer has a tongue weight of 1,000 lbs to 1,500 lbs. To raise the tongue of a trailer this size, you'd need a jack that can handle a static load of no less than 1,500 lbs.
... This 5,000 lb electric A-frame jack runs off your 7-way, lifting your trailer with a switch, while the drop leg adds the extra reach you need to dial in height before leveling.This issue is commonly tied to factory tow packages, including Ford Trailer Tow Package and Max Trailer Tow Package, while many base models do not have the same limitation. If you want to confirm your vehicle-side 7-way is working properly, see our help article: Testing a Vehicle Side 7-Way Trailer Connector for Proper Function .
Your arm stalls mid-crank trying to lift a loaded boat trailer at the ramp. Been there. This 1,500 lb aluminum swivel jack accepts a 3/4" socket so a drill does the lifting. The wheel rolls the trailer into place and holds up to saltwater use.Roll the Trailer Into Place: Built-in wheel makes small positioning adjustments easier at the ramp or driveway. Features to know about Let Your Drill Do the Cranking Hand cranking gets old when you're hooking up before a launch or putting the trailer away afterward.
Manual jacks get old fast when you're trying to hitch up or level. This 5,000 lb electric A-frame jack plugs into your 7-way for push-button lifting and includes an integrated SnapPad for a wider, more stable base on soft or uneven ground.The integrated SnapPad adds a wider rubber base that stays attached, giving you more footing on soft ground without dragging out extra blocks. How to Pick the Right Trailer Jack Capacity Your jack needs to lift the tongue weight, usually 10 to 15% of your trailer's total weight. For example, if your trailer weighs 10,000 lbs fully loaded, your tongue weight will typically be around 1,000 to 1,500 lbs.
Hook up, check tongue weight, and get on the road with fewer steps. This kit pairs a 5,000 lb electric trailer jack with a jack foot tongue weight scale, letting you lift your trailer and verify the load during the same hitching process.Features to know about Check, Adjust, and Hitch Up When you're getting ready to tow, it's hard to know if your trailer's tongue weight is right just by looking at it. Lower your trailer onto the gauge while it's still on your jack, see where the weight stands, move your gear if needed, and check it again before you hitch up.
King pin coupler allows you to pull your gooseneck trailer with a fifth-wheel hitch. The height easily adjusts to fit your application. Square inner tube.Features: Gooseneck-to-5th-wheel adapter lets you tow your gooseneck trailer with a 5th-wheel hitch Square inner tube fits most standard, square gooseneck outer tubes Adjustable height to fit your application Sturdy steel construction Heavy-duty load-bearing pin (GCPN-PIN) sold separately SAE J2638 compliant Specs: Tube width: 3-15/16" Range of vertical adjustment: 8" 2-11/16" From center of hole to center of hole Pin hole diameter: 13/16" Plate dimensions: 10" long x 10" wide Weight capacity: 30,000 lbs 1-Year warranty
King pin coupler allows you to pull your gooseneck trailer with a fifth-wheel hitch. The height easily adjusts to fit your application. Round inner tube is included, heavy-duty load-bearing pin (GCPN-PIN) is sold separately.Features: Gooseneck-to-5th-wheel adapter lets you tow your gooseneck trailer with a 5th-wheel hitch Round inner tube fits most standard, round gooseneck outer tubes Adjustable height to fit your application Sturdy steel construction Heavy-duty load-bearing pin (GCPN-PIN) is sold separately SAE J2638 compliant Specs: Tube diameter: 4" Range of vertical adjustment: 8" 2-11/16" From center of hole to center of hole Pin hole diameter: 13/16" Plate dimensions: 10" long x 10" wide Weight capacity: 25,000 lbs 1-Year warranty
Pull the front-facing plunger pin to release the drop leg for 13-1/2" of manual adjustment. The jack provides 12-3/8" of lift, while a durable screw and built-in grease zerk help ensure smooth, reliable operation. Includes a sidewind crank.Features: Heavy-duty utility jack lets you raise and lower your trailer Ideal for agricultural and commercial applications Drop leg with spring return increases overall extension for maximum adjustability Plunger pin positioned to the front Durable 1" jack screw allows for heavy lifting Twin thrust bearings make extending and retracting jack easy Effortless greasing with built-in grease zerk Black painted inner and outer tubes Sidewind handle has curved edges - no sharp ends Handle can be secured for travel with included weld-on clip Footplate minimizes sinking in soft ground Weld-on installation Specs: Height: 28" Retracted 40-1/4" Extended Lift: 12-3/8" Drop leg adjustment: 13-1/2" Total adjustment: 25-7/8" Lift capacity: 10,000 lbs Support capacity: 12,000 lbs Outer tube width: 4" Inner tube width: 3-1/2" Footplate dimensions: 8-1/4" long x 8" wide Adjustment hole spacing on drop leg: 3-3/8" from center of hole to center of hole 1-Year warranty
This A-frame jack has a retracted height of 7-1/8" and an extended height of 22-3/8". The drop leg adds 13-1/2" of manual adjustment to 15-1/4" of lift. Includes a sidewind handle and footplate.To do this, you'll need a jack with a lift capacity high enough to handle your trailer's tongue weight. Tongue weight is the amount of weight that your trailer applies to the back of your tow vehicle. Typically, your tongue weight should be 10-15% of your total trailer weight (trailer + cargo).
Pull the side-facing plunger pin on this heavy-duty jack to release the drop leg. The durable jack screw offers increased strength- lifts up to 5 tons, and supports 6. Sidewind crank included.But, if you are just using it to stabilize or support a parked trailer, then you should focus on the jack's support capacity. Heavy-duty jacks like this one stabilize about 25% of your trailer's total weight when it's loaded up.
Pull the front-facing plunger pin on this jack to release the drop leg, adding 13-1/2" of manual adjustment to 12-3/8" of lift. Durable screw offers increased strength. Sidewind crank (TJD-12000-HD) sold separately.Features: Heavy-duty utility jack lets you raise and lower your trailer Ideal for agricultural and commercial applications Drop leg with spring return increases overall extension for maximum adjustability Plunger pin positioned to the front Durable 1" jack screw allows for heavy lifting Twin thrust bearings make extending and retracting jack easy Effortless greasing with built-in grease zerk Black painted inner and outer tubes Sidewind handle (TJD-12000-HD) sold separately Handle can be secured for travel with weld-on clip (TJD-12000-CLIP - sold separately) Footplate minimizes sinking in soft ground Weld-on installation Specs: Height: 28" Retracted 40-1/4" Extended Lift: 12-3/8" Drop leg adjustment: 13-1/2" Total adjustment: 25-7/8" Lift capacity: 10,000 lbs Support capacity: 12,000 lbs Outer tube width: 4" Inner tube width: 3-1/2" Footplate dimensions: 8-1/4" long x 8" wide Adjustment hole spacing on drop leg: 3-3/8" from center of hole to center of hole 1-Year warranty
... This 3,500 lb electric A-frame jack runs off your 7-way, lifting your trailer with a switch, while the drop leg adds the extra reach you need to dial in height before leveling.This issue is commonly tied to factory tow packages, including Ford Trailer Tow Package and Max Trailer Tow Package, while many base models do not have the same limitation. If you want to confirm your vehicle-side 7-way is working properly, see our help article: Testing a Vehicle Side 7-Way Trailer Connector for Proper Function .
Weld-on jack has a retracted height of 24-3/4" and an extended height of 40-1/8". The square design provides solid side-load support. The drop leg adds 13-1/2" of manual adjustment to 15-3/8" of lift. Sidewind handle included.Features: Utility jack lets you raise and lower your trailer Ideal for agricultural and commercial applications Square jack provides more side-load capacity than round-tube jacks Sidewind handle has zinc finish for attractive look and rust resistance Drop leg allows for increased lift and saves time when raising or lowering Pin and clip holds leg at desired location Effortless greasing with built-in grease zerk Black painted outer tube Zinc finished inner tube and footplate for corrosion resistance Welded-on footplate minimizes sinking in soft ground Weld-on installation Specs: Height (from bottom of foot to top of jack): 24-3/4" Retracted 40-1/8" Extended Lift: 15-3/8" Drop leg adjustment: 13-1/2" Total adjustment: 28-7/8" Lift capacity: 7,000 lbs Support capacity: 8,000 lbs Outer tube width: 2-1/2" Inner tube width: 2-1/4" Footplate dimensions: 7-7/8" long x 6" wide Handle radius: 7-3/4" Adjustment hole spacing on drop leg: 3-3/8" from center of hole to center of hole 3-1/2" Between center of hole on bottom and center of nearest hole 1-Year warranty
Your arm stalls mid-crank with a loaded tongue. Been there. This A-frame jack lifts up to 2,000 lbs and accepts a 3/4" socket so a drill can do the work. You raise and lower smoothly without fighting the handle, and hitching doesn't drag on.If the drill isn't nearby, just flip the handle back up and crank it manually. 2,000 lbs of Lifting Capacity With a 2,000-lb maximum capacity and 14" of travel, this jack handles the tongue weight of loaded campers, utility trailers, and other towables. Raise the coupler to clear the hitch ball, line everything up, and lower it into place without wrestling with the front of the trailer.
Filters
